ISUZU TFS SERIES 1997 Workshop Manual

10-24 CAB
Important Operations
9.Window Glass
Insert the window glass into position by tilting it as
necessary, then set it against the channel of the window
regulator.
Attach the window glass to the window regulator with the
two screws.
10.Water Proof Sheet
Place the butyl type on the door panel so as not to cover
the drain hole.
25.Regulator Handle
Install the regulator handle as illustrated when closing
the window glass.

CAB 10-25
ADJUSTMENT (FRONT AND REAR)
Door Hinge
Door alignment can be obtained by moving door hinges.
Prior to adjustment, remove the fender and set the door
temporarily.
Loosen hinge to door bolts when adjusting steps between the
door and body.
Loosen hinge to body bolts to adjust the clearance between the
door and body.
Door Striker
Loosen the striker screws and adjust the position of the striker
by holding a piece of wood against the striker and tapping it
with a hammer.
To obtain correct adjustment, move the position of the striker
vertically so that the lower face of the dovetail becomes parallel
to the striker.
Adjust the number of sheets to control engagement of the
striker with the door latch. One or two sheets are generally
used to obtain correct adjustment.

10-26 CAB
INSTRUMENT PANEL
REMOVAL
2 9
6
715 1013 81211
4
3
Disassembly Steps
1. Center console assembly
2. ECM cover (M/T Remote only)
3. Glove box
4. Glove box cover
5. Instrument panel passenger lower cover
assembly
6. Instrument panel driver lower cover
assembly
7. Lower cluster assembly
8. Meter cluster assembly
9. Instrument panel lower center cover
assembly
10. Control lever assembly
11. Instrument panel assembly
12. Meter assembly
13. Radio assembly

CAB 10-27
Important Operations
1. Center Console Assembly
Remove shift knob and 2 fixing screws (front side).
Open the grommet and remove 2 fixing screws (rear
side).
2. ECM cover
3. Glove Box
Remove 2 fixing screws and pulling the handle.
4. Glove Box Cover
Remove 4 fixing screws and pull the cover toward you
and remove the clips at 2 positions.
5. Instrument Panel Passenger Lower Cover Assembly
Remove 3 fixing screws and 1 clip.
6. Instrument Panel Driver Lower Cover Assembly
Remove the engine hood opener 2 fixing screws and 6
fixing screws.
Disconnect the connector of the illumination.
7. Lower Cluster Assembly
Remove 3 fixing clips.
8. Meter Cluster Assembly
Remove 3 fixing screws, 7 clips and switch connectors.
9. Instrument Panel Lower Center Cover Assembly
Remove 7 fixing screws and disconnect the connector of
the cigarette lighter.

10-28 CAB
10.Control Lever Assembly
1) Disconnect the control cable from heater unit and blower
unit.
2) Remove the control lever assembly fixing screws.
11.Instrument Panel
1) Remove the instrument panel fixing nuts and bolts.
2) Disconnect the instrument harness on ECM.
3) Remove the instrument panel.

CAB 10-29
INSTALLATION
12
Installation Steps
1. Radio assembly
2. Meter assembly
3. Instrument panel assembly
4. Control lever assembly
5. Instrument panel lower center cover
assembly
6. Meter cluster assembly7. Lower cluster assembly
8. Instrument panel driver lower cover
assembly
9. Instrument panel passenger lower cover
assembly
10. Glove box cover
11. Glove box
12. ECM cover (M/T Remote only)
13. Center console assembly

10-30 CAB
4. Control Lever Assembly
1) Set the temperature control lever and the airsource
select lever at the left-hand side end.
2) Set the air selector lever at the right-hand side end.
1 : Temperature control cable
2: Air source select cable
3: Air selector
3) Attach the cable, after the work 1) and 2) have been
completed.

CAB 10-31
CONSOLE BOX
REMOVAL AND INSTALLATION
6 51 2 4
3
44 S Model
Removal Steps
1. Hole cover 2
2. Screw
2
3. Screw
2
4. Center console
5. Screw
4
6. Rear console
Installation Steps
6. Rear console
5. Screw
4
4. Center console
3. Screw
2
2. Screw
2
1. Hole cover
2

10-32 CAB
CONSOLE BOX
REMOVAL AND INSTALLATION
4 5
3
2 1
4
2 LS Model 44 LS Model
42 LS AND 44 LS Model
Removal Steps
1. Screw 4
2. Rear console
3. Screw
2
4. Screw
2
5. Center console
Installation Steps
5. Center console
4. Screw
2
3. Screw
2
2. Rear console
1. Screw
4

CAB 10-33
HEAD LINING
GENERAL DESCRIPTION
STANDARD CAB
SPACE CAB (SPORTS CAB)