ECU JAGUAR X308 1998 2.G Workshop Manual

Interior Trim and Ornamentation - Front Door Trim Panel Finish Panel
Removal and Installation
Removal
Installation



1. Remove interior door handle escutcheon.
Remove cover from door ha ndle escutcheon securing
screw and slacken and remove screw.
Pull door handle inwards and exercising care to avoid
damaging tweeter, remove escutcheon from casing.

2. Remove veneer panel from casing.
1. Using a thin plastic leve r, carefully ease rear of
veneer panel inwards to release the two rear
securing tangs.
2. Slide veneer panel re arwards to release front
retainers.
1. Position veneer panel on casing and slide forward to engage
front retainers.
2. Using a soft pad or cloth, press re ar of panel firmly to seat the
securing tangs.
3. Fit door handle escutcheon.

Interior Trim and Ornamentation - Front Door Stowage Compartment
Removal and Installation
Removal
Installation

1.
Remove door casing for access. Refer to 76.34.01.

2. Remove pocket from door casing.
1. Release puddle lamp harness from clips at base of door pocket.
2. Slacken and remove th e two screws securing
bottom of pocket to casing.
3. Remove two spring clips securing top of pocket to casing.
3. Lift pocket out of casing .
1. Position pocket in casing and secure with screws and spring
clips.
2. Position puddle lamp harn ess in pocket clips.
3. Fit door casing. Refer to 76.34.01.

Interior Trim and Ornamentation - Front Door Trim Panel
Removal and Installation
Removal

1. Remove interior door handle escutcheon.
Remove cover from door ha ndle escutcheon securing
screw and slacken and remove screw.
Pull door handle inwards and exercising care to avoid
damaging tweeter, remove escutcheon from casing.
2. Remove door casing veneer panel. Refer to 76.47.11.

3. Slacken and remove the armres t centre securing screw.

4. Carefully release the eight fasten ers securing lower section of
casing to door.

5. Lift rear edge of door casing to release retaining clip housing
from door panel.

6. Lift casing clear of door wais t flange and lock button and
withdraw for access.
7. Using pliers, remove housing from clip and fit to door panel.

8. Disconnect tweeter, speaker, puddle lamp and switchpack
harness multiplugs.
9. Remove armrest lower securing clip housing from casing. and
refit to door.

10. Remove door inner waist se al from holder, slacken and
remove screws securing waist seal holder and remove seal
holder.
11. Remove armrest from door casing. Refer to 76.34.22.

12. Slacken and remove puddle la mp securing screws and
remove lamp assembly from casing.
13. Remove pocket from door casing.

Installation



1. Release puddle lamp harness from clips at base of door pocket.
2. Slacken and remove th e two screws securing
bottom of pocket to casing.
3. Remove two spring clips securing top of pocket to casing.
14. Lift pocket from casing.

15. Slacken and remove door sp eaker securing screws and
remove speaker from casing.
1. Fit and fully seat casing securing clips.
2. Position speaker grill in casing align speaker and fit and tighten
securing screws.
3. Position pocket in casing and secure with screws and spring
clips.
4. Fit puddle lamp to casing, fit and tighten securing screws and
position harness in pocket clips.
5. Fit door armrest to casing. Refer to 76.34.23.
6. Fit inner waist seal holder to casing and fit and tighten the
securing screws.
7. Align and fit inner waist seal.
8. Fit door armrest to casing. Refer to .
9. Check that armrest tang locater and screw insert are correctly
positioned in door panel.
10. Position casing for access and connect tweeter, speaker,
puddle lamp and switchpack harnesses.
11. Finally position casing locating fold over waist flange and
firmly press armrest to locate retaining tang in door panel.
12. Commencing at front , press and firmly seat casing lower
fasteners in door inserts.
13. Fit and tighten armrest centre se curing screw in door insert.
14. Fit door casing veneer panel. Refer to 76.47.11.
15. Position door handle escutche on on casing, fit and tighten
securing screw and fit cover over screw.

Interior Trim and Ornamentation - Luggage Compartment Front Trim
Panel
Removal and Installation
Removal
Installation

1.
Remove battery cover.
2. Remove trunk floor carpet.

3. Remove and discard the two fir tree fasteners securing the
front liner.
4. Remove liner from trunk.
1. Position liner in trunk.
2. Using new fir tree fasteners, secu re liner to front of trunk.
3. Fit trunk floor carpet.
4. Fit battery cover.

Interior Trim and Ornamentation - Luggage Compartment Lid Trim Panel
Removal and Installation
Removal
Installation
1. Remove trunk lamp assemblies. Refer to 86.45.16.

2. Release the three warning triang le securing clips and remove
warning triangle.

3. Slacken and remove warning triangle mounting bracket
securing screws an d remove bracket.

4. Remove covers from trunk latc h finisher securing bolts,
slacken and remove bolts and remove finisher.

5. Remove and discard the eighteee n trunk lid liner fasteners and
remove liner from vehicle.

1.
Position liner on trunk lid and pass lamp harness multiplugs
through apertures.
2. Align and fully seat liner on trunk lid and secure with new
fasteners.
3. Position finisher over trunk lid latch, fit and tighten securing
bolts and fit bolt covers..
4. Position warning triangle mounti ng bracket and fit and tighten
securing screws.
5. Install triangle on mounting br acket and secure with clips.
6. Install trunk lamp assemblies. Refer to 86.45.16.

Interior Trim and Ornamentation - Luggage Compartment Rear Trim Panel
Removal and Installation
Removal
Installation



1. Remove tail lamp covers.
2. Remove trunk floor and battery cover. Refer to operations in
this section.

3. Remove and discard the two fir tr ee fasteners securing finisher
to trunk rear panel.

4. Pull rear finisher upwards to release upper spring clips and
remove finisher from trunk.
1. Position finisher on trunk rear panel and press firmly
downwards to engage spring clips.
2. Fit and fully seat fir tree fasteners.
3. Fit trunk floor and battery cover. Refer to operations in this
section.
4. Fit tail lamp covers.

Interior Trim and Ornamentation - Overhead Console Finish Panel
Removal and Installation
Removal
Installation

1.
Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
2. Remove roof console. Refer to 76.13.69.90.

3. Bend back veneer panel retain ing tangs from console and using a thin blade, carefully release panel from console.
1. Remove backing paper and apply adhesive pad to back of
panel.
2. Position and fully seat ve neer panel on console.
3. Bend retaining tangs to secure veneer panel to console.
4. Install roof console. Refer to 76.13.69.90.
5. Connect ground cable to batter y terminal and install battery
cover. Refer to 86.15.15.