JEEP RENEGADE 2014 1.G Owners Manual

DEACTIVATING THE
DEVICE
The device is deactivated by pressing
button
or bringing the ignition
device to STOP.
WARNING
123)While travelling with the device
activated, do not move the gear lever to
neutral.
124)In the event of device faults or failures,
go to a Jeep Dealership.
125)The electronic Cruise Control can be
dangerous if the system cannot keep a
constant speed. In specific conditions
speed may be excessive, resulting in the
risk of losing control of the vehicle and
causing accidents. Do not use the device
in heavy traffic or on winding, icy, snowy or
slippery roads.
FOUR WHEEL DRIVE
JEEP ACTIVE
DRIVE (4WD) and
JEEP ACTIVE DRIVE
LOW (4WD LOW)
ALL-WHEEL DRIVE
The four wheel drive (4WD) is fully
automatic in standard driving mode.
IMPORTANT Changing mode is not
possible when the vehicle speed is over
120 km/h.
Four wheel drive activation
40) 41)
The buttons to activate the four wheel
drive are located on the device
Selec-Terrain™and can select:
❒4WD LOCK (fig. 93 versions with
manual gearbox and automatic
translation): deactivates the function for
disconnecting the propeller shaft,
guaranteeing the immediate availability
of the torque to the rear coupling.
This function can be selected in AUTO
mode and in the other driving modes.
❒4WD LOW (fig. 94 versions with
automatic transmission): it enhances
the "off-road" performance of the
vehicle in all driving modes;The 4WD LOCK function can be
activated by pressing the dedicated
button or when the selector is rotated
from AUTO to SNOW/SAND/MUD
or ROCK (Trailhawk versions) and 4WD
LOW was not selected before.
The engagement of one function (e.g.
4WD LOW) deactivates the other one
automatically.
93J0A0155C
109

IMPORTANT On some versions,
pressing the button 4WD LOW
it automatically activates the 4WD
LOCK function as well. If the 4WD LOW
button is pressed again, the 4WD
LOCK function will be activated. If,
however, the 4WD LOCK button is
pressed again, both functions will be
deactivated.
IMPORTANT The 4WD LOW function is
recommended for irregular and slippery
terrain only.
4WD LOW MODE
ENGAGEMENT/RELEASE
4WD LOW mode
engagement
With vehicle at a standstill, ignition
device in MAR position or with engine
on, move the gear lever to position
D (Drive), R (Reverse) or N (Neutral) and
press the 4WD LOW button.
On some versions, with mode
engaged, the display shows "4WD
LOW". The LED on theSelec-
Terrain™device may flash until the
end of the engagement.
4WD LOW mode release
The release can occur at any speed
ranging from 0 to 120 km/h.
On some versions, "4WD LOW" on the
display switches off at the end of the
release procedure.
In this case, the LED on the 4WD LOW
button is off.
WARNING
40)The correct operation of the 4WD
function depends on the tyres: all of them
must have the same size, the same type
and the same circumference. The use
of tyres of the wrong size could interfere
with gear changes and damage
transmission components.41)Do not drive at speeds exceeding
those permitted by the conditions of the
road.
94J0A0156C
110
STARTING AND DRIVING

SELEC-TERRAIN
DRIVING MODE
SELECTION
Turn knob A fig. 95 to select the wished
mode.
IMPORTANT Changing mode is not
possible when the vehicle speed is over
120 km/h.❒AUTO (Automatic): the 4WD mode
with continuous and automatic
operation can be used while driving on
road and off-road. This mode reduces
fuel consumption, because the
propeller shaft can be disconnected,
whenever required.
❒SNOW: this mode can achieve more
stability on slippery or snow-covered
grounds. To be used for driving on-road
and off-road in the case of grounds
with poor grip, such as roads covered
by snow.
❒SAND: off-road driving mode to be
used on grounds with poor grip, such
as muddy surfaces. The transmission is
set to offer a maximum traction.
❒MUD: off-road driving mode for
surfaces with poor grip, such as
mud-covered grounds or wet grass.
❒ROCK(where provided, for Trailhawk
versions only): this mode is only
available if the 4WD LOW mode is
activated. The device sets the vehicle to
maximise traction and give the highest
steering capacity on off-road surfaces
featuring a high grip. This mode offers
the best performance when driving
"off-road". This mode must be used to
pass over obstacles at slow speed,
such as large rocks, deep cracks, etc.When the engine is started, the AUTO
mode is automatically selected (LED on
close to the AUTO wording).
Turning the knob A fig. 95 the LED
close to the AUTO wording comes on
solid. The other LEDs switch on
sequentially, depending on the
positions set on the knob, so that the
driver can understand which is the new
required mode.
Once the required mode is set (LED
close to the wording switched on), just
keep the knob in that position so that
theSelec-Terrain™system actuates
to engage the wished mode.
95J0A0153C
111

PARKSENSE
SYSTEM
SENSORS
126)42) 43)The parking sensors, located in the rear
bumper fig. 96, are used to detect the
presence of any obstacles near the rear
part of the vehicle.
The sensors warn the driver about the
presence of obstacles with an
intermittent acoustic signal and, where
provided, also with visual indications
on the instrument panel display.
ACTIVATION/
DEACTIVATION
If the system has been correctly turned
on, it will activate automatically when
the reverse is engaged.
Instead, the system automatically
deactivates bringing the gear lever to a
position different from reverse.
ENGAGEMENT/
DISENGAGEMENT
To disengage the system press button
fig. 97.
When the system passes from engaged
to disengaged and viceversa, it is
always accompanied by a dedicated
message shown on the instrument
panel display.When the system is disengaged, the
LED on the button is off. Instead, if the
system is disengaged, the LED is on
constantly. The LED lights up also in the
case of a fault to theParkSense® sys-
tem.
If the button is pressed with the system
faulty, the LED flashes for about 5
seconds, then it stays on constantly.
IMPORTANT After theParkSense®
has been disengaged, it will stay in this
condition until the following engage-
ment, even if the ignition device passes
from MAR to STOP and then again to
MAR.
OPERATION WITH
TRAILER
The operation of the sensors is
automatically deactivated when the
trailer's electric plug is inserted in the
vehicle's tow hook socket.
96J0A0166C
97J0A0227C
112
STARTING AND DRIVING

The sensors are automatically
reactivated when the trailer's cable plug
is removed. Before using thePark-
Sense® system, it is recommended to
remove the tow hook ball assembly and
the relevant attachment from the vehi-
cle when the latter is not used for tow-
ing operations. Failure to comply with
this prescription may cause personal
injuries or damages to vehicles or
obstacles since, when the continuous
acoustic signal is emitted, the tow hook
ball is already in a position that is much
closer to the obstacle than the rear
bumper.
In addition, the sensors may detect the
tow hook ball assembly and the
relevant attachment (depending on its
size and shape), providing a false
indication of the presence of an
obstacle in the area behind the vehicle.
GENERAL WARNINGS
Some conditions may influence the
performance of the parking system:
❒reduced sensor sensitivity and a
reduction in the parking assistance
system performance could be due to
the presence of: ice, snow, mud, thick
paint, on the surface of the sensor;
❒the sensor may detect a non-existent
obstacle ("echo interference") due to
mechanical interference, for example
when washing the vehicle, in rain
(strong wind), hail;❒the signals sent by the sensor can
also be altered by the presence of
ultrasonic systems (e.g. pneumatic
brake systems of trucks or pneumatic
drills) near the vehicle;
❒Parking assistance system
performance can also be influenced by
the position of the sensors, for example
due to a change in the ride setting
(caused by wear to the shock
absorbers, suspension), or by changing
tyres, overloading the vehicle or
carrying out specific tuning operations
that require the vehicle to be lowered.
❒the presence of a tow hook without
trailer, which may interfere with the
correct operation of the parking
sensors.
❒the presence of adhesives on the
sensors. Thus take care not to place
adhesives on the sensors.
WARNING
126)Parking and other potentially
dangerous manoeuvres are, however,
always the driver’s responsibility. When
performing these operations, always make
sure that there are no other people
(especially children) or animals on the route
you want to drive into. The parking
sensors are an aid for the driver, but the
driver must never allow their attention
to lapse during potentially dangerous
manoeuvres, even those executed at low
speeds.
WARNING
42)The sensors must be clean of mud,
dirt, snow or ice in order for the system to
operate correctly. Be careful not to scratch
or damage the sensors while cleaning
them. Avoid using dry, rough or hard
cloths. The sensors should be washed
using clean water with the addition of car
shampoo if necessary. When using special
washing equipment such as high pressure
jets or steam cleaning, clean the sensors
very quickly keeping the jet more than
10 cm away.
43)Only have interventions on the bumper
in the area of the sensors carried out by
a Jeep Dealership. Interventions on the
bumper that are not carried out properly
may compromise the operation of the
parking sensors.
113

LANESENSE
SYSTEM (lane
crossing warning)
DESCRIPTION
44) 45) 46) 47) 48) 49)
The LaneSense system makes use of a
camera located on the windscreen to
detect the lane limits and calculate
the position of the vehicle within such
limits, in order to make sure that it
remains inside the lane.
When both limits of the lane are
detected and the vehicle crosses one of
them without the awareness of the
driver (direction indicator off), the
system provides a tactile warning by
applying torque to the steering wheel,
signalling the driver that he must take
an action to remain into the lane.
If the vehicle continues going beyond
the line of the lane without any
intervention from the driver, the
warning light (or the corresponding
graphic icon on the reconfigurable
multifunction display) will be displayed
on the instrument panel to urge the
driver to bring the vehicle back into the
limits of the lane.IMPORTANT The system monitors the
presence of the driver's hands on
the steering wheel. If they are
not detected, the system emits an
acoustic signal and deactivates until it is
reactivated by pressing the dedicated
button.
When one limit of the lane is detected
and the vehicle crosses it (direction
indicator off), warning light
(or the
icon on the reconfigurable multifunction
display) will be displayed on the
instrument panel to urge the driver to
bring the vehicle back into the lane.
In this case, the tactile warning (torque
on the steering wheel) is not provided.
SYSTEM ACTIVATION/
DEACTIVATION
When the engine is started the system
is activated (LED on button
fig. 98
off). Each time the engine is started, the
system keeps the activation status
there was when it was previously
switched off.
Activation conditions
Once switched on, the system
becomes active only if the following
conditions are met:
❒the driver always keeps at least one
hand on the steering wheel;❒vehicle speed ranges within 60 km/h
and 180 km/h (or equivalent values in
miles);
❒the lane limit lines are perfectly visible
on both sides;
❒there are suitable visibility conditions;
❒the road is straight or with wide
radius bends;
❒a suitable distance is kept from the
vehicle in front;
❒the direction indicator (for leaving the
lane) is not active;
❒the lane limit lines are perfectly visible
on both sides (for activation of the
tactile warning only).
NOTE The system does not apply
torque to the steering wheel every time
a safety system is activated (brakes,
ABS, ASR system, ESC system,
Forward Collision Warning Plus system,
etc.).
98J0A0052C
114
STARTING AND DRIVING

WARNING
44)The camera may have limited or absent
operation due to weather conditions such
as: heavy rain, hail, thick fog, heavy snow,
formation of ice layers on the windscreen.
45)Camera operation may also be
compromised by the presence of dust,
condensation, dirt or ice on the
windscreen, by traffic conditions (e.g.
vehicles that are driving not aligned with
yours, vehicle driving in a transverse or
opposite way on the same lane, bend with
a small radius of curvature), by road
surface conditions and by driving
conditions (e.g. off-road driving). Make sure
the windscreen is always clean. Use
specific detergents and clean cloths to
avoid scratching the windscreen. The
camera operation may also be limited or
absent in some driving, traffic and road
surface conditions.
46)Projecting loads on the roof of the
vehicle may interfere with the correct
operation of the camera. Before starting
make sure the load is correctly positioned,
in order not to cover the camera operating
range.
47)If the windscreen must be replaced
due to scratches, chipping or breakage,
contact exclusively a Jeep Dealership. Do
not replace the windscreen on your own,
risk of malfunction! It is advisable to replace
the windscreen if it is damaged in the area
of the camera.48)Do not tamper nor operate on the
camera. Do not close the openings in the
aesthetic cover located under the interior
rear view mirror. In the event of a failure
of the camera, contact a Jeep Dealership.
49)Do not cover the operating range of the
camera with stickers or other objects.
Also pay attention to other objects on the
bonnet (e.g. a layer of snow) and make
sure they do not interfere with the camera.
REAR CAMERA
(PARKVIEW® REAR
BACKUP CAMERA)
DESCRIPTION
127)50)The camera is located on the tailgate
fig. 99.
Every time reverse is engaged, the
display fig. 100 of theUconnect™
system shows the area around the
vehicle, as seen by the rear camera.
SYMBOLS AND
MESSAGES ON THE
DISPLAY
The active line grid is positioned on the
image to illustrate the width of the
vehicle and the expected reversing path
in accordance with the steering wheel
position.
99J0A0102C
115

A superimposed central broken line
indicates the centre of the vehicle
to facilitate parking manoeuvres or tow
hook alignment.
The various coloured areas indicate the
distance from the rear of the vehicle.
Area (reference
fig. 100)Distance from the
rear of the vehicle
Red (A) 0–30 cm
Yellow (B) 30–100 cm
Green (C) 1 m or more
IMPORTANT When parking, take the
utmost care over obstacles that may be
above or under the camera range.
WARNING
127)Parking and other potentially
dangerous manoeuvres are, however,
always the driver’s responsibility. While
carrying out these manoeuvres, always
make sure that no people (especially
children) or animals are in the area
concerned. The camera is an aid for the
driver, but the driver must never allow
his/her attention to lapse during potentially
dangerous manoeuvres, even those
executed at low speeds. Always keep a
slow speed, so as to promptly brake in the
case of obstacles.
WARNING
50)It is vital, for correct operation, that the
camera is always kept clean and free
from mud, dirt, snow or ice. Be careful not
to scratch or damage the camera while
cleaning it. Avoid using dry, rough or hard
cloths. The camera must be washed
using clean water, with the addition of car
shampoo if necessary. In washing stations
which use steam or high-pressure jets,
clean the camera quickly, keeping the
nozzle more than 10 cm away from the
sensors. Do not apply stickers to the
camera.
100J0A0103C
116
STARTING AND DRIVING

TOWING TRAILERS
TOW HOOK SETUP
128) 129)
Instructions for using the
removable ball head tow
bar
IMPORTANT Before setting off,check
the correctlockingof the removable
ball head tow bar, as follows:
❒the green mark of the knob must
coincide with the green mark on the
tow bar;
❒the knob is in the stop position on
the tow bar (without slot);
❒locked lock and key removed. The
knob cannot be removed;
❒ball head bar firmly secured to the
housing pipe. Check by shaking with a
hand.
The fitting procedure must be repeated
if any of the requirements are not met.
If even only one of the requirements
is not met the tow hookmust notbe
used, since there is risk of causing
accidents. Contact a Jeep Dealership.
The ball head tow bar can be
fitted/removed manually, without
requiring specific equipment.
IMPORTANT Never use vehicles or
work tools: the mechanism may be
damaged.IMPORTANT Never unlock in the case
of trailer attached to the vehicle or
with rack fitted.
IMPORTANT When driving without
trailer (or without rack), the ball head
tow bar must be removed and the
closing plug must always be inserted in
the housing pipe. This applies
particularly if, due to the bar, the
visibility of the number plate or of the
lighting system is reduced.
117

REMOVABLE BALL HEAD TOW BAR



101J0A0423C
118
STARTING AND DRIVING