lock LAND ROVER DISCOVERY 1995 Repair Manual

V8i
11
REPAIR FLEXIBLE DRIVE PLATE AND RING GEAR
Service repair no - 12.53.13
Remove
1.Remove transmission.
See AUTOMATIC
GEARBOX, Repair, LT230T Transfer Gearbox
with Automatic Gearbox Assembly - V8i
2.Remove flexible drive plate and ring gear
assembly.
See V8i Overhaul Manual.
Refit
3.Clean all components for reassembly.
4.Fit ring gear and flexible drive plate assembly.
See V8i Overhaul Manual.
5.Fit transmission.CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
1.Automatic transmission, remove drive plate.
See Flexible Drive Plate and Ring Gear
OR manual transmission, remove flywheel.See
Flywheel
2.Remove sump.See Oil Sump
3.Remove rear main bearing cap.
4.Remove cross seals from cap.
5.Remove crankshaft rear oil seal.
6.Clean main bearing cap and oil seal area of
block.
7.Fit new cross seals to bearing cap.
8.Apply Hylomar SQ32M to block as illustrated.
9.Lubricate bearing shell and cross seals using
clean engine oil.
10.Fit bearing cap, do not tighten bolts.
11.Ensure cap is fully home and seated squarely on
the block.

V8i
13
REPAIR
NOTE: Release bolts securing compressor
mounting bracket to engine and remove
bracket to enable temporary lifting eye
ETC 5964 to be fitted. Secure lifting eye to
mounting bracket fixing points with suitable bolts
of equivalent size, pitch and thread. Leave lifting
eye attached until engine is reinstalled in vehicle.
15.Place drain tray underneath vehicle.
16.Disconnect hose from reservoir to power
steering pump. Secure hose end above level of
fluid reservoir to avoid unnecessary loss of fluid.
17.Disconnect power steering pump to power
steering box hose. Seal hose and pump
openings with masking tape to prevent ingress of
dirt. Wipe away any fluid spillage from chassis or
steering box.
18.Disconnect fuel temperature and coolant
temperature sensor multi-plugs.
19.Disconnect leads from coil.
20.Identify each injector multi-plug for re-assembly
and disconnect plugs from injectors.
21.Manoeuvre harness from behind fuel rails and
place to one side clear of engine assembly.
22.Remove two clamps securing gearbox oil cooler
pipes to engine block.
23.Remove engine mounting fixings on both sides
of cylinder block.
24.Fit lifting chains to engine lifting eyes as shown
in illustration RR1780E.
1. L/H Front chain 356mm total overall length.
2. R/H Front chain 330mm total overall length.
3. R/H Rear chain 457mm total overall length.
NOTE: All chain dimensions are measured
from end of lifting hook to end of last link
in chain.
25.Fit chain lifting eye to a suitable engine hoist.
Raise hoist high enough to enable engine
mountings to be removed, and withdraw rubber
mountings.
26.Lower hoist until engine rests securely on engine
mounting brackets. Remove lifting chains and
hoist.
27.Disconnect two heater hoses located on top of
right hand rocker cover.
28.Remove ground strap from rear of left hand
cylinder head. DO NOT remove from retaining
clip.
29.Remove all electrical harnesses from retaining
clips at rear of engine.
30.Remove transmission breather pipes from
retaining clip on rear lifting eye.
31.Remove top two bolts securing bell housing to
cylinder block.
32.Raise front of vehicle, lower vehicle on to axle
stands.
33.Remove bell housing bottom cover. Remove
gasket from bell housing face.
34.Remove nuts securing exhaust downpipes to
manifolds, remove heat shield from right hand
side downpipe.
35.Remove electrical leads from starter motor
solenoid. Disconnect multi-plug from oil level
sensor on side of sump, if fitted.
NOTE: Instructions 37, 38 and 39 refer to
automatic vehicles only.
36.With assistance rotate engine at crankshaft
pulley until two access holes in drive plate/ring
gear assembly are visible.
37.Remove two bolts visible through access holes.
Mark one access hole and one bolt hole to
ensure unit is reassembled in its original position
38.Rotate crankshaft 180Ê until two remaining
access holes are visible, remove two bolts.

12ENGINE
14
REPAIR
39.Remove remaining bell housing to cylinder block
bolts.
40.Remove starter motor ground strap from
chassis.
41.Remove stands and lower vehicle.
42.Position hydraulic trolley jack under bell housing
to support gearbox when engine and gearbox
are separated.
43.Fit lifting chains to engine. Carefully raise hoist a
little, ease engine and gearbox apart, steady
engine on hoist.
44.Ensure no components remain that will prevent
engine being removed.
45.Slowly raise engine clear of engine
compartment. Move engine away from vehicle
and place on a suitable engine stand.
Refit
46.Fit lifting chains to engine. Raise engine using
hoist.
47.Lower engine into engine compartment. Ensure
all components are clear of engine assembly.
48.Automatic vehicles: With assistance, manoeuvre
engine until bottom two engine and bellhousing
bolt holes align. Ensure that two cylinder block
dowels locate in bell housing.
Manual vehicles: Lower engine into position.
Locate primary pinion into clutch. Engage bell
housing dowels.
49.Fit two bolts and partially tighten.
50.Remove jack and lower hoist until engine rests
securely on engine mounting brackets.
51.Fit top two bell housing securing bolts. Tighten
to
40 Nm.
52.Fit remaining bell housing to cylinder block bolts.
Tighten to
40 Nm.
53.Automatic vehicles: With assistance, rotate
crankshaft pulley, line up marked holes in drive
plate and torque converter. Fit two bolts.
Tighten to
40 Nm.
54.Rotate crankshaft 180°and fit remaining two
bolts tighten to correct torque,
40 Nm.
55.Fit new gasket and refit bottom cover, tighten
bolts to
9 Nm.
56.Fit new exhaust flange gaskets, fit exhaust to
manifold.
57.Refit all harnesses, ground straps breather pipes
and hoses at rear of engine.
58.Raise engine and refit engine mounting rubbers,
tighten nuts to
20 Nm.
59.Remove temporary lifting eye ETC 5964 and
reverse instructions 1 to 23, ensuring that all
electrical plugs and harnesses are fitted in
correct locations.

V8i
15
REPAIR OIL SUMP
Service repair no - 12.60.44
Remove
1.Drain engine oil
See SECTION 10,
Maintenance, Under Vehicle Maintenance
2.Fit drain plug. Tighten to40 Nm.
3.If fitted, disconnect low oil level sensor multiplug.
4.Remove bolt securing dipstick tube to rocker
cover.
5.Working form the centre outwards, progressively
loosen and remove 17 bolts securing sump.
Remove sump.
6.Remove all traces of sealant from mating
surfaces of sump, cylinder block and front cover,
using a suitable solvent or plastic scraper.
7.Degrease mating surfaces of sump, cylinder
block and front cover.Refit
8.Apply RTV Hylosil White sealant to mating
surface of sump.
9.Position sump, tighten bolts finger tight.
10.Tighten bolts progressively in sequence shown.
Tighten to
18 Nm.
11.Fit bolt securing dipstick tube to rocker cover.
12.If fitted, connect low oil level sensor multiplug.

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine
Adaptor plate to crankshaft 84........................................................................
Generator and power steering mounting bracket to cylinder head 30............
Cylinder head:
Stage 1: 20.............................................................................................
Stage 2: - Further 180°±5°
Drive plate to converter 39..............................................................................
Engine mountings to engine and chassis 55..................................................
Engine mounting rubbers to brackets 30........................................................
Flexible drive plate to crankshaft adaptor plate 41.......................................... **
Flywheel to crankshaft bolts 78....................................................................... **
Lifting eye to cylinder heads 39......................................................................
Main bearing cap rear bolts 92....................................................................... *
Oil sump drain plug 40....................................................................................
Oil sump to cylinder block 18..........................................................................
Rocker cover to cylinder head 9....................................................................
Rocker shaft bracket to cylinder head 38........................................................
Spark plug 21..................................................................................................
Starter motor attachment 44...........................................................................
* These bolts must have threads coated in lubricant EXP16A before assembly.
** These bolts must have threads coated in sealant Loctite 270
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................
NOTE: Torque values above are for all screws and bolts used except for those specified.

12ENGINE
4
REPAIR 39.Release battery positive lead terminal cover.
40.Remove terminal nut
41.Release terminal from battery.
42.Release fusebox main feed lead.
43.Position battery cable over engine.
44.Pivot jockey pulley downwards to release drive
belt tension.
45.Release belt from pulleys.
46.Remove drive belt.
47.Disconnect compressor multiplug
48.Remove 4 bolts securing compressor.
49.Remove heatshield.
50.Release compressor from bracket and tie aside.
51.Slacken clip securing PAS hose to pump.
52.Disconnect hose.
53.Plug hose and pump.
54.Disconnect PAS hose connection at pump and
steering box.
55.Release unions and remove hose.
56.Remove and discard 'O' rings.
57.Plug pump and steering box.
58.Remove LH and RH engine mounting nuts.
59.Position lifting chains and attach hooks to engine
lifting eyes.
60.Raise engine sufficiently to release engine
mountings.
61.Release engine mountings and remove.
62.Lower engine until it just rests on engine
mounting brackets.
63.Disconnect chains.
64.Raise ramp.
65.Remove catalytic converter/front pipe assembly.
See EMISSION CONTROL, Repair, Catalytic
Converter/Front Pipe - 4.0 V8
66.Remove 9 bolts securing bell housing bottom
cover. Note position of 2 dowel bolts.
67.Remove cover.
68.Remove locknut securing transfer box tie bar.
69.Remove 2 bolts securing tie bar to tranmission.
70.Remove tie bar.
71.Remove 2 and slacken 1 bolt, securing bell
housing access plate and position aside.
72.Mark drive plate to torque converter relationship.
73.With assistance, rotate crankshaft for access to
first bolt (torque converter to drive plate).
74.Remove first bolt.
75.Repeat steps for the remaining 3 bolts.
76.Remove 2 bolts securing crankshaft sensor
shield to engine backplate.
See FUEL SYSTEM
SFI, Repair, Crankshaft Position Sensor
(CKP Sensor)

4.0 V8
5
REPAIR 77.Release sensor/shield and remove.
78.Disconnect sensor multiplug.
79.Remove sensor.
80.Remove starter motor heatshield.
See
ELECTRICAL, Repair, Starter Motor
Heatshield - 4.0 V8
81.Disconnect solenoid Lucar.
82.Disconnect RH and LH knock sensor multiplugs.
See FUEL SYSTEM SFI, Repair, Knock
Sensor
83.Release harness from engine.
84.Remove nut securing handbrake cable
heatshield.
85.Release speed sensor lead from clip on
heatshield.
86.Remove heatshield.
87.Disconnect top oil cooler pipe union from
transmission.
88.Release union.
89.Remove 'O' ring and discard.
90.Plug pipe and transmission.
91.Remove bolt securing oil cooler pipe bracket tosump. Collect spacer.
92.Remove 3 bolts from top of bell housing.
93.Collect 2 harness brackets.
94.Remove 2 bolts, LH and RH side of bell housing.
95.Remove centre LH bell housing bolt using long
extension.
96.Remove 2 lower bolts from bell housing.
97.Fit suitable wooden block in access plate hole to
retain torque converter.
98.Secure block with cover plate and tighten one
cover plate bolt.
99.Support gearbox on a jack.
100.Lower ramp.
101.Position lifting chains and attach hooks to engine
lifting eyes.
102.Raise engine.
103.Raise jack.
104.Break engine to gearbox joint.
105.Raise engine.

12ENGINE
6
REPAIR
106.Remove top starter bolt securing engine earth
cable.
107.Remove nut securing kick-down cable clip to LH
cylinder head.
108.With assistance, raise engine, move aside all
pipes and wires. Move engine clear of vehicle.
109.Lower engine onto bench.
Refit
110.Clean engine and gearbox mating faces.
111.Clean dowel and dowel holes.
112.With assistance raise engine off bench. Lower
and guide engine into engine compartment
ensuring no wires or pipes become trapped.
113.Position clip securing kick-down cable to LH
cylinder head.
114.Fit and tighten nut.
115.Position engine earth cable and secure to starter
with top bolt. Tighten to
45 Nm.
116.Lower engine.
117.With assistance, engage engine with gearbox.
118.Fit 3 bottom bell housing bolts. Tighten to
46
Nm.
119.Lower jack supporting gearbox.
120.Lower engine onto mounting brackets.
121.Fit centre RH bell housing bolt.
122.Fit centre LH bell housing bolt.
123.Fit harness brackets to 2 top bell housing bolts.
124.Fit bolts. Tighten to
46 Nm.
125.Remove plugs from tranmission and oil cooler
pipe.
126.Clean pipe, lubricate NEW 'O' ring and fit to
pipe.
127.Connect pipe to transmission and secure with
union. Tighten to
30 Nm.
128.Align pipe bracket to sump, position spacer and
fit bolt. Tighten to
18 Nm.
129.Fit heatshield and secure with nut.
130.Secure transducer lead to clip on heatshield.131.Slacken bell housing access plate bolt.
132.Move plate aside.
133.Remove block.
134.Align drive plate and torque converter.
135.Fit 2 torque converter bolts.
136.Rotate engine and fit second 2 bolts. Tighten to
45 Nm.
137.Rotate engine and tighten first 2 bolts to Tighten
to
45 Nm.
138.Clean cover plate and mating face.
139.Position cover plate and fit bolts. Tighten to
45
Nm.
140.Position access plate.
141.Fit 2 remaining bolts and tighten all bolts to
Tighten to
9 Nm.
142.Position engine harness around engine.
143.Connect knock sensor multiplug.
144.Connect starter solenoid Lucar.
145.Position starter motor heatshield and secure clip
to solenoid.
146.Align shield bracket to engine mounting bracket
and fit bolt. Tighten to
9 Nm.
147.Clean crankshaft sensor mating faces.
148.Position sensor and connect multiplug.
149.Position/align sensor and shield to backplate. Fit
bolts. Tighten to
6 Nm.
150.Fit tie bar, align to transmission and fit bolts.
Tighten to
25 Nm.
151.Fit tie bar securing nut. Tighten to45 Nm.
152.Fit catalytic converter/front pipe assembly.See
EMISSION CONTROL, Repair, Catalytic
Converter/Front Pipe - 4.0 V8
153.Raise engine.
154.Fit RH mounting rubber.
155.Move engine over.
156.Fit LH mounting rubber.
157.Lower engine.
158.Disconnect hoist.
159.Fit engine mounting nuts. Tighten to
55 Nm.
160.Remove plugs from steering pump and steering
box.
161.Clean PAS hose unions.
162.Lubricate 'O' rings and fit to hose unions.
163.Position hose.
164.Align unions to pump and steering box. Tighten
14mm thread to
15 Nm, 16mm thread to
Tighten to
20 Nm.
165.Remove plugs from feed hose and PAS pump.
166.Connect hose to pump and tighten clip.
167.Untie compressor and position to engine
bracket.
168.Position heatshield and fit bolts. Tighten to
25
Nm.
169.Connect compressor multiplug.
170.Position drive belt.

12ENGINE
8
REPAIR
9.Disconnect multiplug from camshaft sensor.
See FUEL SYSTEM SFI, Repair, Camshaft
Position Sensor (CMP Sensor)
10.Remove 9 bolts securing front cover.
11.Remove 2 bolts securing sump to front cover.
12.Loosen 4 bolts securing sump adjacent to front
cover (2 each side).
13.Release front cover assembly.
14.Remove oil seal.
15.Remove and discard gasket.Refit
16.Clean sealant from threads of cover bolts.
17.Clean old sealant from front cover and block joint
face.
CAUTION: Use a plastic scraper.
18.Apply Hylosil jointing compound to gasket
position on cover and block.
19.Fit new gasket to block face.
20.Ensure oil seal register in cover is clean.
21.Lubricate outer face of NEW oil seal.
22.Using LRT-12-089, fit seal to cover.
23.Lubricate oil pump drive gear and position in
pump with groove away from engine.
24.Locate alignment tool LRT-12-090 on front cover
and oil pump drive gear.
25.Position front cover over crankshaft.
26.Press and rotate tool to engage drive gear until
drive gear keyway aligns with Woodruff key.
27.Fit cover to cylinder block.

Mpi
1
DESCRIPTION AND OPERATION DESCRIPTION
The 'T' Series engine is a four cylinder, water cooled
unit comprising a cast iron cylinder block, aluminium
alloy cylinder head and twin aluminium alloy camshaft
carriers.
The cylinder block incorporates direct bored,
siamesed cylinder bores which provide good structural
rigidity. The crankshaft is carried in five main
bearings, end-float being controlled by thrust washers
positioned each side of the centre main bearing.The main bearing caps are located to the cylinder
block by dowels; the bearing shells fitted to Nos. 1, 3
and 5 bearings are fully grooved whilst those fitted to
Nos. 2 and 4 bearings are plain.
The cylinder head carries twin camshafts operating
four valves per cylinder via hydraulic tappets. Both
camshafts are driven by the timing belt and run
directly in journals line bored in the cylinder head and
camshaft carriers. The plastic camshaft covers are
bolted to the camshaft carriers.