wipers LAND ROVER FREELANDER 2001 User Guide

PANEL REPAIRS
REPAIRS 77-2-31
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1.Fit insulation pads to engine bulkhead.
2.Position front carpet and fit treadplate to front
door aperture. 3. Driver's side: Fit clutch pedal box.
4. Driver's side: Fit brake pedal box and brake
servo.
5. Driver's side: Fit passenger compartment fuse
box.
6. LH side: Fit horn.

+ SECURITY, REPAIRS, Horn.
7. LH side: Fit air intake hose.
8. LH side: Fit battery. Do not connect battery
earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
9. LH side: Fit LH engine mounting to body.
10. LH side: Fit front bumper LH support bracket.
11. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
12. RH side: Fit RH engine mounting to body.
13. RH side: Fit front bumper RH support bracket.
14.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
15.Fit PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
16.Fit engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
17.Fit front suspension rear beam.
18.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
19.Fit engine bay shield.
20.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
21.Secure headlamp wiring.
22.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
23.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
24.Fit front bumper armature.
25.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
26.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
27.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
28.Connect all ECUs.
29.Connect alternator.
30.Connect battery earth lead.

PANEL REPAIRS
77-2-32 REPAIRS
Front sidemember (front section)
In this procedure, the front section of the front
sidemember closing panel and the related
crossmember to sidemember gusset plate are
replaced in conjunction with the front sidemember.
Remove
1.Disconnect battery earth lead.
2.Disconnect all ECUs.
3.Remove road wheel(s).
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
6.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
7.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
8.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
9.Release wiring to headlamp and position aside.
10.Remove engine bay shield.
11.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12. LH side: Remove front bumper LH support
bracket.
13. LH side: Remove ECM.
14. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
15. LH side: Remove air cleaner.
16. LH side: Remove air intake hose.
17. LH side: Remove horn.

+ SECURITY, REPAIRS, Horn.
18. RH side: Remove front bumper RH support
bracket.
19. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
20. RH side: Remove alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - KV6.
21. RH side: Remove PAS pump.

+ STEERING, REPAIRS, Pump -
steering - KV6.Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
REPAIRS 77-2-33
Refit
1. LH side: Fit horn.

+ SECURITY, REPAIRS, Horn.
2. LH side: Fit air intake hose.
3. LH side: Fit air cleaner.
4. LH side: Fit battery carrier. Do not connect
battery earth lead.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
5. LH side: Fit ECM.
6. LH side: Fit front bumper LH support bracket.
7. RH side: Fit PAS pump.

+ STEERING, REPAIRS, Pump -
steering - KV6.
8. RH side: Fit alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - KV6.
9. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
10. RH side: Fit front bumper RH support bracket.
11.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12.Fit engine bay shield.
13.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
14. Secure headlamp wiring.
15.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
16.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
17.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
18.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
19.Connect all ECUs.
20.Connect battery earth lead.
Front valance assembly
Remove
1.Disconnect battery earth lead.
2.Disconnect all ECUs.
3.Remove road wheel(s).
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
6.Remove front bumper armature.
7.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
8.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
9.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
10.Release wiring to headlamp and position aside.
11.Remove engine bay shield.
12.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
13.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
14.Remove front suspension rear beam.
15.Remove engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
16.Remove front damper.

+ FRONT SUSPENSION, REPAIRS,
Damper.
17.Remove PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
18.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
19. LH side: Remove front bumper LH support
bracket.
20. LH side: Remove air cleaner.
21. LH side: Remove air intake hose.
22. LH side: Remove ECM.
23. LH side: Remove engine compartment
fusebox.
24. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
25. LH side: Remove engine compartment fuse
box and related wiring.

PANEL REPAIRS
77-2-34 REPAIRS
26. LH side: Remove LH engine mounting from
body.
27. LH side: On models with Diesel engines,
remove fuel filter.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Filter - main - up to 03MY.
28. LH side: Remove LH front brake pipe.
29. RH side: Remove front bumper RH support
bracket.
30. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
31. RH side: Remove coolant expansion tank.
32. RH side: Remove RH engine mounting from
body.
33. RH side: Remove PAS fluid reservoir.
34. RH side: Remove RH front brake pipe.
35. Driver's side: Remove passenger
compartment fuse box.
36.Remove brake pedal box and brake servo.
37.Remove clutch pedal box.
38.Release vehicle harness from valance and
position aside.
39.Remove treadplate from front door aperture.
Release front carpet and position aside.
40.Remove insulation pads from engine bulkhead.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1.Fit insulation pads to front and rear sides of
engine bulkhead.
2.Position front carpet and fit treadplate to front
door aperture.
3.Secure vehicle harness to valance.
4. Driver's side: Fit clutch pedal box.
5.Fit brake pedal box and brake servo.
6.Fit passenger compartment fuse box.
7. LH side: Fit LH front brake pipe. Bleed brake
system.
+ BRAKES, ADJUSTMENTS, Brake
bleed.
8. LH side: On models with Diesel engines, fit fuel
filter.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Filter - main - up to 03MY.
9. LH side: Fit LH engine mounting to body.
10. LH side: Fit engine compartment fuse box and
related wiring.
11. LH side: Fit battery carrier. Do not connect
battery earth lead.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
12. LH side: Fit engine compartment fusebox.
13. LH side: Fit ECM.
14. LH side: Fit air intake hose.
15. LH side: Fit air cleaner.
16. LH side: Fit front bumper LH support bracket.
17. RH side: Fit RH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
18. RH side: Fit PAS fluid reservoir.
19. RH side: Fit RH engine mounting to body.
20. RH side: Fit coolant expansion tank.
21. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
22. RH side: Fit front bumper RH support bracket.
23.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
24.Fit PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
25.Fit front damper.

+ FRONT SUSPENSION, REPAIRS,
Damper.
26.Fit engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
27.Fit front suspension rear beam.
28.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.

PANEL REPAIRS
REPAIRS 77-2-37
Valance front
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
6.Remove engine bay shield.
7.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
8.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
9.Remove front bumper support bracket.
10.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
11.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
12.Release wiring to headlamp and position aside.
13. LH side: Remove air cleaner.
14. LH side: Remove air intake hose.
15. LH side: Remove ECM.
16. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
17. LH side: Remove engine compartment fuse
box and related wiring.
18. LH side: Remove LH front brake pipe.
19. RH side: Remove PAS fluid reservoir.
20. RH side: Remove RH front brake pipe.
21. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
22. RH side: Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
77-2-38 REPAIRS
Refit
1. LH side: Fit LH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
2. LH side: Fit engine compartment fuse box and
related wiring.
3. LH side: Fit battery carrier. Do not connect
battery earth lead.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
4. LH side: Fit ECM.
5. LH side: Fit air intake hose.
6. LH side: Fit air cleaner.
7. RH side: Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
8. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
9. RH side: Fit RH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
10. RH side: Fit PAS fluid reservoir.
11.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
12.Secure headlamp wiring.
13.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
14.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
15.Fit front bumper support bracket.
16.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
17.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
18.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
19.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
20.Connect all ECUs.
21.Connect alternator.
22.Connect battery earth lead.

HEATING AND VENTILATION
80-6REPAIRS
Plenum - air intake
$% 80.15.62
Remove
1.Remove both wiper arms.

+ WIPERS AND WASHERS, REPAIRS,
Arm - wiper - each.
2.Remove 6 studs securing rear edge of air
intake moulding.
3.Remove air intake moulding and bonnet
sealing rubber.
NOTE: Do not carry out further dismantling if
component is removed for access only.
4.Remove bonnet sealing rubber from air intake
moulding.
5.Remove 4 clips securing air intake filter
retainers. Remove retainers and filters.Refit
1.Fit filters and retainers to air intake moulding
and secure with clips.
2.Fit bonnet sealing rubber to air intake moulding.
3.Fit air intake moulding and secure with studs.
4.Fit wiper arms.

+ WIPERS AND WASHERS, REPAIRS,
Arm - wiper - each.

WIPERS AND WASHERS
REPAIRS 84-1
WIPERS AND WASHERS REPAIRS
Reservoir - washer
$% 84.10.01
Remove
1.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
2.Position container to collect fluid loss.
3.Remove 2 nuts securing reservoir filler neck
and remove filler neck.
4.Release both washer pumps from reservoir.
5.Remove and discard pump sealing grommets.
6.Remove 3 bolts securing washer reservoir and
remove.Refit
1.Fit reservoir and secure with bolts.
2.Fit new pump sealing grommets to reservoir.
3.Fit pumps to reservoir.
4.Fit filler neck and secure with nuts.
5.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.

WIPERS AND WASHERS
84-2 REPAIRS
Jet - washer - each
$% 84.10.08
Remove
1.Disconnect tube from washer jet.
2.Depress plastic lugs and remove washer jet
from bonnet.
Refit
1.Fit washer jet to bonnet and connect tube.
2.Adjust jet so the inside spray is to centre of the
screen, and the outer spray is to the top of the
screen.
Pump - washer
$% 84.10.21
Remove
1.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
2.Position container to catch windscreen washer
fluid.
3.Disconnect multiplug and hose from
windscreen washer pump.
4.Release pump from reservoir.
5.Remove and discard pump sealing grommet.
Refit
1.Fit new pump sealing grommet to reservoir.
2.Fit pump to reservoir.
3.Connect hose and multiplug to pump.
4.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.

WIPERS AND WASHERS
REPAIRS 84-3
Arm - wiper - each
$% 84.15.02
Remove
1.Remove nut cover on wiper arm and remove
nut.
2.Remove wiper arm from spindle.
NOTE: Do not carry out further dismantling if
component is removed for access only.
3.Remove wiper blade.

+ WIPERS AND WASHERS, REPAIRS,
Blade - wiper - each.
Refit
1.Fit wiper blade.

+ WIPERS AND WASHERS, REPAIRS,
Blade - wiper - each.
2.Fit wiper arm to spindle, with tip of wiper blade
aligned to screen marks.
3.Fit nut and tighten to 18 Nm (13 lbf.ft).
Blade - wiper - each
$% 84.15.06
Remove
1.Lift wiper arm from screen.
2.Press retaining lever.
3.Slide blade down arm and withdraw.
Refit
1.Position new blade to wiper arm.
2.Push blade into engagement with arm, and
check blade is retained.
3.Lower arm onto screen.