Lexus ES300h 2014 Navigation Manual

130
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select ““WW Off” Function” .
5Select the screen buttons to be turned
off. The selected screen buttons will be
dimmed.
zTo set the setting as a default, select
“Default”.
6Select “OK”.
zThe previous screen will be displayed.
7Select “Save” .
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select “Calibration” .
5Select the desired screen button.
SCREEN LAYOUT FUNCTION
(“WW Off” Function)
Each screen button and current street
name on the map screen can be dis-
played or hidden.CURRENT POSITION/TIRE
CHANGE CALIBRATION
The current position mark can be adjust-
ed manually. Miscalculation of the dis-
tance caused by tire replacement can
also be adjusted.
z For additional information on the accu-
racy of a current position, see “LIMITA-
TIONS OF THE NAVIGATION
SYSTEM” on page 139.

131
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
■POSITION/DIRECTION CALI-
BRATION
1Select “Position / Direction” .
2Select one of the 8 directional screen
buttons to move the cursor to the de-
sired point on the map.
3Select “OK”.
4Select either or to adjust the di-
rection of the current position mark.
5Select “OK”.
zThe map will be displayed.
■ TIRE CHANGE CALIBRATION
1To perform the distance calibration pro-
cedure, select “Tire Change” .
zThe message appears and the quick dis-
tance calibration is automatically started. A
few seconds later, a map will be displayed.
When driving, the cu rrent position mark
will be automatically corrected by GPS
signals. If GPS reception is poor due to
location, the current position mark can
be adjusted manually.
The tire change calibration function will
be used when replacing the tires. This
function will adjust miscalculation
caused by the circumference difference
between the old and new tires.

132
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select “Pop-up Information”.
5Select “On” or “Off” .
6Select “Save” .
zWhen “Pop-up Information” is turned off,
the following messages will not be dis-
played.
X This message appears when the map
scale is over 0.5 miles (800 m).
X This message appears when the map is
switched to dual map screen mode.INFORMATION
●
If this procedure is not performed when
the tires are replaced, the current posi-
tion mark may be incorrectly displayed.
POP-UP INFORMATION
When “Pop-up information” is turned
on, pop-up information will be displayed.

133
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
2. VEHICLE SETTINGS
1Press the “MENU” button on the
Remote Touch.
2Select “Setup” .
3Select “Vehicle” .
4Select “Maintenance” .
5Select the desired screen button.
zSetting maintenance information. (See
page 133.)
z Setting dealer. (See page 135.)
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Vehicle” on the “Setup” screen.
3Select “Maintenance” on the “Vehicle
Settings” screen.
MAINTENANCE
When the navigation system is turned
on, the “Maintenance Reminder” screen
displays when it is time to replace a part
or certain components. (See page 32.)
MAINTENANCE
INFORMATION SETTING

134
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
4Select the desired screen button.
zWhen the vehicle needs to be serviced, the
screen button color will change to orange.
Screen buttonFunction
“Engine oil”Replace engine oil
“Oil filter”Replace engine oil filter
“Rotation”Rotate tires
“Tires”Replace tires
“Battery”Replace 12-volt battery
“Brake pad”Replace brake pads
“Wipers”Replace wiper blades
“Coolant”Replace coolant
“Brake oil”Replace brake fluid
“Trans. fluid”Replace transmission flu-
id
“Service”Scheduled maintenance
“Air filter”Replace air filter
“Personal”
New information items
can be created separately
from provided ones.
“Delete All”
Select to cancel all condi-
tions which have been in-
put.
“Reset All”Select to reset the item
which has satisfied a con-
dition.
“Set Dealer”
Select to register dealer
information. (See “DEAL-
ER SETTING” on page
135.)
“Dealer Info.”Select to edit dealer infor-
mation. (See “DEALER
SETTING” on page 135.)
“Reminder”
When this screen button
is selected, the indicator is
illuminated. The system is
set to give maintenance
information with the
“Maintenance Reminder”
screen. (See page 32.)
Screen buttonFunction

135
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
5Input the conditions.
6Select “OK”.
zThe screen then returns to the “Mainte-
nance” screen.
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Vehicle” on the “Setup” screen.
3Select “Maintenance” on the “Vehicle
Settings” screen.
4Select “Set Dealer”.
5If a dealer has not been registered, enter
the location of a dealer in the same way
as for a destination search. (See “DES-
TINATION SEARCH” on page 68.)
No.Function
Select to input the next maintenance
date.
Select to input the driving distance
until the next maintenance check.
Select to cancel the date and distance
conditions.
Select to reset the date and distance
conditions.
INFORMATION
●
For scheduled mainte nance information,
refer to “Warranty and Services Guide/
Owner’s Manual Supplement/Scheduled
Maintenance”.
●Depending on driving or road conditions,
the actual date and distance maintenance
should be performed may differ from the
stored date and distance in the system.
DEALER SETTING
Dealer information can be registered in
the system. With dealer information reg-
istered, route guidance to the dealer is
available.

136
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
zWhen “Set Dealer” registration is finished,
the “Dealer” screen is displayed.
6Select “Edit” next to the item to be edit-
ed.
■ TO EDIT “Dealer” OR “Contact”
1Select “Edit” next to “Dealer” or “Con-
tact”.
2Enter the name using the alphanumeric
keys.
z Up to 70 characters can be entered for
dealer and 24 characters for contact.
3Select “OK”.
zThe previous screen will be displayed.
No.Function
Select to enter the name of a dealer.
(See page 136.)
Select to enter the name of a dealer
member. (See page 136.)
Select to set the location. (See page
137.)
Select to enter the phone number.
(See page 137.)
Select to delete the dealer informa-
tion displayed on the screen.
Select to set the displayed dealer as a
destination. (See “STARTING
ROUTE GUIDANCE” on page 87.)

137
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
■TO EDIT “Location”
1Select “Edit” next to “Location”.
2Select one of the 8 directional screen
buttons to move the cursor to the de-
sired point on the map screen.
3Select “OK”.
zThe previous screen will be displayed.
■ TO EDIT “Phone #”
(PHONE NUMBER)
1Select “Edit” next to “Phone #”.
2Enter the number using number keys.
3Select “OK”.
zThe previous screen will be displayed.

138
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1Press the “MENU” button on the
Remote Touch. (See “Remote Touch”
on page 10.)
2Select “Setup” on the “Menu” screen.
3Select “Vehicle” on the “Setup” screen.
4Select “Vehicle Customization” .
5Select the desired items to be set.
zFor a list of the settings that can be
changed, refer to “Owner’s Manual”.
6After changing th e settings, select
“Save” . A message indicating that the
settings are being saved will appear. Do
not perform any other operations while
this message is displayed.
VEHICLE CUSTOMIZATION
Vehicle settings can be changed.
CAUTION
●When performing the customization pro-
cedure, ensure that there is sufficient ven-
tilation in the vehicle and surrounding
area. If there is insu fficient ventilation,
exhaust gases may collect and enter the
vehicle. Exhaust gases include harmful
carbon monoxide (CO) and inhaling
them may lead to death or a serious
health hazard.
INFORMATION
●
To avoid discharging the 12-volt battery,
perform the customization procedure
with the engine running <the hybrid sys-
tem operating>.

139
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
5. GPS (GLOBAL POSITIONING SYSTEM)
1. LIMITATIONS OF THE NAVIGATION SYSTEM
The Global Positioning System (GPS) de-
veloped and operated by the U.S. Depart-
ment of Defense provides an accurate
current position, normally using 4 or more
satellites, and in some case 3 satellites. The
GPS system has a certain level of inaccura-
cy. While the navigation system will com-
pensate for this most of the time, occasional
positioning errors of up to 300 ft. (100 m)
can and should be expected. Generally, po-
sition errors will be corrected within a few
seconds. When the vehicle is receiving signals from
satellites, the “GPS” mark appears at the
top left of the screen.
The GPS signal may be physically obstruct-
ed, leading to inaccurate vehicle position on
the map screen. Tunnel
s, tall buildings,
trucks, or even the pl acement of objects on
the instrument panel may obstruct the GPS
signals.
The GPS satellites may not send signals due
to repairs or improvements being made to
them.
Even when the navigation system is receiv-
ing clear GPS signals, the vehicle position
may not be shown accurately or inappropri-
ate route guidance may occur in some cas-
es.
This navigation system calculates the
current position using satellite signals,
various vehicle signals, map data, etc.
However, an accurate position may not
be shown depending on satellite condi-
tions, road configuration, vehicle condi-
tion or other circumstances.
NOTICE
●The installation of window tinting may
obstruct the GPS signals. Most window
tinting contains some metallic content
that will interfere with GPS signal recep-
tion of the antenna in the instrument
panel. We advise against the use of win-
dow tinting on vehicles equipped with
navigation systems.