Lexus ES300h 2014 Navigation Manual

170
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
6Select “Play” to start reading out of the
message. Select “Stop” to stop the func-
tion.
z Select “-” or “+”, turn the “PWR·VOL”
knob, or use the volume switch on the
steering wheel to adjust the message read
out volume.
z The message read out function is available
even while driving.1Select “Reply” .
2Select the screen button corresponding
to the desired message.
3Select “Send” .
zWhile the message is being sent, a sending
message screen is displayed.
4This screen will be displayed if message
delivery fails.
zSelect “Retry” to attempt to send the mes-
sage again or select “Cancel” to cancel.
zWhen the received message is an e-mail
and “Update Message Read Status on
Phone” is set to “On”, “Mark as Unread”
or “Mark as Read” can be selected.
Select “Mark as Unread” to mark mails
that have been read on the Bluetooth
®
phone as unread. Conversely, select
“Mark as Read” to mark mails that have
not been read on the Bluetooth
® phone
as read. (See “MESSAGE SETTINGS”
on page 187.)
z For SMS/MMS, selecting or
pressing the switch on the steering
wheel calls the sender. (See page 164.)
z Select “Reply” to reply to the message.
(See page 170.)
REPLYING (QUICK REPLY)

171
1. PHONE OPERATION
4
PHONE
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1Reply messages can be edited while the
vehicle is parked. Select “Edit”.
2Select the screen bu tton corresponding
to the desired message.
3Select “OK” when editing is completed.
4Select .
1Select “Read” to check the message.
zThe “Messages” screen will be displayed.
z When “Automatic Message Readout” is
set to “On”, the message will be automati-
cally read out. (See “MESSAGE SET-
TINGS” on page 187.)
EDITING REPLY MESSAGESNEW MESSAGE
NOTIFICATION
If “New Message Pop-up” and “New
Message Voice Notification” are set to
“On” , a notification appears on the
screen and a voice notification will be
heard when a new message arrives.
(See “MESSAGE SETTINGS” on page
187.)
z For SMS/MMS, selecting or
pressing the switch on the steering
wheel calls the sender. (See page 164.)
z To check the message later, select
“Ignore” or .

172
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
2. SETUP
1. PHONE SETTINGS
1Press the “MENU” button on the
Remote Touch.
2Select “Setup” .
3Select “Phone” .
4Perform each setting according to the
procedures outlined on the following
pages.
1Select “Phone Sound Settings” .
2Perform each setting according to the
procedures outlined on the following
pages.
3When all settings are completed, select
“Save”.
The phonebook can be edited. Volume,
display and message settings can also
be changed.
PHONE SOUND SETTINGS
The call and ring tone volume can be ad-
justed. A ring tone can be selected.

173
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
4
PHONE
1Select “Call Volume” on the “Phone
Sound Settings” screen.
2Select “-” or “+” to adjust the call vol-
ume.
3Select “OK”.
1Select “Ring Tone Volume” on the
“Phone Sound Settings” screen.
2Select “-” or “+” to adjust the ring tone
volume.
3Select “OK”.
1Select “Ring Tone” on the “Phone
Sound Settings” screen.
2Select the screen button corresponding
to the desired ring tone.
z Ring tones can be heard by selecting the
screen buttons.
3Select “OK”.
1Select “Default” on the “Phone Sound
Settings” screen.
2Select “Yes”.
INFORMATION
●
The system will automatically increase
the volume when the speed exceeds 50
mph (80 km/h).
CALL VOLUME SETTING
RING TONE VOLUME
SETTING
RING TONE SETTING
INITIALIZING THE SETTINGS
The settings can be initialized.

174
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1Press the “MENU” button on the
Remote Touch. (See “Remote Touch”
on page 10.)
2Select “Setup” on the “Menu” screen.
3Select “Phone” on the “Setup” screen.
4Select “Phonebook” .
5Perform each setting according to the
procedures outlined on the following
pages.
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Phone” on the “Setup” screen.
3Select “Phonebook” on the “Phone Set-
tings” screen.
4Select “Manage Contacts” .
5Perform each setting according to the
procedures outlined on the following
pages.
PHONEBOOK
The call history can be deleted and
phonebook and speed dial settings can
be changed.
INFORMATION
●
Phonebook data is managed indepen-
dently for every registered phone. When
one phone is connected, another phone’s
registered data cannot be read.
SETTING THE PHONEBOOK
The phonebook can be transferred from
a Bluetooth
® phone to the system. The
phonebook also can be added, edited
and deleted.

175
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
4
PHONE
■THE “Contacts” SCREEN CAN
ALSO BE DISPLAYED
1Press the “MENU” button on the
Remote Touch, then select “Phone”.
zThe “Phone” screen can be displayed by
pressing
on the steering wheel.
2Select “Contacts” on the “Phone”
screen.
3Select “Options” .
4Select “Manage Contacts” .
■TRANSFERRING A PHONE NUM-
BER
X For PBAP compatible Bluetooth®
phones
1Select “Transfer Contacts” .
2Select “Update Contacts” .
The phone numbers in a Bluetooth®
phone can be transferred to the system.
The system can manage up to 5 phone-
books. Up to 1000 contacts (maximum
of 3 numbers per contact) can be regis-
tered in each phonebook.
Operation methods differ between
PBAP compatible and PBAP incompat-
ible but OPP compatible Bluetooth
®
phones.
If your cellular phone is neither PBAP
nor OPP compatible, the phonebook
cannot be transferred.

176
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3Transfer the phonebook data to the sys-
tem using the Bluetooth
® phone.
zThis operation may be unnecessary
depending on the cellular phone model.
z Depending on the type of cellular phone,
OBEX authentication may be required
when transferring phonebook data. Enter
“1234” into the Bluetooth
® phone.
z This screen appears while transferring. To
cancel this function, select “Cancel” .
z If another Bluetooth
® device is connected
when transferring phonebook data,
depending on the phone, the connected
Bluetooth
® device may need to be discon-
nected.
X PBAP compatible models automatic
data transfer setting
1Select “Transfer Contacts” .
2Select “Automatically Download Con-
tacts” to transfer the phonebook from a
connected cellular phone.
Select “Automatically Download Call
History” to transfer the call history from
a connected cellular phone.
3Select “On”.
4Select “Save” .
When a PBAP compatible phone is con-
nected, the phone’s phonebook data can
be automatically transferred.

177
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
4
PHONE
XFor PBAP incompatible but OPP com-
patible Bluetooth® phones
1Select “Transfer Contacts” .
2Select “Replace Contacts” or “A d d
Contacts” .
zIf the phonebook contains phonebook
data, this screen is displayed.
3Transfer the phonebook data to the sys-
tem using a Bluetooth
® phone.
zDepending on the type of cellular phone,
OBEX authentication may be required
when transferring phonebook data. Enter
“1234” into the Bluetooth
® phone.
z This screen appears while transferring. To
cancel this function, select “Cancel”. If
“Add Contacts” is selected and there is an
interruption during the transfer of data, the
phonebook data transferred until then will
be stored in the system. This is not the case
when “Cancel” is selected.
4When the transfer is complete, “Done”
will appear on the screen. Select
“Done”.
X When another Bluetooth
® device is con-
nected
z When another Bluetooth® device is cur-
rently connected, this screen is displayed.
z To disconnect it, select “Yes” .
INFORMATION
●
Depending on the type of Bluetooth®
phone, the registered image on the
phonebook may not appear when
phonebook data is transferred.

178
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
XFrom “Contacts” screen
1Press the “MENU” button on the
Remote Touch, then select “Phone”.
zThe “Phone” screen can be displayed by
pressing
on the steering wheel.
2Select “Contacts” on the “Phone”
screen.
3Select “Transfer” .
4This screen is displayed. The following
operations are performed in the same
manner as when they are performed
from the “Setup” screen.
■REGISTERING THE PHONE-
BOOK DATA
1Select “New Contact” .
2Use the software keyboard to input the
name and select “OK” .
3Input the phone number and select
“OK”.
zTo use a tone signal after the phone num-
ber, input the tone signal too.
Phonebooks of PBAP incompatible but
OPP compatible phones can also be
transferred from the “Contacts” screen.
The phonebook data can be registered.
Up to 3 numbers per person can be reg-
istered. New phonebook data cannot be
added for PBAP compatible
Bluetooth
® phones.

179
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
4
PHONE
4Select the phone type.
5When 2 or less numbers in total are reg-
istered to this contact, this screen is dis-
played.
z To add a number to this contact, select
“Yes” .
■EDITING THE PHONEBOOK
DATA
1Select “Edit Contacts” .
2Select the desired data to edit.
3Select the desired name or number.
4Edit the name or the number. (See
“REGISTERING THE PHONEBOOK
DATA” on page 178.)
5Select “Save” when editing is complet-
ed.
The phone number can be registered in
“Phone # 1” , “Phone # 2” and “Phone #
3” separately. Phonebooks cannot be
edited for PBAP compatible
Bluetooth
® phones via the navigation
system.