navigation Lexus GS350 2014 Navigation manual

169
4. MY MEMORY
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
NAVIGATION SYSTEM
3
2Open the cover and connect a USB
memory.
zTurn on the power of the USB memory if it
is not turned on.
3Display the “My memory” screen.
(→ P.152)
4Select “Backup to USB” .
5Select “Start backup” .
“Set password” : Select to set a password.
( → P.170)
6Enter the password and select “OK”.
7Check that a progress bar is being dis-
played while the data backup is in
progress.
zTo cancel this function, select “Cancel”.
8Check that a confirmation screen is dis-
played when the operation is complete.
INFORMATION
●
In the following situations, the memory
point cannot be backed up to a USB
memory:
• When the memory point was registered using “UK Postal code” or “NL Postal
code”
• When the memory point was registered using connected service
GS_Navi+MM_OM30E40E_(EE).book Page 169 Thursday, July 24, 201 4 3:57 PM

170
4. MY MEMORY
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
1Select “Set password” .
2Enter a password and select “OK”.
3For confirmation, re-enter the pass-
word.
1Display the “My memory” screen.
(→ P.152)
2Select “Copy from USB” .
zIf a password has already been set, enter
the password. For instructions on setting a
password: →P.1 7 0
z If there are multiple memory points stored
on the USB memory, select the memory
points to be copied and select “Start”.
3Check that a progress bar is being dis-
played while the data copy is in
progress.
zTo cancel this function, select “Cancel”.
4Check that a confirmation screen is dis-
played when the operation is complete.
SETTING PASSWORD
Once a password has been set, it will be
requested not only to back up data, but
also when copying memory points from
a USB memory to the navigation system.
INFORMATION
●
If you have forgotten the password:
• It is necessary to initialize personal data using “Delete personal data” . (→ P. 8 4 )
• Contact any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
COPYING FROM A USB
MEMORY
Memory points that have been backed
up can be downloaded to the navigation
system using a USB memory.
To use this function, it is necessary to
connect a USB memory to the system.
(→ P.168)
GS_Navi+MM_OM30E40E_(EE).book Page 170 Thursday, July 24, 201 4 3:57 PM

171
4. MY MEMORY
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
NAVIGATION SYSTEM
3
INFORMATION
●
Memory points that are located outside
of the map’s data range cannot be regis-
tered.
●A maximum of 500 memory points can
be registered.
●When there are 21 or more memory
points stored on a USB memory, only 20
memory points will be displayed at a time.
●If memory points which have the same
name are already stored in the navigation
system, the system may not update those
memory points.
GS_Navi+MM_OM30E40E_(EE).book Page 171 Thursday, July 24, 201 4 3:57 PM

172
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
5. SETUP
1. NAVIGATION SETTINGS
1Press the “MENU” button on the
Remote Touch.
2Select “Setup” .
3Select “Navigation” .
4Select the items to be set.
GS_Navi+MM_OM30E40E_(EE).book Page 172 Thursday, July 24, 201 4 3:57 PM

173
5. SETUP
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
NAVIGATION SYSTEM
3
NAVIGATION SETTINGS
SCREEN
No.FunctionPage
Detailed connected service
settings can be changed.413
Select to set the average
vehicle speed.174
Select to set displayed POI
icon categories.174
Select to set display of 3D
landmarks on/off.
Select to set speed limit in-
formation on/off.
Select to set the automatic
zooming function on/off.
(When the vehicle ap-
proaches a guidance point)

Select to set display of cau-
tionary messages on/off.
(e.g., When the route in-
cludes traffic restrictions or
seasonally restricted
roads.)

Select to set display of pop-
up messages on/off.
Select to adjust the current
position mark manually.
Miscalculation of the dis-
tance caused by tyre re-
placement can also be
adjusted.
175
Coverage areas and legal
information can be dis-
played.189
Select to reset all setup
items.
No.FunctionPage
GS_Navi+MM_OM30E40E_(EE).book Page 173 Thursday, July 24, 2014 3:57 PM

174
5. SETUP
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
1Display the “Navigation settings”
screen. (→P.172)
2Select “Average speed” .
3Select “” or “” to set the average ve-
hicle speeds.
“Default” : Select to set the default speeds.
“Consider traffic info” : Select to set use set-
tings based on traffic information.
1Display the “Navigation settings”
screen. ( →P.172)
2Select “Select POI icons” .
3Select the category to be changed.
“Default” : Select to set the default catego-
ries.
4Select the desired category.
“List all categories” : Select to display all
POI categories.
5Select the desired POI icon.
AVERAGE SPEED
The speed that is used for the calculation
of the estimated travel time and estimat-
ed arrival time can be set.
INFORMATION
●
The displayed time to the destination is
the approximate driving time that is cal-
culated based on the selected speeds
and the actual position along the guid-
ance route.
●The time shown on the screen may vary
greatly depending on progress along the
route, which may be affected by condi-
tions such as traffic jams and construction
work.
POI CATEGORY CHANGE
(SELECT POI ICONS)
Up to 6 POI icons, which are used for
selecting POIs on the map screen, can
be selected as favourites.
GS_Navi+MM_OM30E40E_(EE).book Page 174 Thursday, July 24, 201 4 3:57 PM

175
5. SETUP
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
NAVIGATION SYSTEM
3
1Display the “Navigation settings”
screen. (→P.172)
2Select “Calibration” .
3Select the desired item.
■POSITION/DIRECTION CALI-
BRATION
1Select “Position / Direction” .
2Scroll the map to the desired point
(→ P.105) and select “OK”.
3Select an arrow to adjust the direction of
the current position mark and select
“OK”.
CURRENT POSITION/TYRE
CHANGE CALIBRATION
The current position mark can be adjust-
ed manually. Miscalculation of the dis-
tance caused by tyre replacement can
also be adjusted.
z For additional information on the accu-
racy of a current position: →P.1 8 6
When driving, the current position mark
will be automatically corrected by GPS
signals. If GPS reception is poor due to
location, the current position mark can
be adjusted manually.
GS_Navi+MM_OM30E40E_(EE).book Page 175 Thursday, July 24, 201 4 3:57 PM

177
5. SETUP
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
NAVIGATION SYSTEM
3
2. TRAFFIC AND PARKING SETTINGS
1Press the “MENU” button on the
Remote Touch.
2Select “Setup” .
3Select “Info”.
4Select “Traffic” or “Parking” .
5Select the items to be set.
Settings are available for displaying traf-
fic information icons, receivable traffic
stations, parking information icons etc.
GS_Navi+MM_OM30E40E_(EE).book Page 177 Thursday, July 24, 201 4 3:57 PM

179
5. SETUP
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
NAVIGATION SYSTEM
3
1Display the “Traffic info settings” screen.
(→ P.177)
2Select “Show traffic info” .
3Select the desired icons to be displayed
on the map screen.
“A l l o n ” : Select to select all icons in the traffic
information.
“A l l o f f ” : Select to cancel all the selections.
Traffic information can set
to be received automatical-
ly, or to receive RDS-TMC
traffic information only.
184
Select to set display of
parking icons on the map
screen on/off.
Select to receive parking
lot information.184
Select to enable the roam-
ing function of parking lot
information.185
Select to reset all setup
items.
No.FunctionPageSHOW TRAFFIC INFO
zFor more details on traffic information
icons: →P.111
GS_Navi+MM_OM30E40E_(EE).book Page 179 Thursday, July 24, 201 4 3:57 PM

180
5. SETUP
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
1Display the “Traffic info settings” screen.
(→ P.177)
2Select “Avoid traffic events” .
3Select the desired item.
■CHANGING THE ROUTE MANU-
ALLY
1Select the desired item.
AVOID TRAFFIC EVENTS
No.Function
Select to automatically change
routes when traffic information of the
guidance route has been received.
Select to select manually whether or
not to change routes when traffic in-
formation of the guidance route has
been received. In this mode, a screen
will appear to ask if you wish to re-
route. ( →P.180)
Select to not reroute when traffic in-
formation for the guidance route has
been received.
When the navigation system calculates
a new route, the following screen will be
displayed.
No.Function
Select to start route guidance using
the new route.
Select to confirm the new route and
current route on the map screen.
“New route” or “Old route” can be
selected.
Select to continue the current route
guidance.
GS_Navi+MM_OM30E40E_(EE).book Page 180 Thursday, July 24, 201 4 3:57 PM