Lexus HS250h 2012 Navigation Manual

TELEPHONE AND INFORMATION
140
FCC ID : AJDK021
IC : 775E−K02 1
This device complies with Part 15 of the
FCC Rules and RSS −Gen and
RSS− 210 of IC Rules. Operation is sub-
ject to the following two conditions : (1)
This device may not cause harmful inter-
ference, and (2) this device must accept
any interference received, including in-
terference that may cause undesired
operation.
CAUTION
FCC WARNING: Changes or modifi-
cations not expressly approved by
the party responsible for compliance
could void the user’s authority to op-
erate the equipment.
CAUTION: Radio Frequency Radi-
ation Exposure
This equipment complies with FCC
radiation exposure limits set forth for
uncontrolled equipment and meets
the FCC radio frequency (RF) Expo-
sure Guidelines in Supplement C to
OET65. This equipment has very low
levels of RF energy that it deemed to
comply without maximum permis-
sive exposure evaluation (MPE). But
it is desirable that it should be
installed and operated with at least 20
cm and more between the radiator
and person’s body (excluding ex-
tremities: hands, wrists, feet and
ankles).
Co− location: This transmitter must
not be co−located or operated in con-
junction with any other antenna or
transmitter.
To use the hands− free system, you
need to enter your phone into the sys-
tem. Once you have registered it, you
can make a hands −free call.
If you haven’t yet registered any
Bluetooth rphones, you must first register
your phone according to the following
procedure.
Please see “ DRegistering a Bluetooth r
phone” on page 337 of additional registra-
tion when registering.
U0002AASLY
1. Push the “MENU” button on the Re-
mote Touch.
2. Select “Info./Phone”.
11 08.03HS250h_NAVI_U
7505 1U
— Enter a Bluetooth rphone

TELEPHONE AND INFORMATION
141
3. Select “Phone”.
U5002LC
4. Select “Yes” to connect your phone.
U5010LI
5. When this screen is displayed, input
the passcode displayed on the screen
into the phone.
For the operation of the phone, see the
manual that comes with your cellular
phone.
If you want to cancel it, select“Cancel”.
U5011LI
6. When the connection is completed,
this screen is displayed.
You do not need to enter the phone in case
of using the same one.
U5012LI
When this screen is displayed, follow the
guidance on the screen to try again.
1108.03HS250h_NAVI_U
7505 1U
5

TELEPHONE AND INFORMATION
142
D
Connecting a Bluetooth
rphone
AUTOMATICALLY
U5006LC
When you register your phone, auto
connection will be turned on. Always
set it to this mode and leave the
Bluetooth rphone in a condition where
connection can be established.
U5007LC
When the “POWER” switch is in AC-
CESSORY or ON mode, a nearby cellu-
lar phone you have registered is
searched for.
Next, the system automatically con-
nects with the latest of the phones con-
nected to in the past.
Then, the connection result is dis-
played.
This screen appears when the Bluetooth r
phone is first connected after the “POW-
ER” switch is in ACCESSORY or ON
mode.
INFORMATION
It may take time, the phone connec-
tion is carried out during Bluetooth r
audio play.
11 08.03HS250h_NAVI_U
7505 1U

TELEPHONE AND INFORMATION
143
MANUALLY
When the auto connection has failed or
“Handsfree power” is turned off, you
have to connect Bluetoothrmanually.
1. Push the “MENU” button on the Re-
mote Touch, then select “Info./Phone”.
2. Select “Phone”.
U5008LC
3. Select “Connect Phone”.
U5009LC
4. Select “Handsfree Power”, or select
the phone to connect.
U5010LC
5. The “Connect Bluetooth∗” screen is
displayed.
U5011LC
6. When the connection is completed,
this screen is displayed.
Now you can use the Bluetooth rphone.
∗: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
11 08.03HS250h_NAVI_U
7505 1U
5

TELEPHONE AND INFORMATION
144
When you connect the phone while
Bluetoothraudio is playing
U5012LC
This screen is displayed, and the
Bluetooth raudio will stop temporarily.
DReconnecting the Bluetooth rphone
If the Bluetooth rphone is
disconnected with a poor reception
from the Bluetooth rnetwork when the
“POWER” switch is in ACCESSORY or
ON mode, the system automatically
reconnects the Bluetooth rphone. In
this case, the connection result is not
displayed.
If the Bluetooth ris disconnected on pur-
pose such as you turned your cellular
phone off, this does not happen. Recon-
nect it by the following methods.
DSelect the Bluetooth rphone again.
DEnter the Bluetooth rphone.
11 08.03HS250h_NAVI_U
7505 1U

TELEPHONE AND INFORMATION
145
After you enter the Bluetoothrphone,
you can call by using hands− free sys-
tem. You can call using the 6 methods
described below.
DBy dial
You can call by inputting the phone
number.
This cannot be operated while driving.
1. Push the “MENU” button on the Re-
mote Touch. (See “—Remote Touch”
on page 10.)
2. Select “Info./Phone”.
You can also push
of the steering
wheel to display the “Phone” screen.
3. Select “Phone”.
U5014LC
4. Select the desired key to input the
phone number.
Each time you select
, an inputted
digit is deleted.
When you select “Redial”, the number
you called last is inputted.
Select
or pushof the steering
wheel.
11 08.03HS250h_NAVI_U
7505 1U
— Call on the Bluetooth r
phone
5

TELEPHONE AND INFORMATION
146
D
By phonebook
You can call by phonebook data which
is transferred from your cellular phone.
The system has one phonebook for
each telephone. You can register up to
1000 numbers in total of phonebooks.
This cannot be operated while driving.
U5016LC
1. Select “Contacts”.
U5017LC
2. Select the desired data from the list.
U5018LC
3. Select the desired number from the
list.
Select
or pushof the steering
wheel.
11 08.03HS250h_NAVI_U
7505 1U

TELEPHONE AND INFORMATION
147
When the phonebook is empty
U5019LC
1. Select “Contacts”.
U5020LC
2. Select “Yes” if you want to transfer
new contacts from a cellular phone.
Select “No” if you want to edit the
phonebook.
DBy speed dial
You can call using registered phone
numbers which can be selected from a
phonebook. (See “ DRegistering the
speed dial” on page 354 for registering
the speed dial.)
This can be done while driving.
U5021LC
1. Select “Speed Dials”.
U5022LC
2. Select the desired number to call.
You can change the page by selecting
“Speed Dial 2” or “Speed Dial 3” tab.
11 08.03HS250h_NAVI_U
7505 1U
5

TELEPHONE AND INFORMATION
148
D
By call history
You can call by call history which has 4
functions below.
“All”: all the numbers above which
were memorized
“Missed”: calls which you missed
“Incoming”: calls which you received
“Outgoing”: numbers which you called
You can call using the latest 5 call history
items shown by “All”while driving.
U5023LC
1. Select “Call History”.
U5024LC
2. Select the desired data from the list.
When the list is switched, select “All”,
“Missed”, “Incoming” or “Outgoing” tab.
U5025LC
3. Selector pushof the steer-
ing wheel.
11 08.03HS250h_NAVI_U
7505 1U

TELEPHONE AND INFORMATION
149
You can call using the latest call history
item.
1. Push
of the steering wheel to dis-
play the “Phone” screen.
2. Push
of the steering wheel to dis-
play the “Call History” screen.
3. Push
of the steering wheel to se-
lect the latest history item.
4. Select
or pushof the steer-
ing wheel to call the latest history item.
DWhen you call by phonebook, the
name (if registered) is displayed.
DWhen you call the same number
continuously, only the newest number is registered.
DWhen a phone number registered in
the phonebook is received, the name and the number are displayed.
DUnnoticed phone number such as a
public phone is not memorized in the system.
DA international phone call may not be
made depending on the cellular phone which you have.
DBy voice recognition
U5009LI
You can call by giving a command. (For
the operation and command of voice
recognition, see “Voice command sys-
tem” on page 51.)
This can be operated while driving.
The “Dial by Name” operating procedure is
explained here.
Other operating procedures are also simi-
lar.
11 08.03HS250h_NAVI_U
7505 1U
5