display Lexus IS250 2014 Navigation Manual

277
1. SPEECH COMMAND SYSTEM OPERATION
SPEECH COMMAND SYSTEM
IS300h/250_Navi_EE
5
1Press the talk switch.
2Say “Go home” or select “Go home”.
zA confirmation screen will be displayed
showing the recognition results.
3Say “Yes” or select “Yes”.
zThe system starts searching for a route to
your home.
zWhen the speech command is recognized,
the map of the area around the home
address will be displayed and route guid-
ance to the home address will begin.
INFORMATION
●
If the system does not respond or the
confirmation screen does not disappear,
press the talk switch and try again.
●If a speech command cannot be recog-
nized, voice guidance will say “Pardon?”
and speech command reception will
restart.
●If a speech command cannot be recog-
nized 2 consecutive times, the speech
command guidance system will say “To
restart voice recognition, push the talk
switch.”. Then voice recognition will be
suspended.
●The voice recognition prompt can be set
to on or off when “Voice prompts” is
selected. This setting can also be
changed on the “Voice settings” screen.
(→P. 8 4 )
●Voice guidance can be canceled by set-
ting voice prompts to off. Use this setting
when it is desirable to say a command
immediately after pressing the talk switch
and hearing a beep.
SPEECH COMMAND
EXAMPLE: SEARCHING FOR
A ROUTE TO YOUR HOME*
zIf a home address is not registered, voice
guidance will say “Your home is not set.”.
Please try again after setting a home
location. (→P.151)
*: With navigation function
IS_Navi_EE_53C71E.book 277 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

278
1. SPEECH COMMAND SYSTEM OPERATION
IS300h/250_Navi_EE
1Press the talk switch.
2Say “Enter an address” or select “Enter
an address”.
zThe searchable countries are restricted
according to the voice recognition lan-
guage.
zSome areas cannot be recognized by the
voice recognition system.
XFor UK English and French
3Say “<house number>”, “<street name>”
and “<city name>” continuously.
XExcept for UK English and French
3Say “<street name>”, “<house number>”
and “<city name>” continuously.
zSay the desired house number in the place
of the “<>”. It is possible to only say the num-
bers. For example, 1,2,3,4 etc. (It is not pos-
sible to say cardinals.) Inputting the house
number can be skipped.
zSay the desired full street name that
belongs to the set country in the place of
the “<>”. If only the city name was said at
step 3, say the street name. If the street
name is not unique, select the appropriate
number from the displayed address list.
zSay the desired city name or city name and
street name that belongs to the set country
in the place of the “<>”. Not just the city
name, but the city name and street name
can be said at the same time. If both are
said at the same time and the street name is
not unique, select the appropriate number
from the displayed address list.
SPEECH COMMAND
EXAMPLE: PERFORMING A
DESTINATION SEARCH BY
ADDRESS*
Use the official language of the country
the desired destination is in. A destina-
tion search by address, using speech
command, can only be performed for
countries that have one of the following
15 languages as their official language.
· Dutch
· French
· German
· Italian
· Spanish
· UK English
· Russian
· Portuguese
· Swedish
· Danish
· Finnish
· Greek
· Polish
· Turkish
· Czech
For changing voice recognition lan-
guages: →P.75
*: With navigation function
IS_Navi_EE_53C71E.book 278 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

279
1. SPEECH COMMAND SYSTEM OPERATION
SPEECH COMMAND SYSTEM
IS300h/250_Navi_EE
5
4Say or select “Enter”.
zA map corresponding to the decided
address is displayed. To set the displayed
point as a destination, say “Enter”.
zIf multiple points exist, the next point can be
displayed by saying “Next”.
1Press the talk switch.
z“Play artist <name>”, “Play album <name>”,
“Play song <name>” and “Play playlist
<name>” are displayed in the “Shortcuts”
screen.
2Say or select “Play artist <name>”, “Play
album <name>”, “Play song <name>” or
“Play playlist <name>”.
zSay the desired name in the place of the
“<>”.
zA confirmation screen will be displayed
showing the recognition results. If multiple
matching items are found, a selection
screen will be displayed.
3Say “Play” or select “Play”.
zThe system starts playing music.
INFORMATION
●
To change the country to be searched,
say “Change country” when the screen to
say the city name is displayed and the
screen will change to the country input
screen.
●The house number voice recognition
conditions are outlined below:
• Numerals: 10 digits or less
• Cardinals cannot be recognized.
• Numerals are recognized as single dig-
its only.
SPEECH COMMAND
EXAMPLE: SEARCH FOR A
TRACK
IS_Navi_EE_53C71E.book 279 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

280
1. SPEECH COMMAND SYSTEM OPERATION
IS300h/250_Navi_EE
1Press the talk switch.
z“Call <name>” is displayed in the
“Shortcuts” screen.
zWhen “Call <name>” on the “Shortcuts”
screen is dimmed, the contact’s speech
command recognition cannot be used.
Check the Bluetooth
® connection and if
the contacts have been transferred to the
system.
2Say or select a registered contact name.
zIn the same manner as it is displayed on the
screen, “Call <name>”, after saying
“Call”
say the name of a contact.
For example: “Call”, “J o h n S m i t h”
zShort or abbreviated names in the contact
list may not be recognized. Change names
in the contact list to full names.
zSometimes a voice recognition result con-
firmation screen will be displayed. After
confirming the result, say “Dial”.
zWhen the system recognizes multiple
names from the contact list, a name candi-
date list will be displayed on the screen. If
the desired name is not displayed on the
top of the screen, say the number of the
name from the candidate list to select a
name from the candidate list.
INFORMATION
●
A USB memory or iPod must be con-
nected to enable track searching and
playback. (→P.222, 229)
●When a USB memory or iPod is con-
nected, recognition data is created so
tracks can be searched using speech
commands.
●Recognition data is updated under the
following conditions:
• When the USB memory or iPod data
has changed.
• When the voice recognition language is
changed. (→P. 7 5 )
●While the recognition data is being cre-
ated or being updated, a track search
cannot be performed using a speech
command.
●When “Play music” is dimmed in the
“Shortcuts” screen, it is not possible to
search for a track using a speech com-
mand. In this situation, reduce the amount
of music data in the USB memory or iPod
and update the recognition data to
enable searching by speech command.
SPEECH COMMAND
EXAMPLE: CALL NAME
IS_Navi_EE_53C71E.book 280 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

281
1. SPEECH COMMAND SYSTEM OPERATION
SPEECH COMMAND SYSTEM
IS300h/250_Navi_EE
5
zWhen a contact has multiple telephone
numbers registered in the contact list, a
candidate list will be displayed. If the
desired telephone number is not displayed
on the top of the screen, say the number of
the desired telephone number from the
candidate list to select a telephone number
from the candidate list.
3Say or select “Dial” to call the telephone
number.
1Press the talk switch.
z“Dial <number>” is displayed in the
“Shortcuts” screen.
zWhen “Dial <number>” on the “Shortcuts”
screen is dimmed, the telephone number
voice recognition cannot be used. Check
the Bluetooth
® phone connection.
2Say the telephone number.
zIn the same manner as it is displayed on the
screen, “Dial <number>”, after saying “Dial”
say the telephone number.
zSay the telephone number one digit at a
time.
For example, if the telephone number is
2345678:
Say “two three four five six seven eight”
zAs the system cannot recognize additional
numbers, say the complete number without
stopping.
zWhen the system recognizes multiple tele-
phone numbers, a telephone number can-
didate list will be displayed on the screen. If
the desired telephone number is not dis-
played on the top of the screen, say the
number of the desired telephone number
from the candidate list to select a telephone
number from the candidate list.
3Say or select “Dial” to call the telephone
number.
SPEECH COMMAND
EXAMPLE: DIAL NUMBER
IS_Navi_EE_53C71E.book 281 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

282
1. SPEECH COMMAND SYSTEM OPERATION
IS300h/250_Navi_EE
2. COMMAND LIST
zFrequently used commands are listed in the following tables.
zFor devices that are not installed in the vehicle, the related commands will not be dis-
played in the “Shortcuts” screen. Also, according to conditions, other commands may
not be displayed in the “Shortcuts” screen.
zThe functions available may vary according to the system installed.
zCommands that have “O” in the shortcuts menu column can be recognized from the
“Shortcuts” screen.
XBasic
XNavi*
1
*1: With navigation function
*2: For example; “Restaurant”, “Hospital” etc.
Recognizable speech commands and their actions are shown below.
zVoice recognition language can be changed. (→P. 7 5 )
CommandAction
“Help”Prompts voice guidance to offer examples of commands
and operation methods
“Go back”Returns to the previous screen
CommandActionShortcuts
menu
“Find nearby <POI category>”Displays a list of <POI category*2> near the cur-
rent positionO
“Enter an address”Enables setting a destination by saying the ad-
dressO
“Go home”Displays the route to homeO
IS_Navi_EE_53C71E.book 282 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

284
IS300h/250_Navi_EE1. LEXUS PARKING ASSIST
MONITOR ............................................. 286
DRIVING PRECAUTIONS .............................. 286
SCREEN DISPLAY ............................................... 288
USING THE SYSTEM WHEN
PERPENDICULAR PARKING.................... 289
USING THE SYSTEM WHEN
PARALLEL PARKING..................................... 290
SWITCHING THE PARKING MODE
SCREEN.................................................................... 291
2. PERPENDICULAR PARKING
(ESTIMATED COURSE LINE
DISPLAY MODE) ................................ 292
SCREEN DESCRIPTION .................................. 292
PARKING .................................................................. 293
1LEXUS PARKING ASSIST
MONITOR
IS_Navi_EE_53C71E.book 284 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

6
285
IS300h/250_Navi_EE
6 2
1
3
4
5
7
8
3. PERPENDICULAR PARKING
(PARKING ASSIST GUIDE LINE
DISPLAY MODE)................................ 294
SCREEN DESCRIPTION ................................... 294
PARKING ................................................................... 295
4. PARALLEL PARKING .......................... 296
VEHICLE MOVEMENT
PROCEDURE ...................................................... 296
PARKING ................................................................... 297
NARROW MODE ................................................ 302
5. LEXUS PARKING ASSIST
MONITOR
PRECAUTIONS................................... 304
AREA DISPLAYED ON SCREEN................ 304
THE CAMERA ........................................................ 305
DIFFERENCES BETWEEN
THE SCREEN AND
THE ACTUAL ROAD...................................... 306
WHEN APPROACHING
THREE-DIMENSIONAL OBJECTS ........ 308
6. THINGS YOU SHOULD KNOW ..... 310
IF YOU NOTICE ANY SYMPTOMS ........... 310
1. LEXUS PARKING
ASSIST-SENSOR .................................. 312
TYPES OF SENSORS ........................................... 312
LEXUS PARKING ASSIST-SENSOR
SWITCH.................................................................... 312
DISPLAY ...................................................................... 313
THE DISTANCE DISPLAY AND
BUZZER ................................................................... 314
DETECTION RANGE OF
THE SENSORS ..................................................... 315
SENSOR DETECTION
INFORMATION................................................... 315
LEXUS PARKING ASSIST-SENSOR
FAILURE WARNING ........................................ 317
2. LEXUS PARKING ASSIST
SETTING .................................................. 319
SETTING AN ALERT VOLUME ................... 320
SETTING A PARKING SONAR
DISPLAY ................................................................ 320
SETTING A DISPLAY AND
TONE INDICATION ......................................... 321
2LEXUS PARKING ASSIST-
SENSOR
PERIPHERAL MONITORING SYSTEM
IS_Navi_EE_53C71E.book 285 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

286
IS300h/250_Navi_EE
1. LEXUS PARKING ASSIST MONITOR
1. LEXUS PARKING ASSIST MONITOR*
The parking assist monitor assists the
driver by displaying an image of the view
behind the vehicle while backing up, for
example while parking.
The parking assist monitor assists with
the following 2 backing-up operations:
(1) Perpendicular parking (parking in a
garage, etc.)
(2) Parallel parking (parking at the side
of the road, etc.)
INFORMATION
●The screen illustrations used in this text
are intended as examples, and may differ
from the image that is actually displayed
on the screen.
*: If equipped
DRIVING PRECAUTIONS
The parking assist monitor is a supple-
mental device intended to assist the
driver when backing up. When backing
up, be sure to visually check all around
the vehicle both directly and using the
mirrors before proceeding. If you do
not, you may hit another vehicle, and
could possibly cause an accident.
Pay attention to the following precau-
tions when using the parking assist mon-
itor.
CAUTION
●Never depend on the parking assist mon-
itor entirely when backing up. The image
and the position of the guide lines dis-
played on the screen may differ from the
actual state.
Use caution, just as you would when
backing up any vehicle.
●Be sure to back up slowly, depressing the
brake pedal to control vehicle speed.
●If you seem likely to hit nearby vehicles,
obstacles, people or mount the shoulder,
depress the brake pedal to stop the vehi-
cle, then disable the assist system by
selecting on the screen to cancel
the system.
IS_Navi_EE_53C71E.book 286 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

287
1. LEXUS PARKING ASSIST MONITOR
PERIPHERAL MONITORING SYSTEM
IS300h/250_Navi_EE
6
CAUTION
●The instructions given are only guidelines.
When and how much to turn the steering
wheel will vary according to traffic condi-
tions, road surface conditions, vehicle
condition, etc. when parking. It is neces-
sary to be fully aware of this before using
the parking assist system.
●When parking, be sure to check that the
parking space will accommodate your
vehicle before maneuvering into it.
●Do not use the parking assist monitor sys-
tem in the following cases:
• On icy or slick road surfaces, or in snow
•When using tyre chains
• When the trunk is not closed com-
pletely
• On roads that are not flat or straight,
such as curves or slopes
●In low temperatures, the screen may
darken or the image may become faint.
The image could distort when the vehicle
is moving, or you may become unable to
see the image on the screen. Be sure to
visually check all around the vehicle both
directly and using the mirrors before pro-
ceeding.
●If the tyre sizes are changed, the position
of the guide lines displayed on the screen
may change.
●The camera uses a special lens. The dis-
tances between objects and pedestrians
that appear in the image displayed on the
screen will differ from the actual dis-
tances. (→P. 3 0 6 )
IS_Navi_EE_53C71E.book 287 ページ ２０１４年５月２９日　木曜日　午前１１時２２分