Lexus IS250 2015 Navigation Manual

90
1. BASIC OPERATION
IS250/350_Navi_U
■MAP ONLY
■ DUAL MAP
zThe map on the left is the main map.
X Editing right map
1Select any point on the right side map.
2Select the desired item.
zWhen set to on, the indicator will illuminate.
The right side map can be edited.
No.FunctionPage
Select to change the orien-
tation of the map.88
Select to display POI icons.94
Select to show traffic infor-
mation. 100
Select to display eDestina-
tion icons.375
Select to change the map
scale.86

91
1. BASIC OPERATION
IS250/350_Navi_U
NAVIGATION SYSTEM
3
■COMPASS
Information about the destination, cur-
rent position and a compass is displayed
on the screen.
INFORMATION
● The destination mark is displayed in the
direction of the destination. When driv-
ing, refer to the longitude and latitude
coordinates, and the compass, to make
sure that the vehicle is headed in the
direction of the destination.
● When the vehicle travels out of the cov-
erage area, the guidance screen changes
to the whole compass mode screen.
SCREEN SCROLL
OPERATION
Use the scroll feature to move the de-
sired point to the center of the screen for
looking at a point on the map that is dif-
ferent from the current position.
No.Information/Function
Cursor mark
Distance from the current position to
the cursor mark
Select to set as a destination.
When selecting “Go to ” on the fol-
lowing map screen, the navigation
system performs a search for the
route. ( →P. 121)
If a destination has already been set,
“Go to ” and “Add to Route” will be
displayed.
“Go to ” : Select to delete the exist-
ing destination(s) and set a new one.
“Add to Route” : Select to add a desti-
nation.
Select to register as a memory point.
To change the icon, name, etc.: →P. 144
Select to return to the current posi-
tion.

92
1. BASIC OPERATION
IS250/350_Navi_U
zTo scroll over the map screen, place the
cursor mark in the desired position and
then press and hold the Remote Touch
knob. The map will cont inue scrolling in that
direction until the knob is released.
1Select one of the 8 directional arrows to
move the cursor to the desired point
and then select “OK”.
ADJUSTING LOCATION IN
SMALL INCREMENTS
The cursor location can be adjusted in
small increments when “Adjust Loca-
tion” is selected on the setting map
screen.
Also, when changing the location of
memory points on the editing screen
( → P. 146) and adjusting the current po-
sition mark manually on the “Calibration”
screen ( →P. 155), 8 directional arrows
may appear for this purpose.

93
1. BASIC OPERATION
IS250/350_Navi_U
NAVIGATION SYSTEM
3
3. MAP SCREEN INFORMATION
1Select “Options” on the map screen.
2Select “Map Information” .
3Select the desired items to be displayed.
zWhen set to on, the indicator will illuminate.
DISPLAYING MAP
INFORMATION
Information such as POI icons, route
trace, speed limit, etc. can be displayed
on the map screen.
No.FunctionPage
Select to display the select-
ed POI icons.
Select to select or change
POI icons.94
Select to display eDestina-
tion icons.375
Select to display route trace.96
Select to display traffic infor-
mation.100
Select to display speed limit
icon.

94
1. BASIC OPERATION
IS250/350_Navi_U
1Display the “Map Information” screen.
(→ P. 93)
2Select “Select POI” .
zWhen the POI icons to be displayed on the
map screen have already been set,
“Change POI” is displayed.
3Select the desired POI category and se-
lect “OK” .SELECTING THE POI ICONS
No.Information/FunctionPage
Displays up to 5 selected
POI icons on the map
screen.−
Select to cancel the select-
ed POI icons.−
Displays up to 6 POI icons
as favorite POI categories153
Select to display other POI
categories if the desired
POIs cannot be found on
the screen.
95
Select to search for the
nearest POIs.95

95
1. BASIC OPERATION
IS250/350_Navi_U
NAVIGATION SYSTEM
3
■SELECTING OTHER POI ICONS
TO BE DISPLAYED
1Select “Other POIs” .
2Select the desired POI categories and
select “OK”.
“List All Categories” : Select to display all
POI categories. To add more POI catego-
ries, select “More”.
■DISPLAYING THE LOCAL POI
LIST
1Select “Find Local POI”.
2Select the desired POI.
“Near...” : Select to search for POIs near the
current position or along the route.
3Check that the selected POI is dis-
played on the map screen. ( →P. 91)
POIs that are within 20 miles (32 km) of
the current position will be listed from
among the selected categories.

96
1. BASIC OPERATION
IS250/350_Navi_U
XWhen “Near...” is selected
1Select the desired item.
“Near Here” : Select to search for POIs
near the current position.
“A l o n g M y R o u t e ” : Select to search for
POIs along the route.
1Display the “Map Information” screen.
( → P. 93)
2Select “Route Trace”.
zThe “Route Trace” indicator illuminates and
the route trace starts.
3Check that the traveled line is displayed.
ROUTE TRACE
The traveled route can be stored and re-
traced on the map screen. This feature is
available when the map scale is 30 miles
(50 km) or less.

97
1. BASIC OPERATION
IS250/350_Navi_U
NAVIGATION SYSTEM
3
■STOP RECORDING THE ROUTE
TRACE
1Select “Route Trace” again.
2A confirmation screen will be displayed.
“Yes”: Select to keep the recorded
route trace.
“No” : Select to erase the recorded
route trace.
1Place the cursor over an icon.
2Select “Info”.
X POI information
X Memory point information
INFORMATION
●The traveled route can be stored up to
124 miles (200 km).
DISPLAYING INFORMATION
ABOUT THE ICON WHERE
THE CURSOR IS SET
When the cursor is placed over an icon
on the map screen, the name bar is dis-
played on the upper part of the screen. If
“Info” appears on the right side of the
name bar, detailed information can be
displayed.

98
1. BASIC OPERATION
IS250/350_Navi_U
XDestination information
X Traffic informationNo.Function
Select to register as a memory point.
To change the icon, name, etc.:
→P.
144
Select to set as a destination.
Select to call the registered number.
Select to delete destination or memo-
ry point.
Select to display the edit memory
point screen.
Select to display detailed information.
INFORMATION
● Even when traffic information is not cur-
rently being received, traffic information
and “Info” will be displayed for a while
after traffic information has been
received.

99
1. BASIC OPERATION
IS250/350_Navi_U
NAVIGATION SYSTEM
3
STANDARD MAP ICONS
IconName
Island
Park
Industry
Business facility
Airport
Military
University
Hospital
Stadium
Shopping mall
Golf