LEXUS LS430 2003 Factory Repair Manual

Page 2331 of 4500

Fig. 26: Installing Center Support Bearing Assy No. 1
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Using SST and a press, insert a new dust deflector until it almost touches the rubber of the center
support bearing assy No. 1.
SST 09608-00071, 09608-06041

Page 2332 of 4500

Fig. 27: Installing Dust Deflector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d. Using SST and a press, install a new dust deflector No. 2.
SST 09330-50010

Page 2333 of 4500

Fig. 28: Installing Dust Deflector No. 2
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e. Using a snap ring expander, install a new snap ring.

Page 2334 of 4500

Fig. 29: Installing Snap Ring
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
26.INSTALL PROPELLER INTERMEDIATE SHAFT ASSY
a. Install the dust boot.
b. Apply grease to the spline.
Grease:
Molybdenum disulfide lithium base, NLGI No. 2

Page 2335 of 4500

Fig. 30: Wrapping Vinyl Tape Around Spline
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Align the matchmarks and assemble the intermediate shaft and propeller shaft.
d. Cover the ad
justing nut with the dust boot.

Page 2336 of 4500

Fig. 31: Aligning Matchmarks
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e. Fully tighten the adjusting nut by hand.

Page 2337 of 4500

Fig. 32: Identifying Direction Of Intermediate Shaft And Propeller Shaft Companion Flange
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
27.INSTALL FLEXIBLE COUPLING
a. Install and torque the 3 bolts, washers and nuts.
Torque: 79 N.m (805 kgf.cm, 58 ft.lbf)

Page 2338 of 4500

Fig. 33: Installing Flexible Coupling
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
28.INSTALL PROPELLER W/CENTER BEARING SHAFT ASSY
a. Apply grease to the flexible coupling centering bushings.
Grease:
Molybdenum disulfide lithium base, NLGI No. 2

Page 2339 of 4500

Fig. 34: Applying Grease To Flexible Coupling Centering Bushing
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Install the propeller shaft from the vehicle's rear and connect the transmission and differential.
c. Temporaril
y install the 2 center support bearing set bolts with the adjusting washers.

Page 2340 of 4500

Fig. 35: Installing Center Support Bearing Bolts And Adjusting Washers
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
Use the adjusting washers which were removed.
d. Align the matchmarks and connect the propeller shaft to the transmission/differential.
e. Install and torque the 6 bolts, washers and nuts.
Torque: 79 N.m (805 kgf.cm, 58 ft.lbf)

Page:   < prev 1-10 ... 2291-2300 2301-2310 2311-2320 2321-2330 2331-2340 2341-2350 2351-2360 2361-2370 2371-2380 ... 4500 next >