lock MAZDA MODEL CX-3 2015 (in English) Workshop Manual

3–45
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will fl ash three
times.
NOTE
  To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
  The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.
The hazard warning lights will fl ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will fl ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.


 
 Pressing the electric liftgate opener
while the key is being carried.
The hazard warning lights will fl ash twice.
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the glove compartment.
Mazda recommends that you affi x it to the
lower rear corner of a front door window.
$9@&;&&%@&EJUJPOJOEC







3–47
Before Driving
Driving Tips
WARNING
Never stop the engine when going
down a hill:
Stopping the engine when going
down a hill is dangerous. This causes
the loss of power steering and power
brake control, and may cause damage
to the drivetrain. Any loss of steering
or braking control could cause an
accident.
Hazardous Driving
WARNING
Be extremely careful if it is necessary
to downshift on slippery surfaces:
Downshifting into lower gear while
driving on slippery surfaces is
dangerous. The sudden change in tyre
speed could cause the tyres to skid. This
could lead to loss of vehicle control and
an accident.
When driving on ice or in water, snow,
mud, sand, or similar hazards:
 


 Be cautious and allow extra distance for
braking.
 


 Avoid sudden braking and sudden
manoeuvring.
 


 Do not pump the brakes. Continue to
press down on the brake pedal.
  Refer to Antilock Brake System (ABS)
on page 4-81 .
 


 If you get stuck, select a lower gear and
accelerate slowly. Do not spin the front
wheels.
 


 For more traction in starting on slippery
surfaces such as ice or packed snow,
use sand, rock salt, chains, carpeting, or
other nonslip material under the front
wheels.
NOTE
Use snow chains only on the front
wheels.
$9@&;&&%@&EJUJPOJOEC







3–50
Before Driving
Driving Tips
NOTE
  Do not use the parking brake in
freezing weather as it may freeze.
Instead, shift to P with an automatic
transaxle and to 1 or R with a manual
transaxle. Block the rear wheels.
  Remove snow before driving. Snow
left on the windscreen is dangerous
as it could obstruct vision.
  Do not apply excessive force to a
window scraper when removing ice
or frozen snow on the mirror glass
and windscreen.
  Never use warm or hot water for
removing snow or ice from windows
and mirrors as it could result in the
glass cracking.
  Drive slowly. Braking performance
can be adversely affected if
snow or ice adheres to the brake
components. If this situation occurs,
drive the vehicle slowly, releasing
the accelerator pedal and lightly
applying the brakes several times
until the brake performance returns
to normal.
Snow Tyres
WARNING
Use only the same size and type tyres
(snow, radial, or non-radial) on all four
wheels:
Using tyres different in size or type is
dangerous. Your vehicle's handling
could be greatly affected and result in
an accident.
CAUTION
Check local regulations before using
studded tyres.
Use snow tyres on all four wheels
Do not exceed the maximum permissible
speed for your snow tyres or legal speed
limits.
Europe
When snow tyres are used, select the
specifi ed size and pressure (page 9-9 ).
Tyre Chains
Check local regulations before using tyre
chains.
CAUTION
  Chains may affect handling. 
 Do not go faster than 50 km/h (30
mph) or the chain manufacturer's
recommended limit, whichever is
lower.
  Drive carefully and avoid bumps,
holes, and sharp turns.
  Avoid locked-wheel braking. 
 Do not use chains on a temporary
spare tyre; it may result in damage to
the vehicle and to the tyre. In some
models, the vehicle is not equipped
with a factory installed temporary
spare tyre.
  Do not use chains on roads that are
free of snow or ice. The tyres and
chains could be damaged.
  Chains may scratch or chip
aluminium wheels.
$9@&;&&%@&EJUJPOJOEC







3–61
Before Driving
Towing
 


 When ascending a hill, shift into a lower gear to reduce the possibility of overloading or
overheating the engine, or both.
 


 When descending a hill, shift into a lower gear and use engine compression as a braking
effect. Pay constant attention to speed and use the brakes only as needed. Holding the
brake pedal down for a prolonged period may cause the brakes to overheat and lose
power.
Parking
Avoid parking on an incline with a trailer. If this must be done, follow these instructions.
Parking on an Incline
1. Set the parking brake and the brakes.
2. Have someone block the wheels of the vehicle and trailer while you apply the brakes.
3. After the wheels are blocked, release the parking brake and the brakes slowly, allowing
the blocks to bear the load.
4. Set the parking brake fi rmly.
5. If the vehicle has an automatic transaxle, put the selector lever in P. If it has a manual
transaxle, place the gear shift in 1 or R.
Starting on an Incline
1. Start the engine (page 4-5 ).
2. Release the parking brake and slowly pull away a short distance from the wheel blocks.
3. Stop on the nearest level ground, set the parking brake, and pick up the wheel blocks.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–1
4When Driving
Information concerning safe driving and stopping.



Start/Stop Engine ................................ 4-4
Ignition Switch ............................... 4-4
Starting the Engine ......................... 4-5
Turning the Engine Off ................ 4-11
i-stop
* ........................................... 4-13
Instrument Cluster and Display ...... 4-23
Meters and Gauges ....................... 4-23
Active Driving Display
* ............... 4-34
Warning/Indicator Lights ............. 4-36
Transaxle ............................................ 4-44
Manual Transaxle Operation ........ 4-44
Automatic Transaxle Controls ...... 4-47
Switches and Controls ...................... 4-58
Lighting Control ........................... 4-58
Front Fog Lights
* ......................... 4-65
Rear Fog Light* ............................ 4-66
Turn and Lane-Change Signals ...... 4-67
Windscreen Wipers and Washer ...... 4-68
Rear Window Wiper and
Washer
*......................................... 4-72
Headlight Washer* ........................ 4-73
Rear Window Defogger ............... 4-73
Horn ............................................. 4-74
Hazard Warning Flasher ............... 4-75
Brake .................................................. 4-76
Brake System ............................... 4-76
Emergency Stop Signal System ...... 4-79
Hill Launch Assist (HLA)* ........... 4-79 ABS/TCS/DSC ................................... 4-81
Antilock Brake System (ABS) ...... 4-81
Traction Control System (TCS) ...... 4-82
Dynamic Stability Control
(DSC) ........................................... 4-84
i-ELOOP ............................................ 4-85
i-ELOOP
* ..................................... 4-85
Fuel Economy Monitor ..................... 4-88
Fuel Economy Monitor
* ............... 4-88
Drive Selection ................................... 4-93
Drive Selection
* ........................... 4-93
4WD .................................................... 4-95
4-Wheel Drive (4WD)
Operation ...................................... 4-95
Power Steering................................... 4-97
Power Steering ............................. 4-97
$9@&;&&%@&EJUJPOJOEC







4–4
When Driving
Start/Stop Engine
Ignition Switch
Push Button Start Positions
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Push button startIndicator light
NOTE
  The engine starts by pressing the
push button start while depressing
the clutch pedal (manual transaxle)
or the brake pedal (automatic
transaxle). To switch the ignition
position, press the push button start
without depressing the pedal.
  Do not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transaxle, the
selector lever is in the P position, and
the ignition is in ACC), the ignition
switches off automatically after about
25 minutes. Off
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat, always
switch the ignition off, set the parking
brake, and make sure the selector lever
is in P (automatic transaxle) or in 1st
gear or R (manual transaxle):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transaxle) or
to 1st gear or R (manual transaxle)
is dangerous. Unexpected vehicle
movement could occur which could
result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is fl ashing and the beep sound
is heard, this indicates that the steering
wheel is not unlocked. To unlock the
steering wheel, press the push button
start while moving the steering wheel
left and right.
$9@&;&&%@&EJUJPOJOEC







4–5
When Driving
Start/Stop Engine
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start has
been pressed to ACC, and the doors will
not lock/unlock even if they have been
locked manually.
O N
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-36 ).
NOTE
(SKYACTIV-G 2.0)
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
NOTE
  The key must be carried because the
key carries an immobilizer chip that
must communicate with the engine
controls at short range.
  The engine can be started when the
push button start is pressed from off,
ACC, or ON.
  The push button start system
functions (function which can start
the engine by only carrying the
key) can be deactivated to prevent
any possible adverse effect on a
user wearing a pacemaker or other
medical device. If the system is
deactivated, you will be unable
to start the engine by carrying the
key. Consult an expert repairer, we
recommend an Authorised Mazda
Repairer for details. If the push
button start system functions have
been deactivated, you can start the
engine by following the procedure
indicated when the key battery goes
dead.
 Refer to Engine Start Function When
Key Battery is Dead on page 4-9 .
$9@&;&&%@&EJUJPOJOEC







4–10
When Driving
Start/Stop Engine
If the engine cannot be started due to a
dead key battery, the engine can be started
using the following procedure:
1. Continue to depress the brake pedal
fi rmly until the engine has completely
started.
2. (Manual transaxle)
Continue to depress the clutch pedal
fi rmly until the engine has completely
started.
3. Verify that the push button start
indication light (green) fl ashes.
NOTE
The push button start indicator light
(green) will fl ash even if the push button
start is pressed before depressing the
brake pedal (automatic transaxle) or
the clutch pedal (manual transaxle). If
the clutch pedal is depressed (manual
transaxle) or the brake pedal is
depressed (automatic transaxle) under
this condition, the engine can be started
by resuming the procedure following
this.
4. Touch the push button start using the
backside of the key (as shown) while
the push button start indicator light
(green) fl ashes.
Push button start
TransmitterIndicator light
NOTE
When touching the push button start
using the backside of the key as shown
in the illustration, touch the push button
start with the lock switch side of the key
facing up.
5. Verify that the push button start
indicator light (green) turns on.
6. Press the push button start to start the
engine.
NOTE
  The engine cannot be started unless
the clutch pedal is fully depressed
(manual transaxle) or the brake
pedal is fully depressed (automatic
transaxle).
  If there is a malfunction with the
push button start function, the push
button start indicator light (amber)
fl ashes. In this case, the engine may
start, however, have the vehicle
checked at an expert repairer, we
recommend an Authorised Mazda
Repairer as soon as possible.
  If the push button start indicator light
(green) does not illuminate, perform
the operation from the beginning
again. If it does not illuminate,
have the vehicle checked at an
expert repairer, we recommend an
Authorised Mazda Repairer.
$9@&;&&%@&EJUJPOJOEC







4–47
When Driving
Transaxle
Automatic Transaxle Controls
Lock-release button
Indicates the selector lever can be shifted freely into any position.
Indicates that you must hold in the lock-release button to shift.
Indicates that you must depress the brake pedal and hold in the lock-release
button to shift (The ignition must be switched ON).
Various Lockouts:
NOTE
The Sport AT has an option that is not included in the traditional automatic transaxle that
gives the driver the option of selecting each gear instead of leaving it to the transaxle to
shift gears. Even if you intend to use the automatic transaxle functions as a traditional
automatic, you should also be aware that you can inadvertently shift into manual shift
mode and an inappropriate gear may be retained as the vehicle speed increases. If you
notice the engine speed going higher or hear the engine racing, confi rm you have not
accidentally slipped into manual shift mode (page 4-50 ).
$9@&;&&%@&EJUJPOJOEC







4–48
When Driving
Transaxle
Shift Position Indication
The selector position is indicated when the
ignition is switched ON.
NOTE
If one of the following actions is
performed, the selector position is
displayed for 5 minutes even if the
ignition switch is in a position other than
ON.
 
 The ignition is switched OFF. 
 The driver's door is opened.
Gear position indication
In manual shift mode, the “M” of the shift
position indication illuminates and the
numeral for the selected gear is displayed.
Warning Light
The warning light turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-37 .
Transaxle Ranges
 












 The shift position indicator light in the
instrument cluster illuminates. Refer to
Warning/Indicator Lights on page 4-36 .
 


 The selector lever must be in P or N to
operate the starter.
P (Park)
P locks the transaxle and prevents the front
wheels from rotating.
WARNING
Always set the selector lever to P and
set the parking brake:
Only setting the selector lever to the
P position without using the parking
brake to hold the vehicle is dangerous.
If P fails to hold, the vehicle could
move and cause an accident.
CAUTION
  Shifting into P, N or R while the
vehicle is moving can damage your
transaxle.
  Shifting into a driving gear or reverse
when the engine is running faster
than idle can damage the transaxle.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete
stop before shifting to or from R, except
under rare circumstances as explained in
Rocking the Vehicle (page 3-49 ).
N (Neutral)
In N, the wheels and transaxle are not
locked. The vehicle will roll freely even
on the slightest incline unless the parking
brake or brakes are on.
$9@&;&&%@&EJUJPOJOEC