ignition MAZDA MODEL CX-30 2019 Owners Manual (in English)

Route the jumper leads away from parts that will be moving:
Connecting a jumper lead near or to moving parts (cooling fans, belts) is dangerous.
The lead could get caught when the engine starts and cause serious injury.
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and
other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in
series or a 24 V motor generator set).
1. Move the booster vehicle so that its battery is as close as possible to your
vehicle's battery.
2. Make sure that the power such as for the headlights and air conditioner is turned
off.
3. Remove the battery cover.
4. Turn off the booster vehicle's engine and connect the jumper leads in the
following order.
Make sure that the jumper leads are securely connected so that they do not
disconnect due to engine vibrations.
1st lead
Positive (+) terminal on the discharged battery
Positive (+) terminal on booster vehicle's battery
2nd lead
Negative (-) terminal on booster vehicle's battery
If Trouble Arises
Battery Runs Out
7-40

Overheating
▼Overheating
If the engine coolant temperature
gauge indicates overheating and the
high engine coolant temperature
warning indication is displayed, the
vehicle loses power or you hear a loud
knocking or pinging noise, the engine
is probably too hot.
WARNING
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running
indefinitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the bonnet ONLY after steam is
no longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the engine coolant temperature
gauge indicates overheating and the
high engine coolant temperature
warning indication is displayed:

1. Drive safely to the side of the road
and park off the right-of-way.
2. Put a vehicle with an automatic
transmission in park (P), a manual
transmission in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine
compartment.

If steam is coming from the engine
compartment:
Do not go near the front of the
vehicle. Stop the engine.
Wait until the steam dissipates,
then open the bonnet and start the
engine.

If neither coolant nor steam is
escaping:
Open the bonnet and idle the
engine until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the
engine temperature will increase.
Stop the engine and call an expert
repairer (we recommend an
Authorised Mazda Repairer).
6. Make sure the cooling fan is
operating, then turn off the engine
after the temperature has
decreased.
7. When cool, check the coolant level.
If Trouble Arises
Overheating
7-44

¾If the parking brake cannot be
released when towing the vehicle,
transport the vehicle with all front
and rear wheels raised off the ground
as shown in the figure. If the vehicle
is towed without raising the wheels
off the ground, the brake system
could be damaged.
1. Wheel dollies
If towing service is not available in an
emergency, the vehicle may be towed
with all four wheels on the ground
using the towing hook at the front of
the vehicle.
Only tow the vehicle on paved surfaces
for short distances at low speeds.
CAUTION
Follow these instructions when towing
the vehicle with all wheels on the
ground.
1. Shift to neutral (Manual
transmission), or the N position
(Automatic transmission).
2. Switch the ignition to ON.
3. Release the parking brake.
Refer to Electric Parking Brake (EPB)
on page 4-70.
Remember that power assist for the
brakes and steering will not be
available when the engine is not
running.
Towing Hooks
▼Towing Hooks
CAUTION
¾The towing eyelet should be used in
an emergency (to get the vehicle out
of a ditch or a snow bank, for
example).
¾When using the towing eyelets,
always pull the lead or chain in a
straight direction with respect to the
eyelet. Never apply a sideways force.
NOTE
When towing with chain or lead, wrap
the chain or lead with a soft cloth near
the bumper to prevent damage to the
bumper.
1. Remove the towing eyelet, wheel
brace, and the jack lever or
equivalent from the luggage
compartment (page 7-24).
2. Wrap a flathead screwdriver or jack
lever or a similar tool with a soft
cloth to prevent damage to a
painted bumper, and open the cap
located on the front or rear
bumper.
Front
If Trouble Arises
Emergency Towing
7-47

If a Warning Light Turns
On or Flashes
▼If a Warning Light Turns On or
Flashes
If any warning light turns on/flashes,
take appropriate action for each light.
There is no problem if the light turns
off, however if the light does not turn
off or turns
on/flashes again, consult
an expert repairer (we recommend an
Authorised Mazda Repairer).
The details for some warnings can be
viewed on the centre display or
multi-information display in the
instrument cluster.
Centre display
1. Select “Information” on the home
screen.
2. Select “Vehicle Status Monitor”.
3. Select the applicable warning to
view the warning details.
NOTE
You can also display the currently
occurring warning by sliding the
commander knob to the left while on
the home screen of the centre display.
Multi-information display
1. Press the INFO switch on the
steering switch to display the
warning indication screen.
Refer to Multi-information Display
on page 4-23.
▼Brake System Warning Indication/
Warning Light (Red)
This warning has the following
functions:
Warning light inspection
For an operation check, make sure that
the light turns on when the ignition is
switched on, and turns off a few
seconds later or when the engine is
started.
When the light turns on
If the brake system warning light
remains illuminated the brake fluid
may be low or there could be a
problem with the brake system. Park
the vehicle in a safe place immediately
and contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
Refer to Inspecting Brake/Clutch Fluid
Level on page 6-30.
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
expert repairer (we recommend an
Authorised Mazda Repairer) to have
the brakes inspected as soon as
possible:
Driving with the brake system warning
light illuminated is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this light
remains illuminated, after checking
that the parking brake is fully released,
have the brakes inspected
immediately.
CAUTION
¾In addition, the
effectiveness of the
braking may diminish so you may
need to depress the brake pedal
more strongly than normal to stop
the vehicle.
¾(With M Hybrid)
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-49

xRepeatedly jerking the steering
wheel left and right while the vehicle
is stopped or moving extremely
slowly will cause the power steering
system to go into protective mode
which will make the steering feel
heavy, but this does not indicate a
problem. If this occurs, park the
vehicle safely and wait several
minutes for the system to return to
normal.
▼ABS Warning Indication/Warning
Light
If the ABS warning light stays on while
you're driving , the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
NOTE
xWhen the engine is jump-started to
charge the battery, uneven rpm
occurs and the ABS warning light
may illuminate. If this occurs, it is the
result of the weak battery and does
not indicate an ABS malfunction.
Recharge the battery.
xThe brake assist system does not
operate while the ABS warning light
is illuminated.
▼Master Warning Indication
The indication displays if the system
has a malfunction.
Check the reason for the indication
displaying on the centre display or
multi-information display.
Refer to If a Warning Light Turns On or
Flashes on page 7-49.
▼Brake Control System Warning
Indication/Warning Light (Amber)
The warning light illuminates when the
system has a malfunction. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
▼Electric Parking Brake (EPB)
Indication/Indicator Light
This warning has the following
functions:
Parking brake warning/Indicator light
inspection
The light illuminates when the parking
brake is applied with the ignition
switched to START or ON. It turns
off
when the parking brake is released.
When the light is
flashing
The light flashes if the Electric Parking
Brake (EPB) has a malfunction. If the
light remains flashing even if the
Electric Parking Brake (EPB) switch is
operated, consult an expert repairer
(we recommend an Authorised Mazda
Repairer) as soon as possible.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-52

▼Brake Override Warning Indication
This message is displayed when the
accelerator pedal and brake pedal are
depressed at the same time while
driving.
Release the accelerator pedal and
depress the brake pedal.
▼Check Engine Indication/Light
If this light illuminates while driving ,
the vehicle may have a problem. It is
important to note the driving
conditions when the light illuminated
and consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
The check engine light may illuminate
in the following cases:
xThe engine's electrical system has a
problem.
xThe emission control system has a
problem.
x(Except SKYACTIV-D 1.8)
xThe fuel tank level being very low
or approaching empty.
xThe
fuel-filler cap is missing or not
tightened securely.
If the check engine light remains on, or
it flashes continuously , do not drive at
high speeds and consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
WARNING
If the check engine light turns on, do
not disconnect the battery leads.
If the battery leads are disconnected
and then reconnected, the engine
could be damaged and catch on
fire.
▼i-stop Warning Indication/
Warning Light (Amber)*
When the light is turned on
xA problem in the system may be
indicated under the following
conditions. Have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe light does not turn on when
the ignition is switched ON.
x(Except European model)
If the i-stop warning light (amber)
remains on while the engine is
running , the battery performance
may have decreased. Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
When the light is flashing
The light continues to flash if the
system has a malfunction. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-53

CAUTION
If the vehicle is continually driven as
usual with the diesel particulate filter
warning light turned on, PM increases
and the warning light may start
flashing. If the diesel particulate filter
warning light starts flashing, have the
vehicle inspected immediately at an
expert repairer (we recommend an
Authorised Mazda Repairer). If the
vehicle is not inspected and continues
to be driven, the engine may
malfunction.
NOTE
xWhen the diesel particulate filter
warning light
flashes, the engine
output is restricted to protect the
diesel particulate
filter.
xThe engine sound and exhaust gas
smell may change when PM is being
removed while driving.
▼Automatic Transmission Warning
Indication/Warning Light*
The indication/light illuminates when
the transmission has a problem.
CAUTION
If the automatic transmission warning
indication/light illuminates, the
transmission has an electrical problem.
Continuing to drive your Mazda in this
condition could cause damage to your
transmission. Consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
▼TCS/DSC Indication/Indicator
Light (Turns on)
If the light stays on, the TCS, DSC or
the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an
expert repairer (we recommend an
Authorised Mazda Repairer).
▼Air Bag/Seat Belt Pretensioner
System Warning Indication/
Warning Light
A system malfunction is indicated if the
warning light constantly
flashes,
constantly illuminates or does not
illuminate at all when the ignition is
switched ON. If any of these occur,
consult an expert repairer (we
recommend an Authorised Mazda
Repairer) as soon as possible. The
system may not operate in an accident.
WARNING
Never tamper with the air bag/
pretensioner systems and always have
an expert repairer (we recommend an
Authorised Mazda Repairer) perform
all servicing and repairs:
Self-servicing or tampering with the
systems is dangerous. An air bag/
pretensioner could accidentally
activate or become disabled causing
serious injury or death.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-55

▼KEY Warning Indication/Warning
Light (Red)
“Keyless Entry System Malfunc. Have
the Vehicle Inspected” is displayed
This message is displayed if the
advanced keyless entry & push button
start system has a problem.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
CAUTION
If the message is indicated, or the push
button start indicator light (amber)
flashes, the engine may not start. If the
engine cannot be started, try starting it
using the emergency operation for
starting the engine, and have the
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer) as soon as possible.
Refer to Emergency Operation for
Starting the Engine on page 4-9.
“Key Not Detected” is displayed
xIf the presence of the key cannot be
detected (dead battery, battery
malfunction, no key), it is displayed
when the driver attempts to start the
engine (push button start operation,
brake pedal depression).
xDisplayed when it is determined that
a key that was in the vehicle has
been removed from the vehicle. (Key
taken out warning. Other than
IG-OFF).
▼Security Indicator Light
If the security indicator light flashes
continuously while you are driving, do
not shut
off the engine. Go to an
expert repairer (we recommend an
Authorised Mazda Repairer) and have
it checked. If the engine is shut off
while the indicator light is
flashing , you
will not be able to restart it.
Make sure the key is within the
operational range for signal
transmission. Switch the ignition off,
and then restart the engine. If the
engine does not start after 3 or more
tries, contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
NOTE
Because the electronic codes are reset
when the immobilizer system is
repaired, the keys are needed. Make
sure to bring all the keys to an
Authorised Mazda Repairer so that
they can be programmed.
▼AWD Warning Indication/
Warning Light*
“AWD Malfunction. Front Wheel
Drive Only. Have the Vehicle
Inspected” is displayed/When the
light is turned on
The indication is displayed/the light
turns on under the following
conditions. The system may have a
malfunction. Have the vehicle checked
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-56*Some models.

NOTE
The light illumination timing may vary
because fuel inside the fuel tank moves
around according to the driving
conditions and the vehicle posture.
Action to be taken
Add fuel. If the light is flashing, refuel
as soon as possible.
▼Engine Oil Level Warning
Indication/Warning Light
This warning light indicates that the
engine oil level is around the MIN
mark (page 6-27).
CAUTION
Do not continue to drive the vehicle
with the engine oil level warning
indication/warning light displayed/
turned on. If the vehicle continues to
be driven with an insufficient amount
of engine oil, it could cause damage to
the engine.
Action to be taken
Add 1 L (0.3 US gal, 0.2 Imp gal) of
engine oil (page 6-24).
▼Seat Belt Warning Indication/
Warning Light (Front seat)
The seat belt warning light turns on if
the driver or front passenger's seat is
occupied and the seat belt is not
fastened with the ignition switched
ON.
If the driver or front passenger's seat
belt is unfastened (only when the front
passenger's seat is occupied) and the
vehicle is driven at a speed faster than
about 20 km/h (12 mph), the warning
light flashes. After a short time, the
warning light stops flashing, but
remains illuminated. If a seat belt
remains unfastened, the warning light
flashes again for a given period of
time.
NOTE
xIf the driver or front passenger's seat
belt is unfastened after the warning
light turns on, and the vehicle speed
exceeds 20 km/h (12 mph), the
warning light flashes again.
xPlacing heavy items on the front
passenger's seat may cause the front
passenger's seat belt warning
function to operate depending on
the weight of the item.
xTo allow the front passenger seat
weight sensor to function properly,
do not place and sit on an additional
seat cushion on the front passenger's
seat. The sensor may not function
properly because the additional seat
cushion could cause sensor
interference.
xIf a small child is seated on the front
passenger's seat, the warning light
may not operate.
Action to be taken
Fasten the seat belts.
▼Seat Belt Warning Light (Rear seat)
(Red)
If the rear seat belts are not fastened
while the ignition is switched ON , the
driver and the passenger are alerted by
the warning light.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-59

“Low Key Fob Battery. Replace
Battery” is displayed/When the light
is flashing
When the key battery is low, the
indication is displayed when the
ignition is switched OFF.
Action to be taken
Replace the key battery.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-62