ignition MAZDA MODEL CX-30 2019 Owners Manual (in English)

Cruise Control*
▼Cruise Control
With cruise control, you can set and
automatically maintain any speed of
more than about 30 km/h (19 mph).
WARNING
Do not use the cruise control under
the following conditions:
Using the cruise control under the
following conditions is dangerous and
could result in loss of vehicle control.
¾Hilly terrain
¾Steep inclines
¾Heavy or unsteady traffic
¾Slippery or winding roads
¾Similar restrictions that require
inconsistent speed
▼Cruise Control Switch
1. CANCEL switch
2. RES switch
3. Cruise switch
NOTE
If your Mazda has the following
steering switch, your Mazda is
equipped with the Mazda Radar
Cruise Control (MRCC) system, the
Mazda Radar Cruise Control with Stop
& Go function (MRCC with Stop & Go
function) system.
Refer to Mazda Radar Cruise Control
(MRCC) on page 4-130.
Refer to Mazda Radar Cruise Control
with Stop & Go function (MRCC with
Stop & Go function) on page 4-139.
If the Mazda Radar Cruise Control
(MRCC) or Mazda Radar Cruise
Control with Stop & Go function
(MRCC with Stop & Go function) is set
to inoperable using the personalisation
feature, the system switches to the
cruise control function. In this case, the
MRCC functions as the cruise switch.
In addition, this personalisation feature
setting is initialized by switching the
ignition OFF, and it turns back on
when the ignition is switched ON the
next time.
▼Cruise Standby Indication
(White)/Cruise Set Indication
(Green)
Cruise standby Indication (White)
The indication turns on (white) when
the cruise control system is activated.
When Driving
Cruise Control
4-228*Some models.

Cruise Set Indication (Green)
The indication turns on (green) when a
cruising speed has been set.
▼Activation/Deactivation
WARNING
Always turn off the cruise control
system when it is not in use:
Leaving the cruise control system in an
activation-ready state while the cruise
control is not in use is dangerous as the
cruise control could unexpectedly
activate if the activation button is
accidentally pressed, and result in loss
of vehicle control and an accident.
NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the
ignition is switched OFF with the cruise
control system operable, the system
will be operable when the ignition is
switched ON the next time.
Activation
To activate the system, press the cruise
switch. The cruise standby indication
(white) turns on.
Deactivation
To deactivate the system, press the
cruise switch again.
The cruise standby indication (white)
turns
off.
▼To Set Speed
1. Activate the cruise control system
by pressing the cruise switch. The
cruise standby indication (white)
turns on.
2. Accelerate to the desired speed,
which must be more than 25 km/h
(16 mph).
3. Adjust the system to the desired
vehicle speed using the accelerator
pedal. Press the RES switch up (SET
+) or down (SET-) to start cruise
control. The cruise control
indication (green) in the instrument
cluster turns on at the same time.
Quickly release the switch when the
cruise control indication (green)
turns on.
NOTE
xIf the RES switch is operated up (SET
+) or down (SET-) while the vehicle
speed is between 25 km/h (16 mph)
and 30 km/h (19 mph), the set
speed is set to 30 km/h (19 mph).
xThe cruise control speed setting
cannot be performed under the
following conditions:
xAny of the doors is opened.xThe driver's seat belt is unfastened.xThe brake pedal is depressed.xThe parking brake is applied.x(Automatic transmission)
The selector lever is in the P or N
position.
x(Manual transmission)
The shift lever is in the neutral
position.
xOn a steep grade, the vehicle may
momentarily slow down while
ascending or speed up while
descending.
xThe cruise control will cancel if the
vehicle speed decreases below 20
km/h (12 mph) when the cruise
control is activated, such as when
climbing a steep grade.
When Driving
Cruise Control
4-229

xIf “No camera signal.” is indicated in
the display, there could be a
problem with the camera. Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
x(Predicted vehicle path assist lines
display type)
If force is applied to the steering
wheel, the guide lines may not
display. Loosen your grip on the
steering wheel to allow the guide
lines to display.
▼Rear View Parking Camera
Location
1. Rear view parking camera
▼Switching to the Rear View
Monitor Display
Shift the shift lever (manual
transmission) or the selector lever
(automatic transmission) to reverse (R)
position with the ignition switched ON
to switch the display to the rear view
monitor display.
NOTE
When the shift lever (manual
transmission) or the selector lever
(automatic transmission) is shifted
from reverse (R) position to another
shift lever (manual transmission) or the
selector lever (automatic transmission)
position, the screen returns to the
previous display.
When Driving
Rear View Monitor
4-239

DisplayDistance between vehicle and obstruc-
tion
Without 360° view monitor
With 360° view
monitorFront ultrasonic
sensor
*/Front cor-
ner ultrasonic sen-
sor
*
Rear ultrasonic sen-
sor/Rear corner ul-
trasonic sensor/
Rear side ultrasonic
sensor
*
Without front ul-
trasonic sensor
and front corner
ultrasonic sensorWith front ultra-
sonic sensor and
front corner ultra-
sonic sensor
YellowFront ultrasonic sen-
sor:
Approx. 60.0Š45.0
cm (23.6Š17.7 in)
Front corner ultra-
sonic sensor:
Approx. 55.0Š38.0
cm (21.6Š14.9 in)Rear ultrasonic sen-
sor:
Approx. 60.0Š45.0
cm (23.6Š17.7 in)
Rear corner ultra-
sonic sensor/Rear
side ultrasonic sen-
sor:
Approx. 55.0Š38.0
cm (21.6Š14.9 in)
AmberFront ultrasonic sen-
sor:
Approx. 45.0Š35.0
cm (17.7Š13.7 in)
Front corner ultra-
sonic sensor:
Approx. 38.0Š25
cm (14.9Š9.8 in)Rear ultrasonic sen-
sor:
Approx. 45.0Š35.0
cm (17.7Š13.7 in)
Rear corner ultra-
sonic sensor/Rear
side ultrasonic sen-
sor:
Approx. 38.0Š25
cm (14.9Š9.8 in)
RedFront ultrasonic sen-
sor:
Within approx. 35.0
cm (13.7 in)
Front corner ultra-
sonic sensor:
Within approx. 25
cm (9.8 in)Rear ultrasonic sen-
sor:
Within approx. 35.0
cm (13.7 in)
Rear corner ultra-
sonic sensor/Rear
side ultrasonic sen-
sor:
Within approx. 25
cm (9.8 in)
▼Park Assist Sensor System
Operation
When the parking sensor switch is
pressed with the ignition switched ON,
the indicator light turns on.
When the ignition is switched ON with
the parking sensor activated, the
indicator light turns on.
When Driving
Parking Sensor System
*Some models.4-255

Press the switch again to stop the
operation.
1. Indicator light
NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the
ignition is switched OFF while the
parking sensor is activated, the system
will be activated when the ignition is
switched ON the next time.
Operation conditions
The parking sensor system can be used
when all of the following conditions
are met:
xThe ignition is switched ON.xThe parking sensor switch is turned
on.
NOTE
x(Automatic vehicle)
The detection indicator and buzzer
of the front sensors/front corner
sensors do not operate when the
selector lever is in the P position.
xThe detection indicator and buzzer
sound do not activate when the
parking brake is applied.
▼Obstruction Detection Indication
The position of a sensor which has
detected an obstruction is indicated.
The gauge illuminates in different areas
depending on the distance to an
obstruction detected by the sensor.
As the vehicle approaches closer to an
obstruction, the zone in the gauge
closer to the vehicle illuminates.
Without 360°view monitor
1. Front ultrasonic sensor gauge*
2. Right front corner ultrasonic sensor
gauge*
3. Right rear corner ultrasonic sensor
gauge/Right rear side ultrasonic
sensor gauge
*
4. Rear ultrasonic sensor gauge
5. Left rear corner ultrasonic sensor
gauge/Left rear side ultrasonic
sensor gauge
*
6. Left front corner ultrasonic sensor
gauge*
With 360°view monitor
1. Front ultrasonic sensor gauge
2. Right front corner ultrasonic sensor
gauge
When Driving
Parking Sensor System
4-256*Some models.

Operating Tips
▼Operating Tips
xOperate the air-conditioning system
with the engine running.
xTo prevent the battery from being
discharged, do not leave the fan
control dial/switch on for a long
period of time with the ignition
switched ON when the engine is not
running.
x(With i-stop)
The
airflow amount may decrease
slightly while the i-stop function is
operating.
xClear all obstructions such as leaves,
snow and ice from the bonnet and
the air inlet in the cowl grille to
improve the system efficiency.
xUse the air-conditioning system to
defog the windows and dehumidify
the air.
xThe recirculate mode should be used
when driving through tunnels or
while in a
traffic jam, or when you
would like to shut off outside air for
quick cooling of the interior.
xUse the outside air position for
ventilation or windscreen defrosting.
xIf the vehicle has been parked in
direct sunlight during hot weather,
open the windows to let warm air
escape, then run the air-conditioning
system.
xRun the air conditioner about 10
minutes at least once a month to
keep internal parts lubricated.
xHave the air conditioner checked
before the weather gets hot. Lack of
refrigerant may make the air
conditioner less efficient.
The refrigerant specifications are
indicated on a label attached to the
inside of the engine compartment. If
the wrong type of refrigerant is used,
it could result in a serious
malfunction of the air conditioner.
Consult a professional, government
certified repairer for the inspection
or repair because a special device is
required for the air conditioner
maintenance.
For details, consult an expert repairer
(we recommend an Authorised
Mazda Repairer).
1. Label
Interior Features
Air-Conditioning System
5-2

Sunvisors
▼Sunvisors
When you need a sunvisor, lower it for
use in front or swing it to the side.
▼Vanity Mirrors
To use the vanity mirror, lower the
sunvisor.
If your vehicle is equipped with a
vanity mirror light, it will illuminate
when you open the cover.
The vanity mirror will only illuminate in
the tilt range shown in the
figure.

1. Vanity mirror light
2. On
3. Off

NOTE
If a vanity mirror light is left on with the
ignition switched OFF, the light is
turned off automatically to prevent the
battery from being discharged.

The vanity mirror light can be turned
on again by doing any of the following
operations:
xOpening/closing any door.xUnlocking any door.xSwitching the ignition to ACC or ON.xSwitching an overhead light/front
map light on.
Interior Features
Interior Equipment
5-32

xThe driver's door is unlocked with
the ignition is switched OFF.
xThe ignition is switched OFF with all
doors closed.
NOTE
xThe illumination time differs
depending on the operation.
xThe vehicle is equipped with a
battery saver. If an interior light is left
on with the ignition switched OFF,
the light is turned off automatically
after about 15 minutes to prevent
battery depletion.
xThe operation of the illuminated
entry system can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
xThe illuminated entry system does
not operate in conjunction with the
overhead lights when the overhead
lights are turned on using the
overhead light ON/OFF switch.
Accessory Sockets
▼Accessory Sockets
Only use genuine Mazda accessories
or the equivalent requiring no greater
than 120 W (DC 12 V, 10 A).
The ignition must be switched to ACC
or ON.


CAUTION
¾To prevent accessory socket damage
or electrical failure, pay attention to
the following:
¾Do not use accessories that require
more than 120 W (DC 12 V, 10 A).
¾Do not use accessories that are not
genuine Mazda accessories or the
equivalent.
¾Close the cover when the
accessory socket is not in use to
prevent foreign objects and liquids
from getting into the accessory
socket.
¾Correctly insert the plug into the
accessory socket.
¾Do not insert the cigarette lighter
into the accessory socket.
¾Noise may occur on the audio
playback depending on the device
connected to the accessory socket.
Interior Features
Interior Equipment
5-35

¾Depending on the device connected
to the accessory socket, the vehicle's
electrical system may be affected,
which could cause the warning light
to illuminate. Disconnect the
connected device and make sure
that the problem is resolved. If the
problem is resolved, disconnect the
device from the socket and switch
the ignition off. If the problem is not
resolved, consult an expert repairer
(we recommend an Authorised
Mazda Repairer).
NOTE
To prevent discharging of the battery,
do not use the socket for long periods
with the engine off or idling.
Connecting the accessory socket
1. Open the lid.
2. Pass the connection plug cord
through the cutout of the console
and insert the plug into the
accessory socket.

1. Plug
Cup Holder
▼Cup Holder
WARNING
Never use a cup holder to hold hot
liquids while the vehicle is moving:
Using a cup holder to hold hot liquids
while the vehicle is moving is
dangerous. If the contents spill, you
could be scalded.
Do not put anything other than cups
or drink cans in cup holders:
Putting objects other than cups or
drink cans in a cup holder is
dangerous.
During sudden braking or
manoeuvring, occupants could be hit
and injured, or objects could be
thrown around the vehicle, causing
interference with the driver and the
possibility of an accident. Only use a
cup holder for cups or drink cans.
Interior Features
Interior Equipment
5-36

Scheduled Maintenance
▼Scheduled Maintenance
NOTE
After the prescribed period, continue to follow the described maintenance at the
recommended intervals.
Emission control and related systems
The ignition and fuel systems are highly important to the emission control system
and to efficient engine operation. Do not tamper with them.
All inspections and adjustments must be made by an expert repairer (we
recommend an Authorised Mazda Repairer).
▼Europe
Vehicles utilizing the vehicle status monitor feature (My Mazda Service):
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
For vehicles in European countries, except SKYACTIV-D 1.8 for Ukraine
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval,
20,000 km (12,500 miles) or 12 months, whichever comes first. (after the previous
maintenance)
For SKYACTIV-D 1.8 vehicles in Ukraine
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval,
10,000 km (6,250 miles) or 12 months, whichever comes
first. (after the previous
maintenance)
Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
SKYACTIV-G 2.0 AND SKYACTIV-X 2.0
Engine oil &
filter
*1*2RRRRRRRRRRRR
Spark plugs
*4
SKYACTIV-G
2.0Replace every 120,000 km (75,000 miles).
SKYACTIV-X
2.0Replace every 64,000 km (40,000 miles).
Air filter
*5RRRR
Fuel lines and hoses IIIIII
Hoses and tubes for emission I I I I
SKYACTIV-D 1.8
Engine oil &
filter
*1*3RRRRRRRRRRRR
Maintenance and Care
Scheduled Maintenance
6-3