low beam MAZDA MODEL CX-5 2016 (in English) User Guide

Page 268 of 626

Black plate (268,1)
Forward Sensing Camera (FSC)í
Your vehicle is equipped with a Forward Sensing Camera (FSC). The Forward Sensing
Camera (FSC) is positioned near the rearview mirror and used by the following systems.
lHigh Beam Control System (HBC)lLane Departure Warning System (LDWS)lSmart Brake Support (SBS)
The Forward Sensing Camera (FSC) determines the conditions ahead of the vehicle while
traveling at night and detects traffic lanes. The distance in which the Forward Sensing
Camera (FSC) can detect objects varies depending on the surrounding conditions.
4-134
When Driving
íSome models.
i-ACTIVSENSE
CX-5_8DV2-EA-14K_Edition3 Page268
Thursday, February 26 2015 5:33 PM
Form No.8DV2-EA-14K

Page 269 of 626

Black plate (269,1)
CAUTION
ØDo not apply accessories, stickers or film to the windshield near the Forward
Sensing Camera (FSC).
If the area in front of the Forward Sensing Camera (FSC) lens is obstructed, it will
cause the system to not operate correctly. Consequently, each system may not
operate normally which could lead to an unexpected accident.
ØDo not disassemble or modify the Forward Sensing Camera (FSC).
Disassembly or modification of the Forward Sensing Camera (FSC) will cause a
malfunction or mistaken operation. Consequently, each system may not operate
normally which could lead to an unexpected accident.
ØHeed the following cautions to assure the correct operation of the Forward
Sensing Camera (FSC).
ØThe direction of the Forward Sensing Camera (FSC) has been finely adjusted,
therefore do not change the installation position or remove the Forward
Sensing Camera (FSC).
ØBe careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to
get dirty.
ØDo not remove the Forward Sensing Camera (FSC) cover.
ØDo not place objects on the dashboard which reflect light.
ØAlways keep the windshield glass around the camera clean by removing dirt or
fogging. Use the windshield defroster to remove fogging on the windshield.
ØConsult an Authorized Mazda Dealer regarding cleaning the interior side of the
windshield around the Forward Sensing Camera (FSC).
ØConsult an Authorized Mazda Dealer before performing repairs around the
Forward Sensing Camera (FSC).
ØThe Forward Sensing Camera (FSC) is installed to the windshield. Consult an
Authorized Mazda Dealer for windshield repair and replacement.
ØWhen performing repairs around the rearview mirror, consult an Authorized
Mazda Dealer.
ØDo not hit or apply strong force to the Forward Sensing Camera (FSC) or the
area around it. If strong force is applied, stop using the Lane Departure
Warning System (LDWS), the High Beam Control System (HBC), and Smart
Brake Support (SBS) and consult an Authorized Mazda Dealer.
ØThe direction in which the Forward Sensing Camera (FSC) is pointed has been
finely adjusted. Do not change the installation position of the Forward Sensing
Camera (FSC) or remove it. Otherwise, it could result in damage or malfunction.
When Driving
i-ACTIVSENSE
4-135
CX-5_8DV2-EA-14K_Edition3 Page269
Thursday, February 26 2015 5:33 PM
Form No.8DV2-EA-14K

Page 270 of 626

Black plate (270,1)
NOTElIn the following cases, the Forward Sensing Camera (FSC) cannot detect target objects correctly,
and each system may be unable to operate normally.
lThe height of the vehicle ahead is low.lYou drive your vehicle at the same speed as the vehicle ahead.lHeadlights are not turned on during the night or when going through a tunnel.lIn the following cases, the Forward Sensing Camera (FSC) may not be able to detect target
objects correctly.
lWhen driving next to walls with no patterning (including fences and longitudinally striped
walls).
lThe taillights of the vehicle ahead are turned off.lA vehicle is outside the illumination range of the headlights.lThe vehicle is making a sharp curve, or ascending or descending a steep slope.lEntering or exiting a tunnel.lHeavy luggage is loaded causing the vehicle to tilt.lStrong light is shone at the front of the vehicle (back light or high-beam light from on-coming
vehicles).
lThere are many light emitters on the vehicle ahead.lWhen the vehicle ahead is not equipped with taillights or the taillights are turned off at
nighttime.
lThe vehicle ahead has a special shape.
4-136
When Driving
i-ACTIVSENSE
CX-5_8DV2-EA-14K_Edition3 Page270
Thursday, February 26 2015 5:33 PM
Form No.8DV2-EA-14K

Page 288 of 626

Black plate (288,1)
qDisplayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)
(Actual view)
Object Garnish
Bumper
NOTElThe displayable range varies depending on the vehicle and road conditions.lThe displayable range is limited. Objects under the bumper or around the bumper ends cannot be
displayed.
lThe distance appearing in the displayed image is different from the actual distance because the
rear view parking camera is equipped with a specific lens.
lSome optionally installed vehicle accessories may be picked up by the camera. Do not install any
optional parts that can interfere with the camera view, such as illuminating parts or parts made of
reflective material.
lIt may be difficult to see the display under the following conditions, however, it does not indicate a
malfunction.
lIn darkened areas.lWhen the temperature around the lens is high/low.lWhen the camera is wet such as on a rainy day or during periods of high humidity.lWhen foreign material such as mud is stuck around the camera.lWhen the camera lens reflects sunlight or headlight beams.lImage display may be delayed if the temperature around the camera is low.
4-154
When Driving
Rear View Monitor
CX-5_8DV2-EA-14K_Edition3 Page288
Thursday, February 26 2015 5:33 PM
Form No.8DV2-EA-14K

Page 478 of 626

Black plate (478,1)
Light Bulbs
With LED headlights
With halogen headlights
Rear side-marker lights
Rear turn signal lights
Brake lights/Taillights
License plate lights Headlights (Low beam)
High-mount brake light
Rear side-marker lights
Rear turn signal lights Brake lights/Taillights
License plate lights
High-mount brake light
Side turn
signal lights
Front turn signal lights/
Front side-marker lights
Headlights (High beam)/
Daytime running lights Headlights (Low beam) Front turn signal lights/
Parking lights (Front side-
marker lights)
Fog lights
Rear map lights
Overhead light (Front)/
Map lights Luggage compartment light
Vanity mirror lights
Rear map lights
Overhead light (Front)/
Map lights Luggage compartment light
Vanity mirror lights
Daytime running lights/
Parking lights
Fog lights
Some models.
Side turn
signal lights
Headlights (High beam)
Taillights (Liftgate side)
Taillights (Liftgate side)
Reverse lights
Reverse lights Taillights
6-46
Maintenance and Care
Owner Maintenance
CX-5_8DV2-EA-14K_Edition3 Page478
Thursday, February 26 2015 5:34 PM
Form No.8DV2-EA-14K

Page 479 of 626

Black plate (479,1)
WARNING
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
CAUTION
When removing the lens or lamp unit
using a flathead screwdriver, make
sure that the flathead screwdriver
does not contact the interior
terminal. If the flathead screwdriver
contacts the terminal, a short circuit
may occur.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
qReplacing Exterior Light Bulbs
Headlights (With LED headlights)
Low-beam bulbs, High-beam bulbs,
Daytime running lights/Parking lights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Headlights (With halogen headlights)
Low-beam bulbs, High-beam bulbs/
Daytime running lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.
3.(Right side)
Remove the windshield washer fluid
reservoir from the guide.
Windshield washer
fluid reservoir Guide
4. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
Maintenance and Care
Owner Maintenance
6-47
CX-5_8DV2-EA-14K_Edition3 Page479
Thursday, February 26 2015 5:34 PM
Form No.8DV2-EA-14K

Page 480 of 626

Black plate (480,1)
Low-beam bulbs
High-beam bulbs/Daytime running
lights
5. Turn the socket and bulb assembly to
remove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.Low-beam bulbs
High-beam bulbs/Daytime running
lights
6. Install the new bulb in the reverse order
of the removal procedure.
Front turn signal lights/Front side-
marker lights (With LED headlights)
Front turn signal lights/Parking lights
(Front side-marker lights) (With
halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
6-48
Maintenance and Care
Owner Maintenance
CX-5_8DV2-EA-14K_Edition3 Page480
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K

Page 491 of 626

Black plate (491,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
18 WIPER 20 A Front window wiper and washer
19 HEATER 40 A Air conditioner
20 DCDC REG 30 A―
21 ENGINE.IG1 7.5 A Engine control system
22 C/U IG1 15 A For protection of various circuits
23H/L LOW L
HID L15 A Headlight low beam (LH)
24 H/L LOW R 15 A Headlight low beam (RH)
25 ENGINE3 15 A Engine control system
26 ENGINE2 15 A Engine control system
27 ENGINE1 15 A Engine control system
28 AT 15 A Transaxle control system
í, Ignition switch
29 H/CLEAN 20 A―
30 A/C 7.5 A Air conditioner
31 AT PUMP 15 A Transaxle control system
í
32 STOP 10 A Brake lights
33 R.WIPER 15 A Rear window wiper
34 H/L HI 20 A Headlight high beam
35 HID R 15 A―
36 FOG 15 A Fog lights
í
377.5 A Engine control system
38 AUDIO2 7.5 A Audio system
39 GLOW SIG 5 A―
40 METER2 7.5 A―
41 METER1 10 A Instrument cluster
42 SRS1 7.5 A Air bag
43 BOSE 25 A Bose
®Sound System-equipped modelí
44 AUDIO1 15 A Audio system
45 ABS/DSC S 30 A ABS, Dynamic stability control system
46 FUEL PUMP 15 A Fuel system
47 FUEL WARM 25 A―
48 TAIL 15 A Taillights, License plate lights
49 FUEL PUMP2 25 A―
50 HAZARD 25 AHazard warning flashers, Turn signal lights, Parking lights
(Front side-marker lights)
51 DRL 15 A Daytime running lights
í
52 R.OUTLET2 15 A Accessory sockets
53 HORN 15 A Horn
54 ROOM 15 A Overhead light
Maintenance and Care
Owner Maintenance
6-59íSome models. CX-5_8DV2-EA-14K_Edition3 Page491
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K

Page 533 of 626

Black plate (533,1)
“Key not detected”is displayed
This message is displayed when any of
the following operations is performed
with the key out of the operational range
or placed in areas inside the cabin where it
is difficult for the key to be detected.
lThe push button start is pressed with
the ignition switched off
lThe ignition is switched onlAll doors are closed without switching
the ignition off
Type B
If any malfunction occurs in the keyless
entry system, it illuminates continuously.
CAUTION
If the key warning indicator light
illuminates or the push button start
indicator light (amber) flashes, the
engine may not start. If the engine
cannot be started, try starting it
using the emergency operation for
starting the engine, and have the
vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
Refer to Emergency Operation for
Starting the Engine on page 4-8.
qIf the high beam control system
(HBC) warning light (amber)
flashes
í
This light turns on if there is a
malfunction in the high beam control
system (HBC). Have your vehicle
inspected by an Authorized Mazda
Dealer.
qIf the wrench indication/indicator
light is indicated
Type A
Perform maintenance in accordance with
the message.
Type B
The wrench indicator light illuminates
when the engine oil replacement period is
reached.
If the light is illuminated, replace the
engine oil.
Refer to Engine Oil on page 6-27.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-31íSome models. CX-5_8DV2-EA-14K_Edition3 Page533
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K

Page 605 of 626

Black plate (605,1)
qAir Conditioner
The type of refrigerant used is indicated on a label attached to the inside of the engine compartment. Check the
label before recharging the refrigerant. Refer to Climate Control System on page 5-2.
Item Classification
Refrigerant Type HFC134a (R-134a)
qLight Bulbs
Exterior light
Light bulbCategory
Wattage UNECE
*1(SAE)
HeadlightsHalogen
headlightsHigh beam 60 HB3 (9005)
Low beam 55 H11 (H11)
LED headlightsHigh beam LED
*2―(―)
Low beam LED*2―(―)
Daytime running lightsWith halogen
headlights60 HB3 (9005)
Daytime running lights/Parking
lightsWith LED headlights LED
*2―(―)
Front turn signal lights/Parking
lights (Front side-marker lights)With halogen
headlights27/8―(1157NA)
Front turn signal lights/Front
side-marker lightsWith LED headlights 28/8―(7444NA)
Fog lights
íWith halogen
headlights55 H11 (H11)
With LED headlights LED
*2―(―)
Side turn signal lights LED*2―(―)
High-mount brake light LED*2―(―)
Rear turn signal lights 21 WY21W (7443NA)
Brake lights/TaillightsWith halogen
headlights21/5 W21/5W (7443)
With LED headlights LED
*2―(―)
Taillights (Liftgate side)With halogen
headlights5 W5W (―)
With LED headlights LED
*2―(―)
Rear side-marker lightsWith halogen
headlights5 W5W (―)
With LED headlights LED
*2―(―)
Reverse lights 18 W16W (921)
License plate lights 5 W5W (―)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
Specifications
9-7íSome models. CX-5_8DV2-EA-14K_Edition3 Page605
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K

Page:   < prev 1-10 11-20 21-30 next >