warning MAZDA MODEL CX-5 2017 Owner's Manual - RHD (UK, Australia) (in English)

•The following settings for the
LAS&LDWS can be changed. Refer to
Personalisation Features on page 9-
12.
•Steering operation assist operational/
non-operational
•Cancel sensitivity (likelihood of
steering assist)
Vehicle lane line display
When the LAS&LDWS becomes
operational while on standby, the vehicle
lane lines are displayed in the
multi-information di splay and the active
driving display. In the vehicle lane lines
display indicating the operation status, the
colour of the vehicle lane lines being
detected changes to white.
(Stand-by status)
Multi-information Display
Active Driving Display
(Operational status)
Multi-information Display
Active Driving Display
Auto cancel
In the following cases, the LAS&LDWS is
automatically cancelled, the LAS&LDWS
warning indication (amber) turns on, and
an alert is displayed. When the
LAS&LDWS become operational, the
system turns back on automatically.
•The temperature inside the camera is
high or low.
•The windscreen around the camera is
foggy.
•The windscreen around the camera is
blocked by an obstruction, causing poor
forward visibility.
Auto cancel of warning/steering assist
When the following operations are
performed, the LAS& LDWS operation is
cancelled automatically. The LAS&LDWS
resumes automatically after the operation.
•The steering wheel is operated abruptly.
•The brake pedal is operated.
•The accelerator pedal is operated.
(To cancel the automatic sensitivity
cancel function, deselect “Cancel
sensitivity” in the personalisation
features setting.)
•The direction indicator lever is operated.
•The vehicle crosses a lane line.
NOTE
•After the operation, the LAS&LDWS
operation may not operate for a period
of 5 seconds at the most until the lane
lines are detected.
•Under the following conditions, the
LAS&LDWS cancels the warning/
steering assist automatically.
When Driving
i-ACTIVSENSE
4-168
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•The driver takes his/her hands off the
steering wheel.
(The LAS&LDWS is designed to assist
the driver's steering operation and it
will resume operation automatically
when the driver holds the steering
wheel.)
•The TCS OFF switch is pressed to
cancel the TCS.
Steering operation assist OFF
(non-operational)
The steering operation assist for the
LAS&LDWS can be changed to
non-operational (OFF).
Refer to Setting Cha nge (Personalisation
Features) on page 9-12.
When the steering operation assist has
been changed to non-operational (OFF),
the operation conditions and the display of
the LAS&LDWS differ. Operate the
system as follows:
System operation
Make sure that the LAS&LDWS OFF
indicator light in the instrument cluster is
turned off. When t he LAS&LDWS OFF
indicator light turns on, press the switch
and make sure that the indicator light turns
off.
Drive the vehicle in the centre of the
driving lane while the LAS&LDWS OFF
indicator light in the instrument cluster is
turned off.
The system becomes operational when all
of the following conditions are met.
•The system detects white (yellow) lane
lines on both the right and left sides or
on either side.
•The vehicle speed is about 60 km/h (37
mph) or faster.
•The vehicle is driven on a straight road
or road with gentle curves.
•The engine is running.
The LAS&LDWS goes on stand-by status
in the following cases:
•The system cannot detect white (yellow)
lane lines.
•The vehicle speed is less than about 60
km/h (37 mph).
•The vehicle is making a sharp curve.
•The vehicle is making a curve at an
inappropriate speed.
NOTE
•The LAS&LDWS remains on stand-by
until it detects white (yellow) lines on
both the left and right sides, or on either
side.
•When the system detects a white
(yellow) lane line on one side only, the
system will not activ ate warnings for the
lane line on the side that is not being
detected.
When Driving
i-ACTIVSENSE
4-169
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•The distance and warning sensitivity
(likelihood of a warning) which the
system uses to determine the possibility
of a lane departure can be changed.
Refer to Setting Change
(Personalisation Features) on page 9-
12.
Vehicle lane line display
When the LAS&LDWS becomes
operational while on standby, the vehicle
lane lines are displayed in the
multi-information display. The system
changes to operational status display when
the system detects a white (yellow) line on
either the left or right.
(Stand-by status)
(Operational status)
Auto cancel
In the following cases, the LAS&LDWS is
automatically cancelled, the LAS&LDWS
warning indication (amber) turns on, and
an alert is displayed. When the
LAS&LDWS become operational, the
system turns back on automatically.
•The temperature inside the camera is
high or low.
•The windscreen around the camera is
foggy.
•The windscreen around the camera is
blocked by an obstruction, causing poor
forward visibility.
(Auto cancel of warnings)
When the following operations are
performed, the LAS&LDWS determines
that the driver intends to make a lane
change and the system operation is
cancelled automatically. The LAS&LDWS
resumes automatically after the operation.
•The steering wheel is operated abruptly.
•The brake pedal is depressed.
•The accelerator pedal is depressed.
(To cancel the automatic sensitivity
cancel function, deselect “Warning
sensitivity” in the personalisation
features setting.)
•The direction indicator lever is operated.
•The vehicle crosses a lane line.
When Driving
i-ACTIVSENSE
4-170
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Lane Departure Warning
If the system determines that the vehicle may deviate from its
lane, the lane departure
warning (beep sound, rumble sound
*1, or steering wheel vibration) is activated and the
direction in which the system determines that the vehicle may d eviate is indicated in the
multi-information display or the active driving display.
For vehicles equipped with the m ulti-information display, the direction which the system
determined that the vehicle may be deviating from its lane is indicated in the
multi-information display.
For vehicles equipped with the act ive driving display, the colour of the lane line in the
direction which the system determined that the vehicle may be d eviating from its lane
changes from white to amber and the vehicle lane line flashes.
Multi-information Display Active Driving Display
NOTE
•If you have set the lane departure warning sound to the beep sound/rumble sound*1
setting, the warning sound may not be heard depending on the surrounding noise
conditions.
•If you have set the lane departure warning system to the steering wheel vibrations setting,
the vibration may not be felt dependi ng on the road surface conditions.
•When the setting for the steering operation assist is changed to operational, the warnings
can be set to activate/not activate. (When the setting for the steering operation assist is
changed to non-operational, the warnings cannot be set to not activate.)
Refer to Setting Change (Personalisation Features) on page 9-12.
•The LAS&LDWS can be changed to the following settings regardless of whether the
steering operation assist has been set to operational/non-operational. Always check the
setting status when driving the vehicle and make setting changes if necessary.
Refer to Setting Change (Personalisation Features) on page 9-12.
•Steering wheel vibr ation: Strong/weak
•Warning sound volume
•Types of warnings (steering wheel vibration/beep sound/rumble sound*1)
*1 A rumble strip is a series of grooves in the road pavement surface positioned at specific
intervals, and when the vehicle passes over it a vibration and rumble sound is produced
which alerts the driver that the vehicle is departing from the lane.
When Driving
i-ACTIVSENSE
4-172
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Adjustable Speed Limiter (ASL) M
ain Indication (White)/Adjustable Speed
Limiter (ASL) Set Indication (Green)
The indication has two colours.
ASL main indication (white)
The indication is display in white when the MODE switch is pres sed and the ASL is
activated.
ASL set indication (green)
The indication is display in green when a speed has been set.
▼ Speed Limiter Warning Beep
Instrument cluster type A
If the vehicle speed exceeds the set speed by about 5 km/h (3 mph) or faster, the background
of the ASL set speed indication turns amber and flashes three t
imes. In addition, a warning
sound is activated at the same time. The indication stops flash ing and remains on if the
vehicle speed continues to exceed the set speed by about 5 km/h (3 mph) or faster, and the
indication and warning sound remain on until the vehicle is dri ven at the set speed or slower.
Instrument cluster type B
If the vehicle speed exceeds the set speed by about 5 km/h (3 mph) or more, a warning
sound operates continuously and the ASL display flashes at the same time. The warning
sound operates and the display flashes until the vehicle speed decreases to the set speed or
less.
Verify the safety of the surrounding area and adjust the vehicl e speed by applying the
brakes. Additionally, keep a safer distance from the vehicles b ehind you.

Active Driving Display With Multi-
information DisplayWithout Multi-
information Display
When Driving
i-ACTIVSENSE
4-177
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

CAUTION
(With cruise control)
If the set speed is set lower than the current vehicle speed by pressing the SET
or RES/
switch, the warning beep is not activated for about 30 seconds even if the vehicle speed is
faster than the newly set speed by 5 km/h (3 mph). Be careful not to drive over the set speed.
(With Mazda Radar Cruise Control (MRCC) or Mazda Radar Cruise Control with Stop & Go
function (MRCC with Stop & Go function))
If the set speed is set lower than the current vehicle speed by pressing the SET
or RES switch,
the warning beep is not activated for about 30 se conds even if the vehicle speed is faster than
the newly set speed by 5 km/h (3 mph). Be careful not to drive over the set speed.
NOTE
When the system is temporarily cancelled by depressing the accelerator pedal fully, the ASL
display shows the cancel display. If the vehicle speed exceeds the set speed by about 5 km/h
(3 mph) or more while the cancel display is displayed, the set speed display flashes but the
warning sound is not operated.
▼ Activation/Deactivation
NOTE
When the ignition is switched of
f, the system status before it was turned off is maintained.
For example, if the ignition is switched off while the ASL is operating, the system will be
operable when the ignition is switched ON the next time.
Activation
Press the MODE switch to operate the system. The ASL screen is displayed, and the ASL
main indication displays in white.
NOTE
When the cruise control, Mazda Radar Cruise Control (MRCC), or Mazda Radar Cruise
Control with Stop & Go function (MRCC with Stop & Go function) system becomes
operable after pressing the MODE switch, press the mode switch again to switch to the ASL.
Deactivation
To deactivate the system, do the following operations:
When a cruising speed h as been set (ASL set indication displays in green)
Long-press the OFF/CAN switch or press the OFF/CAN switch 2 times. The ASL screen is
no longer displayed and the ASL set indication (green) does not display.
When Driving
i-ACTIVSENSE
4-178
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Advanced Smart City Brake Support (Advanced SCBS)
(Except Indonesia and Taiwan)
*
The Advanced SCBS alerts the driver of a possible collision usi ng the display and a warning
sound when the Forward Sensing Camera (FSC) detects a vehicle a head or pedestrian and
determines that a collision with the object is unavoidable whil e the vehicle is driven at a
vehicle speed of about 4 to 80 km/h (2 to 50 mph) if the object is a vehicle ahead and about
10 to 80 km/h (6.2 to 50 mph) if the object is a pedestrian. In addition, the system reduces
damage in the event of a collision by operating the brake contr ol (Advanced SCBS brake)
when the system determines that a collision is unavoidable. In addition, when the driver
depresses the brake pedal, the brakes are applied firmly and qu ickly to assist. (Brake Assist
(Advanced SCBS brake assist))

Forward Sensing
Camera (FSC)
WA R N I N G
Do not rely completely on the Advanced SCBS system:
 The Advanced SCBS system is only designed to reduce damage in the event of a collision.
Over reliance on the system leading to the accelerator pedal or brake pedal being
mistakenly operated could result in an accident.
 The Advanced SCBS system operates in response to a vehicle ahead or a pedestrian. The
system does not operate in response to obstru ctions such as a wall, 2-wheeled vehicles, or
animals.
When Driving
i-ACTIVSENSE
*Some models.4-181
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

CAUTION
In the following cases, turn the system off to prevent a mis-operation:
The vehicle is being towed or when towing another vehicle.
 The vehicle is on a chassis roller.
 When driving on rough roads such as in areas of dense grass or off-road.
Refer to Stopping the Advanced Smart City Brake Support (Advanced SCBS) System Operation
on page 4-184 on how to turn off the Advanced SCBS system.
NOTE
•The Advanced SCBS system will operate under the following conditions.
•The engine is running.
•The Smart City Brake Support (SCBS) warning light (amber) does not illuminate.
•(Object is vehicle ahead)
The vehicle speed is between about 4 to 80 km/h (2 to 50 mph).
•(Object is a pedestrian)
The vehicle speed is between about 10 to 80 km/h (6.2 to 50 mph).
•The Advanced SCBS system is not turned off.
•Under the following conditions, the Advanced SCBS system may not operate normally:
•The Advanced SCBS system will not operate if the driver is deliberately performing
driving operations (accelerator pedal and steering wheel).
•If there is the possibility of pa rtial contact with a vehicle ahead.
•The vehicle is driven on a slippery road surface such as wet roads or icy or snow-bound
roads.
•The braking performance is adversely affected due to cold temperatures or wet brakes.
•The vehicle is driven at the same speed as the vehicle ahead.
•The accelerator pedal is depressed.
•The brake pedal is depressed.
•The steering wheel is being operated.
•The selector lever is being operated.
•In the following cases, the Advanced SCBS may operate.
•Objects on the road at the entrance to a curve.
•Vehicles passing in the opposite lane while making a curve.
•When passing through a toll gate.
•When passing through low gates, narrow gates, car washing machines, or tunnels.
•If you suddenly come close to a vehicle ahead.
•2-wheeled vehicles, animals, or standing trees.
When Driving
i-ACTIVSENSE
4-182
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•(Manual transaxle)
If the vehicle is stopped by the SCBS operation and the clutch pedal is not depressed, the
engine stops.
▼Smart City Brake Support (SCBS)
Indicator Light (Red)
If the Advanced SCBS is operating, the
indicator light (red) flashes.

▼Collision Warning
If there is the possibili
ty of a collision with
a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the multi-information di splay or the active
driving display.
Multi-information Display
Active Driving Display
NOTE
The operation distance and volume of the
collision warning can be changed. Refer
to Personalisation Features on page 9-
12.
▼ Automatic Brake Operation Display
“SCBS Automatic Brake” is indicated in
the multi-informatio
n display after the
Advanced SCBS brakes or the brake assist
(Advanced SCBS brake assist) is operated.
NOTE
•The collision warning beep sounds
intermittently while the Advanced SCBS
brake or brake assist (Advanced SCBS
brake assist) is operating.
•If the vehicle is stopped by the Advanced
SCBS operation and the brake pedal is
not depressed, the warning beep sounds
one time after about 2 seconds and the
Advanced SCBS brake is automatically
released.
When Driving
i-ACTIVSENSE
4-183
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Smart City Brake Support [Forward] (SCBS F)
(Indonesia and Taiwan)
*
The SCBS F system alerts the dri ver of a possible collision using an indication in the
display and a warning sound when the Forward Sensing Camera (FS C) detects a vehicle
ahead and determines that a collis ion with a vehicle ahead is u navoidable while the vehicle
is being driven at a vehicle speed of about 4 to 80 km/h (2 to 50 mph). In addition, the
system reduces damage in the event of a collision by operating the brake control (Smart City
Brake Support (SCBS) brake) when the system determines that a c ollision is unavoidable
while the vehicle is being driven at a vehicle speed of about 4 to 30 km/h (2 to 18 mph). It
may also be possible to avoid a collision if the relative speed between your vehicle and the
vehicle in front of you is less than about 20 km/h (12 mph). In addition, when the driver
depresses the brake pedal while the system is in the operation range at about 4 to 30 km/h (2
to 18 mph), the brakes are applied firmly and quickly to assist . (Brake Assist (Smart City
Brake Support (SCBS) brake assist))

Forward Sensing
Camera (FSC)
WA R N I N G
Do not rely completely on the SCBS F system:
 The SCBS F system is only designed to reduce damage in the event of a collision. Over
reliance on the system leading to the accele rator pedal or brake pedal being mistakenly
operated could result in an accident.
 The SCBS F is a system which operates in resp onse to a vehicle ahead. The system may not
be able to detect or react to 2-wheeled vehicles or pedestrians.
When Driving
i-ACTIVSENSE
*Some models.4-185
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2