MAZDA MODEL MPV 2002 Owners Manual (in English)

8-29
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
9. Install in the reverse order of removal.
NOTE
•When reinstalling the sealing cover,
make sure faces up.
•Use the protective cover and carton
to dispose of the old bulb promptly
out of the reach of children.
J16L_EA.book Page 29 Friday, February 22, 2002 11:34 AM

8-30
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K

Replacing a Bulb (Front)
To replace the parking light bulbs, contact an Authorized Mazda Dealer.
Fog lights
Front turn signal lights/
Side-marker lights
J16L_EA.book Page 30 Friday, February 22, 2002 11:34 AM

8-31
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K

Replacing a Bulb (Interior)
O
NO
F
F
Overhead lights/Map lights
(Without sunroof, with overhead console)
Overhead lights/Map lights
(Without either sunroof or overhead console)Overhead lights
Courtesy lights
Luggage compartment light Overhead lights/Map lights
(With sunroof)
J16L_EA.book Page 31 Friday, February 22, 2002 11:34 AM

8-32
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K

Replacing a Bulb (Rear)
Brake lights/Taillights
Rear turn signal lights
Reverse lights
TaillightsHigh-mount brake lights
License plate lights
An unsecured high-mount brake lights
will allow water to leak into the vehicle.
Make sure the high-mount brake light is
tightly fastened to the vehicle and if
water still leaks, consult an Authorized
Mazda Dealer.
J16L_EA.book Page 32 Friday, February 22, 2002 11:34 AM

8-33
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
Yo u r v e h i c l e’s electrical system is
protected by fuses.
If any lights, accessories, or controls don’t
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.

Fuse Replacement
If the electrical system doesn’t work, first
inspect fuses on the driver’s side.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover.3. Pull the fuse straight out with the fuse
puller provided on the fuse panel.
4. Inspect it and replace if it’s blown.
5. Push in a new fuse of the same rating,
and make sure it fits tightly. If it
doesn’t, have an Authorized Mazda
Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO circuit.
Fuses
Fuse panel cover
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Fuse puller
Normal Blown
CAUTION
J16L_EA.book Page 33 Friday, February 22, 2002 11:34 AM

8-34
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
If the headlights or other electrical
components don’t work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new
one of the same rating
.When replacing the 120A fuse:
1. Turn off the ignition switch.
2. Remove the negative battery terminal.
3. Remove the A nuts.
4. Lift the fuse block and remove the B
bolts.
5. Replace the fuse with a new one of the
same rating
.
6. Install in the reverse order of removal.
Fuse block cover
Ta b
Normal Blown
120A fuse
A
A BB
J16L_EA.book Page 34 Friday, February 22, 2002 11:34 AM

8-35
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K

Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 DEFOG 40ARear window
defroster
2 BTN 60ASTOP, HAZARD,
ROOM, D.LOCK
and DRL fuses
3 ABS 60AAntilock brake
system,
For protection of
various circuits
4 FAN1 30A Cooling fan
5 FAN2 30A Cooling fan
6 HEATER 40A Heater
7 R.HEATER 30ARear heater,
For protection of
various circuits
8 IG KEY2 40AA/C, P.WIND,
SUN ROOF and
R.WIP fuses
9 A/C 10AAir conditioner,
For protection of
various circuitsDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
10 TAIL 15A Taillights
11 (A/C PWR) 15A Inverter
12 HORN 15A Horn
13 (FOG) (15A)For protection of
various circuits
14 EEC 5AFor protection of
various circuits
15 HEAD L 15A Headlight-left
16 HEAD R 15A Headlight-right
17 (HID L) (20A)—
18 (HID R) (20A)—
19 IG KEY1 60AMETER,
ENGINE and
WIPER fuses
20 EGI INJ 30AFor protection of
various circuits
21 FUEL PUMP 20A Fuel pump
22 MAIN 120AFor protection of
all circuits
J16L_EA.book Page 35 Friday, February 22, 2002 11:34 AM

8-36
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
Fuse block (Driver’s side)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 (P.WIND) 30APower windows,
For protection of
various circuits
2 WIPER 20A
Wi n ds h i e l d
wipers and washer
3(SUN
ROOF)15ASunroof,
For protection of
various circuits
4 R.WIP 10ARear window
wiper and washer
5 (SEAT) 20AFor protection of
various circuits
6 (M.DEF) 10AMirror defroster,
For protection of
various circuits
7 (A/C) 10AAir conditioner,
For protection of
various circuits
8 (DRL) 10AFor protection of
various circuits
9—— —
10 (H/CLEAN) 20AFor protection of
various circuits
11—— —
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
12 HAZARD 10AHazard warning
flashers
13 ROOM 15AOverhead lights,
Map lights,
Luggage
compartment light
14(AUX
POWER)25A Accessory socket
15(CLOSER
LH)20AFor protection of
various circuits
16 (AUDIO) 10AAudio system, For
protection of
various circuits
17 (D.LOCK) 30APower door locks,
For protection of
various circuits
18 (P/SEAT) 30A Power seat
19 ENGINE 10AEngine control
system
20 METER 10A Instrument cluster
21 STOP 15A Brake lights
22(CLOSER
RH)20AFor protection of
various circuits
J16L_EA.book Page 36 Friday, February 22, 2002 11:34 AM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
23(ACC.
DELAY)30APower windows
delay,
For protection of
various circuits
24 METER 15AInstrument
cluster,
INH switch
25 (ST.SIGN) 10A Starter signal
26 CIGAR 25A Lighter
27—— —
28—— —
J16L_EA.book Page 37 Friday, February 22, 2002 11:34 AM

8-38
Maintenance and Care
Form No. 8Q44-EA-01K
Appearance Care
The paintwork on your Mazda represents
the latest technical developments in
composition and methods of application.
Environmental hazards, however, can
harm the paint’s protective properties, if
proper care is not taken.
Here are some examples of possible
damage, with tips on how to prevent them.

Etching Caused by Acid Rain or
Industrial Fallout
Occurrence
Industrial pollutants and vehicle
emissions drift into the air and mix with
rain or dew to form acids. These acids can
settle on a vehicle’s finish. As the water
evaporates, the acid becomes concentrated
and can damage the finish.
And the longer the acid remains on the
surface, the greater the chance is for
damage.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you suspect that acid rain has settled on
your vehicle’s finish.

Damage Caused by Bird
Dropping, Insects, or Tree Sap
Occurrence
Bird droppings contain acids. If these
aren’t removed they can eat away the clear
and color base coat of the vehicle’s
paintwork.
When insects stick to the paint surface
and decompose, corrosive compounds
form. These can erode the clear and color
base coat of the vehicle’s paintwork if
they are not removed.
Tree sap will harden and adhere
permanently to the paint finish. If you
scratch the sap off while it is hard, some
vehicle paint could come off with it.
Prevention
It is necessary to have your Mazda
washed and waxed to preserve its finish
according to the instructions in this
section. This should be done as soon as
possible.
Bird droppings can be removed with a soft
sponge and water. If you are traveling and
these are not available, a moistened tissue
may also take care of the problem. The
cleaned area should be waxed according
to the instructions in this section.
Insects and tree sap are best removed with
a soft sponge and water or a commercially
available chemical cleaner.
Another method is to cover the affected
area with dampened newspaper for one to
two hours. After removing the newspaper,
rinse off the loosened debris with water.
How to Minimize
Environmental Paint
Damage
J16L_EA.book Page 38 Friday, February 22, 2002 11:34 AM