display MAZDA MODEL MX-30 EV 2022 Service Manual

Active Driving Display
▼Active Driving Display
1. Display
2. Dust-proof sheet
WARNING
Always adjust the display brightness
and position with the vehicle stopped:
Adjusting the display brightness and position while driving the vehicle is dangerous
as doing so could distract your attention from the road ahead and lead to an
accident.
CAUTION
 Do not place beverages near the dust-proof sheet of the active driving display. If
water or other liquids are splashed on the dust-proof sheet, it could cause
damage.
 Do not place objects or apply stickers above the active driving display or to the
dust-proof sheet as they will cause interference.
NOTE
Wearing polarized sunglasses wi ll reduce the visibility of the active driving display
due to the characteristics of the display.
If the battery has been removed and re-insta lled or the battery voltage is low, the
adjusted position may deviate.
The display may be difficult to view or temporarily
aff ected by weather conditions
such as rain, snow, light, and temperature.
If the audio system is removed, the active driving display cannot be operated.
The active driving display indicates the following information:
Lane Departure Warning System (LDWS) Warnings*
When Driving
Instrument Cluster and Display
4-24*Some models.
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Refer to Lane Departure Warning System (LDWS) on page 4-86.Blind Spot Monitoring (BSM) Operation Conditions and Warnings*
Refer to Blind Spot Monitoring (BSM) on page 4-87.Traffic Sign Recognition System (TSR) tra ffic signs and Warnings*
Refer to Tra ffic Sign Recognition System (TSR) on page 4-93.Front Cross
Traffic Alert (FCTA) Operation Conditions and Warning*
Refer to Front Cross Tra
ffic Alert (FCTA) on page 4-104.Mazda Radar Cruise Contro l with Stop & Go function (MRCC with Stop & Go
function) Operation Co nditions and Warnings*
Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop
& Go function) on page 4-111.
Tra ffic Jam Assist (TJA) Operation Conditions and Warnings*
Refer to Tra
ffic Jam Assist (TJA) on page 4-118.Lane-keep Assist System (LAS) Warnings*
Refer to Lane-keep Assist System (LAS) on page 4-127.Emergency Lane Keeping (ELK) Warnings*
Refer to Emergency Lane Keeping (ELK) on page 4-129.Smart Brake Support (SBS) Operation Conditions and Warnings
Refer to Smart Brake Support (SBS) on page 4-136.
Cruise Control Operation Conditions
Refer to Cruise Control on page 4-176.
Navigation Guidance (vehicles with navigation system)Intersection Name (vehicles with navigation system)Street name (vehicles with navigation system)Lane Guidance (vehicles with navigation system)Speed limit indicator (vehicles with navigation system)Vehicle Speed
The active driving display settings can be changed or adjusted.
Refer to the Settings section in the Mazda Connect Owner's Manual.
NOTE
The desired driving position (display position, brightness level, display
information) can be called up after programming the position.
Refer to Driving Position Memory on page 2-10.
The street name may not be displayed depending on the market and region.
When Driving
Instrument Cluster and Display
*Some models.4-25
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

1. Shift position indication

When the power switch is switched
ON, the shift position is displayed in
the instrument cluster.
In the following cases, the shift
position is displayed in the instrument
cluster even if the power switch is in a
position other than ON.
The AUTO P (parking lock) function
is operating.
Neutral hold mode (automatic car
wash mode) is operating.
Shift guide indication
When the shift position and the
selector lever set position differ, the
shift position and the selector lever set
position are displayed.
1. Shift guide indication
2. Selector lever set position
3. Shift position

The shift guide indication is displayed
under the following conditions.
The selector lever is shifted to the P
position while driving (vehicle speed
of about 5 km/h (4 mph) or faster)
with the selector lever in the D
position.
The selector lever is shifted to the R
position while driving forward
(vehicle speed of about 10 km/h
(6.3 mph) or faster) with the selector
lever in the D position.
The selector lever is shifted to the D
position while driving in reverse
(vehicle speed of about 10 km/h
(6.3 mph) or faster) with the selector
lever in the R position.
The AUTO P (parking lock) function
is operating.
While neutral hold mode (automatic
car wash mode) is operating , the
selector lever is shifted from the N
position to the D or R position.
NOTE
In the following cases, the shift
position and the selector lever set
position di ffer, however, the shift
guide indication is not displayed.
The selector lever is shifted from
the N position to the D or R
position with the brake pedal not
depressed.
When the power switch is switched
ON or from ACC to OFF, the shift
guide indication displayed after
operating the AUTO P (parking lock)
function turns on for about 40
seconds and then it turns off.
When Driving
Selector Lever Position Functions
4-27
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

The driver’s seat belt is unfastened and the driver’s door is opened.
NOTE
When the AUTO P (parking lock) function operates, only the shift position changes
to the P position automatically. The shift po sition indication in the instrument cluster
will di ffer from the selector lever position because the selector lever position does
not change. Check the shift position indication in the instrument cluster and shift the
selector lever to the P position.
Neutral hold mode (autom atic car wash mode)
When in neutral hold mode (automatic car wash mode), a condition is maintained
for about 25 minutes in which the power switch is switched to ACC, the shift
position is in the N position, and the parking brake is released.
Use this mode when it is necessary to release the parking brake and change the shift
position to the N position, such as in an automatic car wash that moves the vehicle
by placing the front and rear tires on one side of the vehicle on a belt conveyor.
Operating neutral hold mode (automatic car wash mode)
Perform any of the following operations when the selector lever is in the N position
with the power switch switched ON (EV system on).
Operation method 1
1. Press the power switch with the brake pedal depressed to start the EV system.
2. Release the parking brake.
3. Shift the selector lever to the N position.
4. Turn o ff the AUTOHOLD.
5. Press the Electric Parking Brake (EPB) switch continuously for 2 seconds or longer (until a sound is activated).
6. Release the EPB switch and press the pow er switch within 5 seconds after the
sound was activated.
Operation method 2
1. Press the power switch with the brake pedal depressed to start the EV system.
2. Release the parking brake.
3. Shift the selector lever to the N position.
4. Turn o ff the AUTOHOLD.
5. Press the power switch with the EPB switch pressed and held while the brake
pedal is not depressed.
NOTE
When the selector lever is shifted from the N position to the D or R position while
neutral hold mode (automatic car wash mode) is operating , a message is displayed
on the multi-information display and the warning beep is activated.
Canceling neutral hold mode (automatic car wash mode)
If any of the following operations is performed, neutral hold mode (automatic car
wash mode) is canceled.
When Driving
Selector Lever Position Functions
4-29
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

When using an automatic car wash
which moves the vehicle with the
front tires mounted, it is necessary to
cancel the parking brake auto
operation before the vehicle enters
the automatic car wash. For details,
refer to Canceling the parking brake
automatic operation.
Release the parking brake and use
neutral hold mode (automatic car
wash mode) when it is necessary to
change the shift position to the N
position for an automatic car wash.
Refer to Selector Lever Operation on
page 4-28.
Manual operation
Applying the parking brake manually
When the brake pedal is firmly
depressed and the EPB switch is pulled
up, the parking brake is applied
regardless of the power switch
position. When the parking brake is
applied, the EPB indicator light in the
instrument cluster and the EPB switch
indicator light turn on.
Releasing the parking brake manually
When the parking brake is firmly
depressed and the EPB switch is
pressed with the power switch
switched ON, the parking brake is
released. When the parking brake is
released, the EPB indicator light in the
instrument cluster and the EPB switch
indicator light turn off .
If the EPB switch is pressed without
depressing the brake pedal, a message
is displayed on the multi-information
display to notify the driver to depress
the brake pedal.
Refer to Message Indicated on
Multi-information Display on page
7-33.
Auto operation
Applying the parking brake
automatically
When the power switch is switched
from ON to ACC or OFF, the parking
brake will be applied automatically.
When the parking brake is applied, the
EPB indicator light in the instrument
cluster and the EPB switch indicator
light turn on.
NOTE
To release the parking brake when
the power switch is switched OFF, it
is necessary to cancel the parking
brake auto operation. For details,
refer to Canceling the parking brake
automatic operation.
When the power switch is switched
from ON to ACC while in neutral
hold mode (automatic car wash
mode), the parking brake is applied
automatically.
When Driving
Brake
4-54
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

AUTOHOLD
▼AUTOHOLD
The AUTOHOLD function automatically holds the vehicle stopped, even if you take
your foot
off the brake pedal. This function can be best used while stopped in
traffic
or at a traffic light. The brakes are released when you start driving the vehicle.
WARNING
Do not rely completely on the AUTOHOLD function:
The AUTOHOLD function is only designed to assist the brake operation while the
vehicle is stopped. Neglecting to operate the brakes and relying only on the
AUTOHOLD system is dangerous and could result in an unexpected accident if the
vehicle were to suddenly move. Operate the brakes appropriately in accordance
with the road and surrounding conditions.
Do not release your foot from the brake pedal while the vehicle is stopped on a
steep grade:
Because there is a possibility of the vehicl
e not being held in the stopped position by
the AUTOHOLD function, the vehicle may move unexpectedly and result in an
accident.
Do not use the AUTOHOLD function on slippery roads such as icy or
snow-covered roads, or unpaved roads:
Even if the vehicle is held in the stopped position by the AUTOHOLD function, the
vehicle may move unexpectedly and result in an accident. Operate the accelerator
pedal, brakes, or steering wheel appropriately as necessary.
Immediately depress the brake pedal in the following cases:
Because the AUTOHOLD function is canceled forcibly, the vehicle may move
unexpectedly and result in an accident.
 “Depress Brake Pedal. Brake Hold Disabled” is displayed in the multi-information
display and the warning sound is activated at the same time.
Always apply the parking brake when parking the vehicle:
Not applying the parking brake when parking the vehicle is dangerous as the vehicle
may move unexpectedly and result in an accident. When parking the vehicle, shift
the selector lever to the P position and apply the parking brake.
When Driving
Brake
4-57
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

CAUTION
If you stop operating the accelerator pedal before the vehicle starts moving, the
force holding the vehicle in the stopped position may weaken. Firmly depress the
brake pedal or depress the accelerato r pedal to accelerate the vehicle.
NOTE
Under the following conditions, a problem with the AUTOHOLD is occurring.
Have your vehicle inspected at an Authorized Mazda Dealer as soon as possible.
A message is indicated on the multi-information display and a warning sound is
activated for about 5 seconds while the AUTOHOLD is operating or when you
press the AUTOHOLD switch.
If you switch the power switch OFF while the AUTOHOLD is operating, the
parking brake is applied automatically to assist you with parking the vehicle.
The AUTOHOLD is canceled when the selector lever is shifted to R position while
the vehicle is on level ground, or facing up a hill or grade (as shown below).
Vehicle posture and road surface gradient AUTOHOLD operation status
Ve h i c l e t i l t s f o r wa r d
Operates
Level ground
Does not operate, canceled
Ve h i c l e t i l t s rea r wa rd
Does not operate, canceled
: Reverse driving (selector lever in the reverse (R) position)
When Driving
Brake
4-58
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

NOTE
If the Electric Parking Brake (EPB)
switch is pulled while the
AUTOHOLD is operating, the
parking brake is applied and the
AUTOHOLD is released. In addition,
if the parking brake is released under
this condition, the AUTOHOLD
operates to hold the brakes.
Under the following conditions, the
parking brake is automatically
applied and the AUTOHOLD is
released. The AUTOHOLD is
re-enabled when the conditions
before the AUTOHOLD is released
are restored.
The driver’s seat belt is unfastened.The driver’s door is opened.When about 10 minutes or longer
have passed since the AUTOHOLD
operation started, the parking brake
is automatically applied. Because the
AUTOHOLD is restored when
releasing the parking brake, the hold
on the brakes by AUTOHOLD
function resumes.
The AUTOHOLD can be canceled
forcibly by fully depressing the
accelerator pedal for 1 second or
longer while the AUTOHOLD is
operating. Forcibly cancel the
AUTOHOLD only when the
AUTOHOLD cannot be canceled due
to a system malfunction or it is
necessary to cancel the AUTOHOLD
in an emergency.
▼To Tu r n
Off AUTOHOLD System
Depress the brake pedal and press the
AUTOHOLD switch. The AUTOHOLD
is turned o
ff and the AUTOHOLD
standby indicator light turns o ff.
1. AUTOHOLD standby indicator light
NOTE
When the brakes are not held such
as while driving the vehicle, the
AUTOHOLD can be turned o ff only
by pressing the AUTOHOLD switch.
If the AUTOHOLD switch is pressed
without depressing the brake pedal
while AUTOHOLD is operating
(AUTOHOLD active indicator light in
instrument cluster is turned on), the
message “Depress Brake Pedal and
Operate Switch to Release” is
indicated on the multi-information
display to notify the driver to depress
the brake pedal.
If any of the following conditions
occurs while the AUTOHOLD
function is operating (AUTOHOLD
active indicator light is turned on),
the parking brake is applied
automatically and the AUTOHOLD
function turns o ff. For the Electric
Parking Brake (EPB) operation, refer
to the Electric Parking Brake (EPB) on
page 4-52.
The power switch is switched OFF.There is a problem with the
AUTOHOLD function.
When Driving
Brake
4-60
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (white)
System stand-by status
If none of the systems are activated or
if there is a problem with the system,
the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (white) is displayed.
NOTE
For example, even when the Blind Spot
Monitoring (BSM) is operating
normally, if the Lane Departure
Warning System (LDWS) has a
problem, the i-ACTIVSENSE status
symbol (warning/risk avoidance
support system) (white) is displayed.
i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (green)
System activated status
If any one of the systems is activated,
the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (green) is displayed.
NOTE
Even if the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (green) is displayed, systems
which do not meet the operation
conditions will not operate.
i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (amber)
System warning status
If any system warning is activated, the
i-ACTIVSENSE status symbol (warning/
risk avoidance support system)
(amber) is displayed.
i-ACTIVSENSE OFF symbol (warning/
risk avoidance support system)
System OFF status
If all the systems are canceled using
[Settings] in Mazda Connect or the
i-ACTIVSENSE OFF switch, the
i-ACTIVSENSE OFF symbol (Warning/
risk avoidance support system) is
displayed.
▼ i-ACTIVSENSE OFF Switch*
When the i-ACTIVSENSE OFF switch is
pressed, the following systems are
canceled and the i-ACTIVSENSE OFF
symbol (Warning/risk avoidance
support system) in the instrument
cluster is displayed.
Lane Departure Warning System
(LDWS)
Blind Spot Monitoring (BSM)Distance & Speed Alert (DSA)Front Cross
Traffic Alert (FCTA)Rear Cross Tra
ffic Alert (RCTA)Lane-keep Assist System (LAS)
When Driving
i-ACTIVSENSE
4-70*Some models.
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

The front radar sensor includes a
function for detecting soiling of the
radar sensor's front surface and
informing the driver, however,
depending on the conditions, it may
require time to detect or it may not
detect plastic shopping bags, ice or
snow. If this occurs, the system may
not operate correctly, therefore
always keep the front radar sensor
clean.
 If “Safety and Driver Support Systems
Temporarily Disabled. Front Radar
Obscured. Drive Safely” is displayed
on the multi-information display of
the instrument cluster, clean the area
around the front radar sensor.
 Do not install a grille guard.
 If the front part of the vehicle has
been damaged in a vehicle accident,
the position of the front radar sensor
may have moved. Stop the system
immediately and always have the
vehicle inspected at an Authorized
Mazda Dealer.
 Do not use the front bumper to push
other vehicles or obstructions such
as when pulling out of a parking
space. Otherwise, the front radar
sensor could be hit and its position
deviated.
 For repairs, replacement or paint
work around the front radar sensor,
consult an Authorized Mazda Dealer.
 Always use tires for all wheels that
are of the speci fied size, and the
same manufacturer, brand, and tread
pattern. In addition, do not use tires
with signi ficantly di fferent wear
patterns on the same vehicle as the
system may not operate normally.
NOTE
If the lead-acid battery power is
weak, the system may not operate
correctly.
When driving on roads with little tra ffic and few vehicles ahead or
obstructions for the front radar
sensor to detect, “Safety and Driver
Support Systems Temporarily
Disabled. Front Radar Obscured.
Drive Safely” may be temporarily
displayed, however, this does not
indicate a problem.
The radar sensors are regulated by
the relevant radio wave laws of the
country in which the vehicle is
driven. If the vehicle is driven
abroad, authorization from the
country in which the vehicle is driven
may be required.
When the vehicle is driven on roads in
which there is an elevated road on one
side, the front radar sensor function
may be restricted temporarily.
When any of the following conditions
is met, the front radar sensor may not
be able to detect vehicles ahead or
obstructions correctly and each system
may not operate normally.
The rear surface of a vehicle ahead
does not re flect radio waves
e ff ectively (such as an unloaded
trailer, a vehicle with a loading
platform covered by a soft top, a
vehicle with a hard plastic liftgate,
and a round-shaped vehicle).
A vehicle ahead has limited areas
that can re flect radio waves (such as
a low pro file vehicle).
Under bad weather conditions (rain,
fog, and snow).
Front visibility is reduced (due to a
vehicle ahead casting o ff water,
snow, or sand).
Foreign matter (ice, snow, or dirt) is
on the surface of the front radar
sensor cover.
When Driving
i-ACTIVSENSE
4-76
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07