warning MERCEDES-BENZ C CLASS 2019 Owners Manual

Nevertouchthe danger zone surround‐ing moving component parts, e.g.therotation area ofthefan.
Removejewelry andwatches.
Keep items of clothing and hairawayfrom moving parts.
\nWARNINGRisk of injuryfromtouchingcomponent parts undervoltage
The ignition system andthe fuel injectionsystemworkunder highvoltage. Ifyoutouchcomponent parts which are undervoltage,you couldreceivean electric shock.
Nevertouch component parts oftheignition system orthe fuel injection sys‐tem whenthe ignition is switched on.
\nWARNINGRisk of burns from hot com‐ponent parts inthe engine compartment
Certain components inthe engine compart‐ment can beveryhot, e.g.the engine,theradiator and parts oftheexhaust system.
Allowthe enginetocool down and onlytouch component parts described inthefollowing.
\nWARNINGRisk of injuryfrom usingthewindshield wipers whilethe engine hoodis open
Whenthe engine hood is open andthe wind‐shield wipers are set in motion,you can betrappedbythe wiper linkage.
Always switch offthe windshield wipersand ignition before openingthe enginehood.
Toopen:pull lever1toreleasethe hood.
Maintenance and care353

Push handle1ofthe hood catch upwardsand liftthe hoodbyapproximately15in(40 cm).Toclose:lowerthe hood and let itfall from aheight of approximately 8 in (20 cm).
Ifthe hood canstill be lifted slightly,openthe hood again and close it with a little moreforce until it engages correctly.
Engine oil
Checkingthe engine oil level usingthe oildipstick
\nWARNINGRisk of burns from hot com‐ponent parts inthe engine compartment
Certain components inthe engine compart‐ment can beveryhot, e.g.the engine,theradiator and parts oftheexhaust system.
Allowthe enginetocool down and onlytouch component parts described inthefollowing.
Requirements:RThe engine must havean oil dipstick.If not,the engine oil level can bechecked only withthe on-board computer (page 355).
Depending onthe engine,the oil dipstick may beinstalled inthe engine compartment in differentlocations.
Thewaiting time beforecheckingthe oil levelwhenthe engine is at normal operatingtempera‐ture isfiveminutes.
Parkthevehicle on a level surface.
Pull oil dipstick1out and wipe off.
Slowly slide oil dipstick1intothe guidetubetothestop, andtakeit out again afterapproximatelythree seconds.ROil level is correct: oil level is between2and3.
ROil leveltoo low: oil level is at3orbelow.
354Maintenance and care

ROil leveltoo high: oil level is above2.
Ifthe oil level istoo low,add1.1 US qt(1 liter) of engine oil.
Ifthe oil level istoo high, drain offexcessengine oil. Consult aqualified specialistworkshop.
Checkingthe engine oil level usingthe on-board computer
RequirementsThe engine must havean oil level sensor. If not,the engine oil level can bechecked only withtheoil dipstick (page 354).
The engine oil level is determined during driving.Determiningthe engine oil level cantakeupto30 minutes with a normal drivingstyle andevenlonger with an active drivingstyle.
In ordertoreceivearesult asquickly as possi‐ble:
RWarmupthe engine
RParkthevehicle on a level surface
RLeavethe enginerunning at idling speed
On-board computer:
ServiceEngine Oil Level
You will see one ofthefollowing messages onthe multifunction display:
RMeasuring Engine Oil Level...: measurementofthe oil level is notyet possible.
Repeattherequest after a maximum of30 minutes driving.
REngine Oil Level OKandthe bar displayforindicatingthe oil level onthe multifunctiondisplay is green and is between "min" and"max":the oil level is correct.
REngine Oil Level Add 1.0 landthe bar displayfor indicatingthe oil level onthe multifunc‐tion display is orange and is below "min":
Add1.1 US qt (1 l) engine oil.
RReduce Engine Oil Levelandthe bar displayfor indicatingthe oil level onthe multifunc‐tion display is orange and is above"max":
Drain offexcess engine oilthat has beenadded. Consult aqualified specialistwork‐shop.
RFor Engine Oil Level Switch Ignition On:
Switch onthe ignitiontocheckthe engine oillevel.
REngine Oil Level System Inoperative: sensorfaulty or not inserted.
Consult aqualified specialistworkshop.
REngine Oil Level System Currently Unavail.:
Closethe hood.
Adding engine oil
\nWARNINGRisk of burns from hot com‐ponent parts inthe engine compartment
Certain components inthe engine compart‐ment can beveryhot, e.g.the engine,theradiator and parts oftheexhaust system.
Allowthe enginetocool down and onlytouch component parts described inthefollowing.
Maintenance and care355

\nWARNINGRisk offireand injury fromengine oil
If engine oil comes into contact withhotcomponent parts inthe engine compart‐ment, it may ignite.
Make surethat no engine oil is spillednexttothefiller opening.
Allowthe enginetocool off andthor‐oughly cleanthe engine oil from compo‐nent parts beforestartingthevehicle.
NOTEEngine damagecausedbyanincorrect oilfilter, incorrect oil or addi‐tives
Do not use engine oils or oilfilterswhich do not correspondtothe specifi‐cationsexplicitly prescribedfortheservice intervals.
Do not alterthe engine oil or oilfilter inordertoachievelongerchange intervalsthan prescribed.
Do not use additives.
Followthe instructions inthe serviceinterval displayregardingthe oilchange.
NOTEDamagecausedbyaddingtoomuch engine oil
Too much engine oil can damagethe engineorthe catalytic converter.
Haveexcess engine oilremoved at aqualified specialistworkshop.
Turncap1counter-clockwise andremoveit.
Add engine oil.
Replace cap1and turn it clockwise asfaras it will go.
Checkthe oil level again (page 354).
356Maintenance and care

Checking coolant level
\nWARNINGRisk of burns from hot com‐ponent parts inthe engine compartment
Certain components inthe engine compart‐ment can beveryhot, e.g.the engine,theradiator and parts oftheexhaust system.
Allowthe enginetocool down and onlytouch component parts described inthefollowing.
\nWARNINGDanger of burns when open‐ingthe hood
Ifyou openthe hood whenthe engine hasoverheated or during afireinthe enginecompartment,you could come into contactwith hotgases orother escaping operatingfluids.
Before openingthe hood, allowtheenginetocool down.
Intheevent of afireinthe engine com‐partment,keepthe hood closed andcallthefireservice.
\nWARNINGRisk of scalding from hotcoolant
The engine cooling system is pressurized,particularly whenthe engine iswarm. Ifyouopenthe cap,you could be scaldedbyhotcoolant spraying out.
Letthe engine cool down before open‐ingthe cap.
When openingthe cap,wear protectivegloves and safetyglasses.
Openthe cap slowlytorelease pres‐sure.
Parkthevehicle on a level surface.
Checkthe coolanttemperature display intheinstrument cluster.The coolanttemperature must be below158 °F (70 °C).
Slowly turn cap1counter-clockwisetorelieve overpressure.
Maintenance and care357

Continue turning cap1counter-clockwiseandremoveit.
The coolant level is correct:
RIfthe engine is cold, uptomarker bar2
RIfthe engine iswarm, upto0.6 in (1.5 cm)over marker bar2
If necessary,add coolantthat has beenapprovedbyMercedes-Benz.RFurther information on coolant(page 429).
Addingwasher fluidtothe windshieldwasher system
\nWARNINGRisk of burns from hot com‐ponent parts inthe engine compartment
Certain components inthe engine compart‐ment can beveryhot, e.g.the engine,theradiator and parts oftheexhaust system.
Allowthe enginetocool down and onlytouch component parts described inthefollowing.
\nWARNINGDanger of burns when open‐ingthe hood
Ifyou openthe hood whenthe engine hasoverheated or during afireinthe enginecompartment,you could come into contactwith hotgases orother escaping operatingfluids.
Before openingthe hood, allowtheenginetocool down.
Intheevent of afireinthe engine com‐partment,keepthe hood closed andcallthefireservice.
\nWARNING‑ Risk offireand injury fromwindshieldwasher concentrate
Windshieldwasher concentrate is highlyflammable. It could ignite if it comes intocontact withhot engine component parts ortheexhaust system.
Make surethat no windshieldwasherconcentrate spills out nexttothefilleropening.
Removecap1bythetab.
Addwasherfluid.
Keepingthe air-water duct free
Keepthe area betweenthe hood andthewindshield free of deposits, e.g. ice, snowand leaves.
358Maintenance and care

Cleaning and care
Information onwashingthevehicle in a carwash
\nWARNINGRisk of accident duetoreduced braking effect afterwashingthevehicle
The braking effect isreduced afterwashingthevehicle.
Afterthevehicle has beenwashed,brake carefully while paying attentiontothe traffic conditions untilthe brakingeffect has been fullyrestored.
NOTEDamageduetounsuitable carwash
Before driving into a carwash makesurethatthe carwash is suitableforthevehicle dimensions.
Ensurethere is sufficient ground clear‐ance betweenthe underbody andtheguiderails ofthe carwash.
Ensurethatthe clearance width ofthecarwash, in particularthe width oftheguiderails, is sufficient.
Toavoid damageto yourvehicle when using acarwash, ensurethefollowing beforehand:
RActive Distance AssistDISTRONIC andtheHOLD function are deactivated.
Rthe 360° Camera ortherear view camera isswitched off.
Rthe side windowsand sliding sunroof arecompletelyclosed.
Rthe blowerfortheventilation/heating isswitched off.
Rthe windshield wiper switch is in positionZ.
Rin carwashes with a conveyor system: neu‐tral\\is engaged.
Rthe SmartKeyis at a minimum distance of10ft(3 m)awayfromthevehicle,otherwisethe trunk lid could open unintentionally.
Ifyouwould liketoleavethevehicle while itis beingwashed, make surethe SmartKeyis
located inthevehicle. The]gear isother‐wise automatically engaged.
If, afterthe carwash,youremovethewaxfromthe windshield and wiperrubbers,thiswill prevent smearing andreduce wipernoise.
Information on using a powerwasher
\nWARNINGRisk of accident when usinghigh-pressure cleaning equipment withround-spraynozzles
Thewater jet from around-spraynozzle (dirtgrinder) may cause damagetotires and sus‐pension componentsthat is not visible.
Components damaged inthisway mayfailunexpectedly.
Do not use high-pressurecleaningequipment withround-spraynozzlestocleanyourvehicle.
Damaged tires or suspension compo‐nents must bereplaced immediately.
Maintenance and care359

Notes on care ofvehicle parts
\nWARNINGRisk of entrapment ifthewindshield wipers are switched on whilethe windshield is being cleaned
Ifthe windshield wipers are set in motionwhileyou are cleaningthe windshield orwiper blades,you can be trappedbythewiper arm.
Always switch offthe windshield wipersandthe ignition before cleaningthewindshield or wiper blades.
\nWARNINGRisk of burning fromthetail‐pipe ortailpipe trim
Thetailpipe andtailpipe trim can becomeveryhot. Ifyou come into contact withthesecar parts,you could burnyourself.
Always be particularlycareful when inthe vicinity ofthetailpipe andtailpipetrims and supervisechildrenveryclosely when inthis area.
Before any contact, allowthe car partstocool down.
Observethefollowing information:
Notes on cleaning and careAvoidingvehicle damage
Wheels/rimsUsewater and acid-free wheel cleaners.RDo not use acidic wheel cleanerstoremovebrake dust.This could damage wheel bolts and brake components.
RToavoid corrosion ofthe brake discs and brakepads, drivethevehiclefor afew minutes after cleaning before parkingit. The brake discs and brakepadswarmup and dry out.
WindowsClean windowsinside and outside with a damp clothand witha cleaning agentrecommendedfor Mercedes-Benz.Do not use dry cloths or abrasive or solvent-based cleaningagentstocleanthe inside of windows.
Wiper bladesFold outthe wiper blades and cleanthem using a damp cloth.Do not cleanthe wiper bladestoo often.
364Maintenance and care

Notes on cleaning and careAvoidingvehicle damage
Exterior lightingCleanthe lenses with awet sponge and mild cleaning agent,e.g. car shampoo.Only use cleaning agents or cleaning clothsthat are suitablefor plastic lenses.
SensorsCleanthe sensors inthe front andrear bumper and intheradiator grill with a soft clothand car shampoo.When using a powerwasher, maintain a minimum distance of11.8 in (30 cm).
Rear view cameraand360° CameraROpenthe camera cover withthe multimedia system(page 209) .
RUse cleanwater and a soft clothtocleanthe camera lens.
Do not use a powerwasher.
TailpipesClean with a cleaning agentrecommendedfor Mercedes-Benz, especiallyinthe winter and afterwashingthevehicle.Do not use acidic cleaning agents.
Notes on care ofthe interior
\nWARNINGRisk of injuryfrom plasticparts breaking off afterthe use of sol‐vent-based care products
Careand cleaning products containing sol‐vents can cause surfaces inthe cockpittobecome porous.
Whenthe airbags are deployed, plastic partsmay breakaway.
Do not use any care or cleaning prod‐ucts containing solventstocleanthecockpit.
\nWARNINGRisk of injuryor death frombleached seat belts
Bleaching or dyeing seat belts can severelyweakenthem.
This can,forexample, cause seat beltstotear orfail in an accident.
Never bleachor dye seat belts.
Maintenance and care365

Warning triangle
Removing thewarning triangle
Push bothsides ofwarning triangle holder1inthe direction ofthe arrowand open it.
Remove warning triangle2.
Setting upthewarning triangle
Fold sidereflectors1upwardstoforma tri‐angle and attach atthetop using upperpress-stud2.
Fold legs3down and outtothe side.
First-aid kit (soft-sided)overview
First-aid kit (softsided)1is inthe trunk intheleft-handstowage net.
Breakdown assistance369