MERCEDES-BENZ G55AMG 2007 W463 Owner's Manual

400 Practical hints
Jump starting
Make sure the two vehicles do not
touch.
Apply the parking brake (page 62).
Move the gear selector lever to park
positionP.
Turn off all electrical consumers.
Open the hood (page 267).The jump-start terminals are located on
the driver’s side of the engine compart-
ment.
1Cover
2Positive (+) terminal
3Negative (-) terminal Open cover1 of the positive terminal
of both vehicles.
Connect positive terminal2 and the
positive terminal of the charged battery
with the jumper cable. Clamp the cable
to the charged battery first.
Start the engine of the vehicle with the
charged battery and run at idle speed.
Connect negative terminal3 and the
negative terminal of the charged
battery with the jumper cable. Clamp
the cable to the charged battery first.
Start the engine of the disabled
vehicle.
You can now turn on the electrical con-
sumers. Do not switch on the headlamps
under any circumstances.
Remove the jumper cables first from
the negative terminals on each battery
and then from the positive terminals on
each battery.
You can now switch on the headlamps.
Have the battery checked at the
nearest authorized Mercedes-Benz
Light Truck Center.
Warning!G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(
page 396).
!Never invert the terminal connections!

401 Practical hints
Towing the vehicle
Towing the vehicle
Mercedes-Benz recommends that the
vehicle be transported with all wheels off
the ground using flatbed or appropriate
wheel lift/dolly equipment. This method is
preferable to other types of towing.When circumstances do not permit the
recommended towing methods, the
vehicle may be towed with all wheels on
the ground only so far as necessary to have
the vehicle moved to a safe location where
the recommended towing methods can be
employed.
!Use flatbed or wheel lift/dolly equipment,
with SmartKey in starter switch turned to
position0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
To prevent damage during transport, do not tie
down vehicle by its chassis or suspension parts.
Use the towing eyes.
Switch off the ESP
® (page 94), the tow-away
alarm (
page 98) and the automatic central
locking (
page 155).
!Do not tow-start the vehicle.
!When towing the vehicle with all wheels on
the ground, the gear selector lever must be in
neutral positionN and the SmartKey must be in
starter switch position2.
When towing the vehicle with all wheels on the
ground, the vehicle may be towed only for
distances up to 30 miles (50 km) and at a speed
not to exceed 30 mph (50 km/h).
If the vehicle is towed with one axle raised
(observe instructions regarding flexible drive
shaft and propeller shafts), the engine must be
shut off and the SmartKey must be in starter
switch position1. Otherwise, the 4-ETS may
become engaged which may cause loss of
towing control.
Warning!G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run

there is a malfunction in the brake sys-
tem

there is a malfunction in the power
supply or in the vehicle’s electrical
system
This is necessary to adequately control the
towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make sure the SmartKey is in
starter switch position2.
If the SmartKey is left in the starter switch
position0 for an extended period of time, it
can no longer be turned in the switch. In this
case, the steering is locked. To unlock,
remove SmartKey from starter switch and
reinsert.

402 Practical hints
Towing the vehicle
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle. Adapt your driving accordingly.
!Towing of the vehicle should only be done
using the towing eye. Never attach tow cable,
tow rope or tow rod to vehicle chassis, frame or
suspension parts.
iWhen towing the vehicle with all wheels on
the ground, note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, the
vehicle doors lock if a wheel is turning at vehicle
speeds of approximately 9 mph (15 km/h) or
above.
To prevent the vehicle doors from locking,
deactivate the automatic central locking
(
page 155).
iTo signal turns while being towed with
hazard warning flasher in use, turn the SmartKey
in starter switch to position2 and activate
combination switch for left or right turn signal in
usual manner – only the selected turn signal will
operate.
Upon canceling the turn signal, the hazard
warning flasher will operate again.
iThe gear selector lever will remain locked in
park positionP and the SmartKey will not turn in
the starter switch if the battery is disconnected
or discharged. For more information, see “Bat-
tery” (
page 396) and “Jump starting”
(
page 399).
For information on manually unlocking the gear
selector lever, see (
page 373).

403 Practical hints
Towing the vehicle
Transporting the vehicle
When transporting the vehicle, you can use
the towing eyes for pulling the vehicle onto
a trailer or transporter.
Move the gear selector lever to neutral
positionN.
Shift the transfer case to neutral
positionN.
To avoid damaging the vehicle, it
should only be tied down on the
wheels/wheel rims, not on chassis
components such as the transverse
link or trailing arm.Towing the vehicle - various problem
scenarios
Comply with all towing information
(
page 401).
In case of engine damage, transmission
damage or malfunctions in electrical
equipment
Move the gear selector lever to neutral
positionN.
Shift the transfer case to neutral
positionN.In case of transfer case damage or for
towing vehicle distances exceeding
30 miles (50 km)
The propeller shafts to the drive axles must
be removed.
In case of front axle damage
Raise the front axle when towing. The
propeller shaft between the rear axle and
the transfer case must be removed.
In case of rear axle damage
When the rear axle is raised, the vehicle
can only be towed with a wheel lift or a
dolly placed under its front wheels.
!When removing drive shaft, place M10 nuts
on bolts as distance sleeves and tighten
using M8 nuts.
Always install new self-locking nuts when
reinstalling the drive shaft.

404 Practical hints
Towing the vehicle
Front towing eye
The front towing eye is located on the
driver’s side under the front bumper.
1Towing eyeRear towing eye
The rear towing eye is located on the
driver’s side under the rear bumper.
1Towing eyeStranded vehicle
Freeing a stranded vehicle, on which the
wheels are dug into sand or mud, should
be done with the greatest of care,
especially if the vehicle is heavily loaded.
Avoid pulling the vehicle jerkily or diago-
nally, since it could result in damage to the
chassis alignment.
Never try to free a vehicle that is still
coupled to a trailer.
If possible, a vehicle should be pulled back-
ward in its own previously made tracks.

405 Practical hints
Fuses
Fuses
The electrical fuses in your vehicle serve to
switch off malfunctioning power circuits.
If a fuse is blown, the components and
systems secured by that fuse will stop
operating.If a newly inserted fuse blows again, have
the cause determined and rectified at an
authorized Mercedes-Benz Light Truck
Center.
The following aids are available to help you
replace fuses.

Fuse chart
The fuse chart explains the fuse
allocation and fuse amperages.
The fuse chart is located in the main
fuse box in the passenger compart-
ment (
page 406).

Spare fuses
The spare fuses are located in the main
fuse box in the passenger compart-
ment (
page 406).

Fuse extractor
The fuse extractor is located in the
vehicle tool kit in the rear footwell
(
page 366).The electrical fuses are located in different
fuse boxes:

in the passenger compartment on the
driver’s side (
page 406)

in the front passenger footwell
(
page 406)

in the middle tunnel (page 407)

in the battery box (page 408)
Before replacing fuses:
Apply parking brake (page 62).
Make sure the gear selector lever is set
to park positionP (
page 162).
Turn off all electrical consumers.
Turn off the engine (page 64).
Remove the SmartKey from the starter
switch.
Warning!G
Only use fuses approved by Mercedes-Benz
with the specified amperage for the system
in question and do not attempt to repair or
bridge a blown fuse. Using other than
approved fuses or using repaired or bridged
fuses may cause an overload leading to a
fire, and/or cause damage to electrical
components and/or systems. Have the
cause determined and remedied at an
authorized Mercedes-Benz Light Truck
Center.
iA blown fuse must be replaced by an
appropriate spare fuse (recognizable by its color
or the fuse rating given on the fuse) of the
amperage recommended in the fuse chart. Any
Mercedes-Light Truck Center will be glad to
advise you on this subject.

406 Practical hints
Fuses
Main fuse box in passenger compart-
ment
Open the driver’s door.
1Cover
Remove cover1 in direction of the
arrows.
Fuse box in front passenger footwell
Open the front passenger door.
1Mounting screw
2Cover
Unscrew mounting screws1.
Remove cover2 in direction of the
arrow.3Mounting screw
4Cover
Unscrew mounting screws3.
Remove cover4 in direction of the
arrows.
!Do not use sharp objects such as a screw
driver to open fuse box cover1 in the dash-
board, as this could damage it.
iWe recommend having the fuses changed at
a Mercedes-Benz Light Truck Center.

407 Practical hints
Fuses
5Fuse box
6Mounting screw
Unscrew mounting screws6.
Fold fuse box5 downward in direction
of the arrow.
Fuse box in middle tunnel
Removing front end stops
Open the front passenger door.
Front end stop on the right seat rail, left
seat rail laterally reversed
1Front end stop
2Spacing
Remove both front end stops1 of the
front passenger seat tracks using a
screwdriver.
Move front passenger seat fully
forward.
iTo make changing the fuses easier, fuse
box5 can be folded down slightly.
iWe recommend having the fuses changed at
a Mercedes-Benz Light Truck Center.
!When reinstalling front passenger seat track
stops, place end stops in correct position. For
your safety, maintain proper spacing2.
Warning!G
Do not drive the vehicle when the front end
stops are not correctly installed. Failure to
reinstall stops as indicated may result in
serious injury in certain frontal crashes.
Adjust the front passenger seat as far as
possible rearward from the dashboard when
the seat is occupied. Comply with informa-
tion on occupant safety (
page 68).

408 Practical hints
Fuses
Opening fuse box
Open the rear door on the passenger
side.
1Mounting screw
2Cover
Unscrew mounting screws1.
Remove cover2 in direction of the
arrow.
Fuse box in battery box
The battery box is located under a cover in
the rear footwell.
Replacement of fuses can only be
performed at a Mercedes-Benz Light Truck
Center.

409
Technical data
Parts service
Warranty coverage
Identification labels
Layout of poly-V-belt drive
Engine
Rims and tires
Electrical system
Main dimensions, vehicle weights
and ratings
Fuels, coolants, lubricants, etc.