exterior MITSUBISHI LANCER 2005 User Guide

MOULDINGS
EXTERIOR51-10
MOULDINGS
REMOVAL AND INSTALLATIONM1511004700295
AC304339 Y0622AU
Y0624AUY0623AU
Y0729AU
W0740AU
Section A – A
<Sedan>Section B – B Section C – C Section D – D
Section E – E
AB
N
N
N
N
N
C
C
EE
DD
B
B
A
A
1
2
6
4
3
5
7
8
9
N
N
N
111
98
51
1
6, 7
2, 3, 4

MOULDINGS
EXTERIOR51-11
REMOVAL SERVICE POINT
<<A>> ROOF DRIP MOULDING REMOVAL
CAUTION
If the moulding has become warped, it should not
be reused.
Use special tool window moulding remover
(MB990449) to lever out the moulding.
AC304340
1
1
A
A
A
A
AB
B
B
C
C
C
C
B
B
N
N
N
2
N2
4
3
N3
N4
N
6
9
7
N
6N
N
7N
N9
<Wagon>
<Vehicle with roof rail> <Vehicle without roof rail>
Removal
•Front deck garnishes (Refer to
P.51-23.)
Roof drip moulding removal steps
<<A>> >>C<<1. Roof drip moulding
>>B<<2. Front drip moulding clip A
>>B<<3. Front drip moulding clip B
>>B<<4. Front drip moulding clip C
>>B<<5. Rear drip moulding clip
>>A<<6. Drip moulding clip A
>>A<<7. Drip moulding clip B
>>A<<8. Drip moulding clip C
9. Roof drip moulding clip Roof drip moulding removal steps
AC304375MB990449AB

MOULDINGS
EXTERIOR51-12
INSTALLATION SERVICE POINTS
>>A<< DRIP MOULDING CLIP C/DRIP
MOULDING CLIP B/DRIP MOULDING
CLIP A INSTALLATION
1. The drip moulding clips A, B and C differ
according to where they are used, so check the
identification colour before installation.
2. After installing the clip to the front pillar outer in
alignment with its section A, cut from section B.
>>B<< REAR DRIP MOULDING
CLIP/FRONT DRIP MOULDING CLIP
C/FRONT DRIP MOULDING CLIP
B/FRONT DRIP MOULDING CLIP A
INSTALLATION
The front drip moulding clips A, B, C and rear drip
moulding clip differ according to where they are
used, so check the identification colour before
installation.
>>C<< ROOF DRIP MOULDING
INSTALLATION
Install the clips to the roof drip moulding before
installing the moulding to the vehicle body. Applicable location Identification colour
Drip moulding clip A Yellow
Drip moulding clip B Blue
Drip moulding clip C Milky white
AC304374
Front pillar outer
Section B
Section A
AB
Applicable location Identification colour
Front drip moulding clip A Orange
Front drip moulding clip B Purple
Front drip moulding clip C Blue
Rear drip moulding clip Grey

MOULDINGS
EXTERIOR51-13
AC401196 AC400117
AC400128
Section A – A Section B – B Section C – C
AB
A
AB
BC
C
2
1
3
ClipClip
AC400840AD
Double-sided tape: Generic products [ a: 6 mm width and 1.2 mm thickness,
b: 20 mm width and 1.2 mm thickness ]
12
3
a
b baAdhesive tape position
Door moulding removal steps
<<A>> >>A<<1. Front fender mouldingDoor moulding removal steps<<A>> >>A<<2. Front door moulding
<<A>> >>A<<3. Rear door moulding

MOULDINGS
EXTERIOR51-14
REMOVAL SERVICE POINT
<<A>> FRONT FENDER, FRONT AND
REAR DOOR MOULDINGS REMOVAL
Gently lift and remove the door moulding. If there is
any double-sided tape remaining on the door
moulding, remove according to the following
instructions.
<Remove double-sided tape remaining on the body
surface>
1. Attach protection tape all the way along the edges
of the double-sided tape which is still adhering to
the body.
2. Use a resin spatula to scrape off the double-sided
tape.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag
moistened with isopropyl alcohol.
<Remove double-sided tape remaining on door
moulding and adhere double-sided tape (when
re-using door moulding)>1. Scrape off the double-sided tape on the door
moulding with a resin spatula as possible.
2. Wipe the door moulding surface and clean it with
a rag moistened with isopropyl alcohol.
3. Remove only a small portion of the residual
adhesive.
4. Adhere the double-sided tape as specified on the
door moulding.
INSTALLATION SERVICE POINT
>>A<< FRONT FENDER, FRONT AND
REAR DOOR MOULDINGS
INSTALLATION
1. Tear off the double-sided tape backing paper.
NOTE: If attach the adhesive tape to the edge of
the backing paper, it will be easy to tear off.
2. Install the clips to the front and rear door
mouldings before installing them to the vehicle
body.
3. Install the door mouldings.
NOTE: . If the double-sided tape is difficult to affix
in cold temperature, etc., warm the bonding
surfaces of the body and door mouldings to about
40
− 60°C before affixing the tape.
4. Firmly press in the door mouldings onto the
respective body surfaces.
AC000420Double-sided tapeProtection tapeAB
AC000421
Double-sided tape
AB
AC313343
AC313344
Backing paper Adhesive tape
AB

SIDE AIR DAM
EXTERIOR51-15
SIDE AIR DAM
ADHESIVEM1511000500437
SIDE AIR DAM
REMOVAL AND INSTALLATIONM1511005500238
Item Specification
Side air dam Double-sided tape
4 mm width and 1.2 mm thickness
AC303877
Clip
Clip Section A – A
AD
1
A A
Adhesive tape position
Double-sided tape:
Generic products [ 4 mm width and 1.2 mm thickness ]11
Removal step
<<A>> >>A<<1. Side air dam

SIDE AIR DAM
EXTERIOR51-16
REMOVAL SERVICE POINTS
<<A>> SIDE AIR DAM REMOVAL
Gently lift and remove the side air dam. If there is
any double-sided tape remaining on the side air dam,
remove according to the following instructions.
<Remove double-sided tape remaining on the body
surface>
1. Attach protection tape all the way along the edges
of the double-sided tape which is still adhering to
the body.
2. Scrape off the double-sided tape with a resin
spatula as possible.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag
moistened with isopropyl alcohol.
<Remove double-sided tape remaining on the side
air dam and adhere double-sided tape(when re-using
side air dam)>1. Scrape off the double-sided tape on the side air
dam with a resin spatula as possible.
2. Wipe the side sill garnish surface and clean it with
a rag moistened with isopropyl alcohol.
3. Remove only a small portion of the residual
adhesive.
4. Adhere the double-sided tape as specified on the
side air dam.
INSTALLATION SERVICE POINT
>>A<< SIDE AIR DAM INSTALLATION.
1. Tear off the double-sided tape backing paper.
NOTE: If you attach the adhesive tape to the edge
of the backing paper, it will be easy to tear off.
2. Install the side air dam.
NOTE: If the double-sided tape is difficult to affix
in cold temperature, etc., warm the bonding
surfaces of the body and side air dam to about 40
− 60°C before affixing the tape.
3. Firmly press in the side air dam.
AC304143AB
Protection tape
Double-sided tape
AC304144AB
Double-sided tape
AC304145
AC304146
Backing paper
Adhesive tape
AB

GARNISHES
EXTERIOR51-17
GARNISHES
REMOVAL AND INSTALLATIONM1511004100107
AC303863
Clip
Delta outer garnishSection A – A
AB
Delta outer
garnish
A A
AC303860
A A
Clip Trunk lid panel
Licence plate
garnish Section A – A
AB
Licence plate garnish
<Sedan>

REAR SPOILER
EXTERIOR51-18
REAR SPOILER
REMOVAL AND INSTALLATIONM1511006100136
REMOVAL SERVICE POINT
<<A>> HIGH-MOUNTED STOP LAMP
REMOVAL
Use the following steps to easily route high-mounted
stop lamp harness in the event of installation:
CAUTION
Ensure that the string is tightly tied.
1. Tie string on high-mounted stop lamp harness (at
connector side).
2. Carefully pull out high-mounted stop lamp.
AC303713
2 3
4
2
1
AB
1
Removal steps
•Trunk lid bumper (Refer to GROUP
42, Trunk lid P.42-43.)
1. Cap2. Gasket
3. Rear spoiler
<<A>>4. High-mounted stop lampRemoval steps (Continued)
AC303708
Connector String
AB

TAILGATE SPOILER
EXTERIOR51-19
TAILGATE SPOILER
REMOVAL AND INSTALLATIONM1511019900068
AC303721
1
2 3
AB
5.2 ± 1.0 N·m
Tailgate spoiler removal steps
•Tailgate trim upper (Refer to GROUP
52A, Tailgate trim P.52A-19.)
•High-mounted stoplight connector
connection•Rear washer hose connection
1. Tailgate spoiler assembly
2. High-mounted stoplight assembly
3. Tailgate spoiler Tailgate spoiler removal steps