stop start MITSUBISHI LANCER 2005 User Guide

WINDOW GLASS
BODY42-17
REMOVAL SERVICE POINTS
<<A>> REAR WINDOW LOWER
MOULDING REMOVAL
CAUTION
If the drip moulding has become warped, it
should not be reused.
Use special tool ornament remover (MB990784) to
lever out the moulding.
<<B>> REAR WINDOW GLASS REMOVAL
Removal the rear window glass using the same
procedure as for the windshield. (Refer to P.42-12.)
INSTALLATION SERVICE POINTS
>>A<< GLASS STOPPER/WINDOW
DAM/REAR WINDOW UPPER
MOULDING/REAR WINDOW GLASS
INSTALLATION
1. When replacing the rear window glass,
temporarily set the rear window glass against the
body, and place a mating mark on the rear
window glass and body.
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
2. Use isopropyl alcohol to degrease the inside and
outside of the rear window glass and the body
flanges.
CAUTION
•The primer strengthens the adhesive, so be
sure to apply it evenly around the entire
circumference. However, a too thick
application will weaken the adhesive.
•Do not touch the coated surface.
3. Soak a sponge in the primer, and apply evenly to
the rear window glass and the body in the
specified places.
4. Allow the rear window glass to dry for at least 3
minutes after applying primer.
>>A<<9. Window dam
>>A<<10. Glass stopperRemoval steps (Continued)
AC006073
AB
MB990784

WINDOW GLASS
BODY42-23
REMOVAL SERVICE POINT
<<A>> TAILGATE WINDOW GLASS
REMOVAL
Remove the tailgate window glass using the same
procedure as for the windshield (Refer to P.42-12).
INSTALLATION SERVICE POINTS
>>A<< WINDOW SPACER/GLASS
STOPPER/DUAL LOCK
FASTENER/WINDOW DAM
INSTALLATION
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
1. Use isopropyl alcohol to degrease the inside and
outside edges of the tailgate window glass and
the surface of the tailgate flange.
Removal steps
1. Connecting the harness connector
<<A>> >>B<<2. Tailgate window glass
>>A<<3. Window lower dam
>>A<<4. Window side dam
>>A<<5. Dual lock fastener
>>A<<6. Glass stopper
>>A<<7. Window spacerRemoval steps (Continued)

IGNITION SWITCH
CHASSIS ELECTRICAL54A-20
ON-VEHICLE SERVICE
HOW TO REGISTER ENCRYPTED CODEM1543008100410
CAUTION
Because registering the encrypted codes is done
after all previously-registered codes have been
erased, you should keep all of the ignition keys
that have already been registered accessible.
If the ignition key, Immobilizer-ECU,
engine-ECU<M/T> or engine-A/T-ECU<A/T> is
replaced or an ignition key is added, encrypted
codes of all the ignition keys must be registered. (A
maximum of eight different ignition key can be
registered.) Moreover, when the immobilizer-ECU
has been replaced, you will need to use MUT-II/III to
register the immobilizer-ECU and input the vehicle
secret code and to register the password (secret
code) that the owner specifies into the
immobilizer-ECU.
If an attempt is made to start the engine with an
unregistered ignition key, cranking occurs, but fuel
supply is cut off to disable the engine. In
approximately.
NOTE: Engine-ECU<M/T> or engine-A/T-ECU<A/T>
has an encrypted code for immobilizer-ECU, and the
encrypted code is registered in the immobilizer-ECU
and ignition key.
POINTS TO NOTE DURING OPERATION
If none of the functions can be used, check the
diagnosis codes, and after carrying out any
necessary repairs, repeat the operation.
If an incorrect password is input ten times in a row,
the immobilizer-ECU judges that an unauthorized
operation is being attempted. Start-prevention mode
will be set, and engine operation will stop and all
special functions will be disabled. If the ignition
switch is turned to "ON" position, "Unauthorized
operation, start- prevention mode" will be cancelled.
KEY ID (ENCRYPTED CODE)
REGISTRATION <MUT-II>
All ignition keys can be registered with MUT-II.
Additional ignition keys can be registered with
MUT-II.
Registration with the MUT-II
CAUTION
To prevent damage to MUT-II, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting MUT-II.
NOTE: .
•Using the key ID register function will cause all
key IDs that have been previously registered in
the immobilizer-ECU to be erased. All keys need
to be registered. Those which have been
registered before should be on hand before using
this function.
•If registering more than one key, do not
disconnect MUT-II halfway through the
registration process.
•After registering key IDs, check that the engine
can be started using all of the keys that have
been registered. If the engine will not start, refer
to Immobilizer System Diagnosis P.54A-6.
1. Connect MUT-II to diagnosis connector (16- pin).
2. Turn the ignition switch to "ON" position.
3. At "System Select," press "YES"
AC304777
Steering shaft
AB
MB991502
<Using the MUT-II>
AC000522AD

POWER DISTRIBUTION SYSTEM <LHD>
CIRCUIT DIAGRAMS90-15
POWER DISTRIBUTION SYSTEM <LHD>
M1901000401106
·CENTRAL DOOR
LOCKING SYSTEM
·CLOCK
·FRONT FOG LAMP
·FUEL WARNING
LAMP
·HEADLAMP
·HEADLAMP
LEVELLING SYSTEM
·INVECS-II 4A/T
·KEY REMINDER
BUZZER
·METER AND GAUGE
·POWER WINDOWS
·REAR FOG LAMP
·REAR WIPER AND
WASHER
·ROOM LAMP AND
LUGGAGE COM-
PARTMENT LAMP
·ROOM LAMP,
PERSONAL LAMP
AND LUGGAGE
ROOM LAMP
·SPARE CONNECTOR
(FOR AUDIO)
·TAIL LAMP, POSITION
LAMP, LICENCE PLATE
LAMP AND LIGHTING
MONITOR BUZZER
·TURN-SIGNAL LAMP
AND HAZARD
WARNING LAMP
·WINDSHIELD WIPER
AND WASHERENGINE
CONTROL
SYSTEM
INVECS-II
4A/TTURN-SIGNAL
LAMP AND
HAZARD
WARNING LAMP
CHARGING
SYSTEMACCESSORY
SOCKET
·ABS
·INVECS-II
4A/T
·STOP LAMP·HEATER
·MANUAL AIR
CONDITIONER
·COOLING
SYSTEM
·ENGINE
CONTROL
SYSTEM
·IGNITION SYSTEM
·IMMOBILIZER
SYSTEM
·INVECS-II 4A/THORN ·COOLING
SYSTEM
·MANUAL AIR
CONDITIONERABS
POWER
WINDOWS CHARGING
SYSTEMSTARTING
SYSTEM
BATTERY
RELAY
BOX FUSIBLE
LINK
·REAR WINDOW
DEFOGGER AND DOOR
MIRROR HEATER
·RHEOSTAT
·SPARE CONNECTOR
(FOR AUDIO)
·TAIL LAMP, POSITION
LAMP, LICENCE PLATE
LAMP AND LIGHTING
MONITOR BUZZER
·TURN-SIGNAL LAMP AND
HAZARD WARNING LAMP ·CIGARETTE LIGHTER
AND ASHTRAY
ILLUMINATION LAMP
·FRONT FOG LAMP
·HEATER
·HEADLAMP
LEVELLING SYSTEM
·INVECS-II 4A/T
·MANUAL AIR
CONDITIONER
·METER AND GAUGE
·REAR FOG LAMP HEADLAMP
LEVELLING
SYSTEMHEADLAMP
HEADLAMP ·FRONT FOG
LAMP
·SPARE
CONNECTOR
(FOR FRONT
FOG LAMP)
FRONT-ECU
HEADLAMP
RELAY: LOHEADLAMP
RELAY: HITAIL LAMP
RELAY
·HEADLAMP
·HEADLAMP
LEVELLING
SYSTEMTAIL LAMP, POSITION
LAMP, LICENCE PLATE
LAMP AND LIGHTING
MONITOR BUZZER
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet
: 4G1
: 4G6 NOTE
HEATED
SEAT

POWER DISTRIBUTION SYSTEM <RHD>
CIRCUIT DIAGRAMS90-17
POWER DISTRIBUTION SYSTEM <RHD>
M1901000401117
·CENTRAL DOOR
LOCKING SYSTEM
·CLOCK
·FRONT FOG LAMP
·FUEL WARNING
LAMP
·HEADLAMP
·HEADLAMP
LEVELLING SYSTEM
·INVECS-II 4A/T
·KEY REMINDER
BUZZER
·METER AND GAUGE
·POWER WINDOWS
·REAR FOG LAMP
·REAR WIPER AND
WASHER
·ROOM LAMP AND
LUGGAGE COM-
PARTMENT LAMP·ROOM LAMP,
PERSONAL LAMP
AND LUGGAGE
ROOM LAMP
·SPARE CONNECTOR
(FOR AUDIO)
·TAIL LAMP, POSITION
LAMP, LICENCE PLATE
LAMP AND LIGHTING
MONITOR BUZZER
·TURN-SIGNAL LAMP
AND HAZARD
WARNING LAMP
·WINDSHIELD WIPER
AND WASHERENGINE
CONTROL
SYSTEM
INVECS-II
4A/TTURN-SIGNAL
LAMP AND
HAZARD
WARNING LAMP
CHARGING
SYSTEMACCESSORY
SOCKET
·ABS
·INVECS-II
4A/T
·STOP LAMP·HEATER
·MANUAL AIR
CONDITIONER
·COOLING
SYSTEM
·ENGINE
CONTROL
SYSTEM
·IGNITION SYSTEM
·IMMOBILIZER
SYSTEM
·INVECS-II 4A/THORN ·COOLING
SYSTEM
·MANUAL AIR
CONDITIONERABS
POWER
WINDOWS STARTING
SYSTEM
BATTERY
RELAY
BOX FUSIBLE
LINK
RELAY
BOX
·REAR WINDOW
DEFOGGER AND DOOR
MIRROR HEATER
·RHEOSTAT
·SPARE CONNECTOR
(FOR AUDIO)
·TAIL LAMP, POSITION
LAMP, LICENCE PLATE
LAMP AND LIGHTING
MONITOR BUZZER
·TURN-SIGNAL LAMP AND
HAZARD WARNING LAMP ·CIGARETTE LIGHTER
AND ASHTRAY
ILLUMINATION LAMP
·FRONT FOG LAMP
·HEATER
·HEADLAMP
LEVELLING SYSTEM
·INVECS-II 4A/T
·MANUAL AIR
CONDITIONER
·METER AND GAUGE
·REAR FOG LAMP HEADLAMP
LEVELLING
SYSTEMHEADLAMP
HEADLAMP ·FRONT FOG
LAMP
·SPARE
CONNECTOR
(FOR FRONT
FOG LAMP)
FRONT-ECU
HEADLAMP
RELAY: LOHEADLAMP
RELAY: HITAIL LAMP
RELAY
·HEADLAMP
·HEADLAMP
LEVELLING
SYSTEMTAIL LAMP, POSITION
LAMP, LICENCE PLATE
LAMP AND LIGHTING
MONITOR BUZZER
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet
: 4G1
: 4G6 NOTE
CHARGING
SYSTEM