ABS MITSUBISHI LANCER EVOLUTION IV 1998 Owner's Manual

REAR SUSPENSION – Lower Arm and Toe Control Arm AssembliesREAR SUSPENSION – Lower Arm and Toe Control Arm Assemblies34-10
LOWER ARM AND TOE CONTROL ARM ASSEMBLIES
REMOVAL AND INSTALLATION
Post-installation Operation
(1) Check the Toe Control Arm Ball Joint Dust Cover
for Cracks or Damage by Pushing it with Finger(2) Wheel Alignment Check and Adjustment
(Refer to P.34-3.)
12
3 4 5
6
Unit: Nm {kgf
m}
93 {9.5}*
88 {9.0}* 74 – 87 {7.5 – 8.9}*
88 {9.0}*93 {9.5}*
2
Lower arm assembly removal steps
1. Lower arm assembly and shock
absorber connecting bolt
A2. Lower arm assembly mounting bolt
A3. Lower arm assemblyToe control arm assembly removal
steps
B4. Toe control arm and knuckle
connection
C5. Toe control arm assembly mounting
bolt
6. Toe control arm assembly
Caution
The part marked with * should be first temporarily
tightened, then torqued to specification with the
vehicle on the ground in unloaded condition.
REMOVAL SERVICE POINTS
ALOWER ARM ASSEMBLY MOUNTING BOLT
REMOVAL
Place mating marks on the lower arm and the eccentric cam
bolt before removal.Mating marks

REAR SUSPENSION – Shock Absorber Assembly34-13
SHOCK ABSORBER ASSEMBLY
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Trunk Room Side Trim Removal and Installation
<GSR>
1
2
34
Unit: Nm {kgf
m}
44 {4.5}
88 {9.0}*
Removal steps
1. Cap
2. Shock absorber mounting nuts
3. Bolt
4. Shock absorber assemblyCaution
The part marked with * should be first temporarily
tightened, then torqued to specification with the
vehicle on the ground in unloaded condition.

BASIC BRAKE SYSTEM 35A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANTI-LOCK BRAKING SYSTEM (ABS) 35B. . . . . . . . . . . . . . . . . . . . . .
35-1
SERVICE BRAKES
CONTENTS

35B-1
ANTI-LOCK
BRAKING
SYSTEM (ABS)
CONTENTS
TROUBLESHOOTING 2. . . . . . . . . . . . . . . . . . . .
1. Inspection Chart for Diagnosis Codes 2. . .
2. Inspection Procedure for Diagnostic
Trouble Codes 3. . . . . . . . . . . . . . . . . . . . . . . .
3. Inspection Chart for Trouble Symptoms 11
4. Inspection Procedure for Trouble
Symptoms 12. . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Check at ABS-ECU Terminals 15. . . . . . . . .
ON-VEHICLE SERVICE 17. . . . . . . . . . . . . . . .
Wheel Speed Sensor Output Voltage
Measurement <EVOLUTION-V> 17. . . . . . . . . . .
LATERAL ACCELERATION SENSOR 17. . .
WHEEL SPEED SENSOR 18. . . . . . . . . . . . . .

ABS – Troubleshooting35B-2
The EVOLUTION-V is provided with a lateral acceleration sensor in addition to the longitudinal acceleration
sensor, and the ABS-ECU connector is changed in terminal arrangement. When servicing EVOLUTION-V,
therefore, use the following service procedures.
TROUBLESHOOTING
1. INSPECTION CHART FOR DIAGNOSIS CODES
Diagnosis
code No.Diagnosis itemsReference Page
11Wheel speed sensor (FR) system (open- or short-circuit)35B-3
12Wheel speed sensor (FL) system (open- or short-circuit)35B-3
13Wheel speed sensor (RR) system (open- or short-circuit)35B-3
14Wheel speed sensor (RL) system (open- or short-circuit)35B-3
15Wheel speed sensor system (abnormal output signal)35B-4
16ABS-ECU power supply voltage system (abnormal voltage drop or rise)35B-5
21Wheel speed sensor (FR) system35B-2
22Wheel speed sensor (FL) system35B-2
23Wheel speed sensor (RR) system35B-2
24Wheel speed sensor (RL) system35B-2
27AYC monitor system (detective AYC)35B-6
32Longitudinal acceleration sensor circuit system35B-6
33Stop lamp switch system35B-7
41Solenoid valve (FR) system35B-7
42Solenoid valve (FL) system35B-7
43Solenoid valve (RR) system35B-7
44Solenoid valve (RL) system35B-7
51Valve relay system35B-8
53Motor relay system35B-9
63ABS-ECU failureReplace ABS-ECU.
71Lateral acceleration sensor system35B-10

ABS – Troubleshooting35B-3
2. INSPECTION PROCEDURE FOR DIAGNOSTIC TROUBLE CODES
Code Nos.11, 12, 13 and 14: Wheel speed sensor
(open circuit or short circuit)Probable cause
Code Nos.21, 22, 23 and 24: Wheel speed sensor
Code Nos 11, 12, 13 and 14 are output if the ABS-ECU detects an open circuit or
short-circuit in the (+) wire or (–) wire in any one of the four wheel speed sensors.
Malfunction of wheel speed sensor

Malfunction of wiring harness or connector

Malfunction of ABS-ECU
Code Nos.21, 22, 23 and 24 are output in the following cases.

When there is no input from any one of the four wheel speed sensors when travelling
at 8 km/h or more, even though open circuit can not be verified.

When a chipped or blocked-up ABS rotor is detected and if the anti-lock system
operates continuously because a malfunctioning sensor or a warped ABS rotor
is causing sensor output to drop.
Malfunction of wheel speed sensor

Malfunction of wiring harness or connector

Too much gap between the sensor and the rotor

Malfunction of ABS-ECU

Malfunction of wheel bearing
NG
Check the harness wire, and repair
if necessary.

Between each wheel speed sensor
and ABS-ECU
NG
Replace the ABS-ECU.
OK
Check the trouble symptom.
OK
Check the following connector:
B-24NG
Repair
NG
Repair
OK
Wheel bearing check
OK
ABS rotor check
OK
Wheel speed sensor output voltage
check (Refer to P.35B-17.)NGWheel speed sensor checkNG
Replace
OK
Check the following connectors:
B-24, B-52, B-17, A-26, A-50, D-04,
D-14, D-19OKCheck the trouble symptom.
OK
Measure at the ABS-ECU connector
B-24.

Disconnect the connector, and
measure at the harness side
connector.

Resistances between 8 and 21,
10 and 19, 7 and 20, 9 and 22
OK:1.4 – 1.8 kΩNGWheel speed sensor check
(Refer to P.35B-29.)NG
Replace
Wheel speed sensor installation checkNG
Replace
NG
Replace

ABS – Troubleshooting35B-4
Code No.15: Wheel speed sensor (abnormal output
signal)Probable cause
This code is output when there is an abnormality in the output signal from any one
of the four wheel speed sensors while driving (except for an open circuit or short
circuit).
The four vehicle tires are of different sizes

Malfunction of wheel speed sensor

Malfunction of wiring harness or connector

Malfunction of ABS-ECU

Malfunction of wheel bearing
OK
Check the harness wire, and repair
if necessary.

Between each wheel speed sensor
and ABS-ECU
OK
Wheel bearing checkNG
Replace the ABS-ECU.
OK
ABS rotor checkNG
RepairOK
Check the trouble symptom.
OK
Check the following connector:
B-24NG
Repair
OK
Check the trouble symptom.
OK
Wheel speed sensor output voltage
check (Refer to P.35B-17.)NGWheel speed sensor checkNG
Replace
YES
Wheel speed sensor installation checkNG
Repair
Are the sizes of all four tires identical?NOEquip the vehicle with tires of identical
sizes.
NG

ABS – Troubleshooting35B-5
Code No.16: ABS-ECU power supply system (abnormal
voltage drop or rise)Probable cause
This code is output if the ABS-ECU or valve relay power supply voltage drops below
or rises above the rated values.
The valve relay power supply voltage is detected based on the voltage in the valve
relay monitor line.
Malfunction of battery

Malfunction of wiring harness or connector

Malfunction of valve relay

Malfunction of ABS-ECU
Caution
If battery voltage drops or rises during inspection, this code will be output as well, making it
impossible to obtain correct diagnostic results.
Before carrying out the following inspection, check the battery level, and refill it if necessary.
OK
Replace ABS-ECU.
OK
Replace the ABS-ECU.
OK
Check the trouble symptom.NGCheck the harness wire, and repair
if necessary.

Between ignition switch and
ABS-ECU
OK
Check the trouble symptom.NGCheck the harness wire, and repair
if necessary.

Between general-purpose fuse
No. 6 and valve relay
NG
Repair
OK
Check the harness wire for short
circuit, and repair if necessary.

Between valve relay and hydraulic
unit

Between valve relay and motor
relayNG
Repair OK
NG
Check the harness wire, and repair
if necessary.

Between valve relay and ABS-ECUNG
Repair
OK
Check the trouble symptom.
OK
Check the trouble symptom.NGCheck the harness wire, and repair
if necessary.

Between general-purpose fuse
No. 6 and valve relay
OK
Measure at the ABS-ECU connector
B-25.

Connector connected

Ignition switch: ON
(1) Voltage between 37 and body
ground
OK:Battery voltage
(2) Voltage between 48 and body
ground
OK:Battery voltage(1) NGCheck the following connectors:
A-76, B-25NG
Repair
(2) NG
Check the following connectors:
A-76, B-25NG
Repair
OK
Check the valve relay.NG
Replace
OK
Check the trouble symptom.NGCheck the harness wire, and repair
if necessary.

Between fusible link No. 8 and
valve relay
OK
Measure at the valve relay connector
A-76.

Disconnect the connector, and
measure at the harness side
connector.

Ignition switch: ON
(1) Voltage between 6 and body
ground
OK:Battery voltage
(2) Voltage between 2 and body
ground
OK:Battery voltage(1) NGCheck the following connector:
A-76NG
Repair
(2) NGCheck the following connector:
A-76NG
Repair
Measure at the ABS-ECU connector
B-24.

Disconnect the connector, and
measure at the harness side
connector.

Start the engine.

Voltage between 13 and body
ground
OK:Battery voltageNGCheck the following connectors:
B-24, B-52, B-74, B-76NG
Repair

ABS – TroubleshootingABS – Troubleshooting35B-6
Code No. 27: AYC monitor system (defective AYC)Probable cause
This code is output when the AYC monitor signal becomes faulty.
Defective AYC-ECU

Defective ABS-ECU

Defective harness or connector
OK
Replace the ABS-ECU.
OK
MUT-II data list
AYC signal
OKOFF to be displayed when the
engine runs at idle with the
vehicle stationary.NGReplace AYC-ECU.
OK
Check the harness between ABS-ECU
and AYC-ECU.NG
Repair
Check the following connectors:
B-25, B-96NG
Repair
Code No. 32: Acceleration sensor (longitudinal accelera-
tion) circuit systemProbable cause
This code is output under either of the following conditions:

The output from the acceleration sensor (longitudinal acceleration) becomes 0.5
V or less, or 4.5 V or more.

The acceleration sensor (longitudinal acceleration) harness is open- or
short-circuited.
Defective acceleration sensor (longitudinal accelera-
tion)

Defective harness or connector

Defective ABS-ECU
OK
Check the trouble symptom.NGReplace ABS-ECU.
OK
Check the trouble symptom.NGCheck and repair the harness between
acceleration sensor (longitudinal
acceleration) and ABS-ECU.
OK
Check the trouble symptom.NGCheck and repair the harness between
general-purpose fuse No. 6 and
acceleration sensor (longitudinal
acceleration).
OK
Replace ABS-ECU.
OK
Check the following connector:
B-24NG
Repair
OK
Measure at B-24 ABS-ECU connector.

Connect the connector.

Ignition switch: ON

Voltage across 4 and 17
OK:2.4 – 2.6 V
(horizontal position)NGCheck the following connectors:
B-24, D-20, B-52NG
Repair
NG
Check the harness between accelera-
tion sensor (longitudinal acceleration)
and ABS-ECU.NG
Repair
OK
Check the trouble symptom.
OK
Check the valve relay.NG
Replace
(1) NGCheck the following connectors:
D-20, B-49, B-75NG
Repair
Check the following connector:
D-20, B-49, B-75NG
Repair
(2) NG
Measure at D-20 acceleration sensor
(longitudinal acceleration) connector.

Disconnect the connector and
measure at the harness side.

Ignition switch: ON
(1) Voltage across 1 and body ground
OK:Battery voltage
(2) Continuity across 3 and body
ground
OK:Conducting

ABS – Troubleshooting35B-7
Code No.33: Stop lamp switch system (open circuit or
stop lamp stays ON)Probable cause
This code is output, if the stop lamp switch is continuously on for 15 minutes or
more.
Malfunction of stop lamp switch

Malfunction of wiring harness or connector

Malfunction of ABS-ECU
OK
Check the trouble symptom.NGCheck the harness wire, and repair
if necessary.

Between dedicated fuse No. 11
and ABS-ECU
OK
Check the trouble symptom.NGReplace the ABS-ECU.
OK
Check the trouble symptom.NGCheck the harness wire, and repair
if necessary.

Between stop lamp switch and
ABS-ECU
OK
Check the following connectors:
B-15, B-21, B-25, B-32, B-65NG
Repair
OK
Check the following connector:
B-25NG
Repair
YES
Measure at the ABS-ECU connector
B-25.

Disconnect the connector, and
measure at the harness side
connector.

Stop lamp switch: ON

Voltage between 34 and body
ground
OK:Battery voltageNG
Check the following connectors:
B-25, B-32, B-65NG
Repair
OK
Stop lamp switch checkNG
Repair
Does the stop lamp turn on and off
normally?NOStop lamp switch installation checkNG
Repair
Code No. 41, 42, 43, 44: Solenoid valve systemProbable cause
ABS-ECU monitors the solenoid valve energization circuit at all times. This code is
output when no current flows through the solenoid even when ABS-ECU energizes
it or when current continues flowing through the solenoid even when ABS-ECU
deenergizes it, which is considered to be attributable to an open- or short-circuited
solenoid coil or open- or short-circuited harness.
Defective hydraulic unit

Defective harness or connector

Defective ABS-ECU
OK
Replace the ABS-ECU.
OK
Check the trouble symptom.NGCheck the harness between hydraulic
unit (solenoid valve) and ABS-ECU.NG
Repair
OK
Check the trouble symptom.NGCheck and repair the harness between
hydraulic unit and valve relay.
OK
Check the following connectors:
A-21, B-24, B-25NG
Repair
OK
Measure at A-22 hydraulic unit connec-
tor and A-76 valve relay connector.

Disconnect the connector and
measure at the harness side.

Continuity across the following
terminals
Hydraulic Valve relay
unit side side
11–3
OK:Battery voltageNGCheck the following connectors:
A-22, A-76NG
Repair
Check the solenoid valve.NGReplace the hydraulic unit.