torque MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

ENGINE – Camshaft and Camshaft Oil Seal11-12
BCAM CAP / REAR CAP / FRONT CAM CAP
INSTALLATION
(1) Locate the camshaft dowel pins as illustrated.
(2) Temporarily tighten cam cap in two to three steps, then
torque it to specification.
Tightening torque: 20 Nm {2.0 kgf
m}
CCAMSHAFT OIL SEAL INSTALLATION
(1) Apply engine oil to the entire periphery of the oil seal
lip.
(2) Pressfit the oil seal as shown.
DCAMSHAFT SPROCKET INSTALLATION
As you did during removal, secure the camshaft sprocket
with the special tool and tighten bolt to specification.
Tightening torque: 88 Nm {9.0 kgf
m}
ECAM POSITION SENSING CYLINDER
Install the cam position sensing cylinder so that the ID paint
on the cam position sensing cylinder is 90
with respect to
the camshaft dowel pin as shown.
Intake side Approx. 12
Dowel pin
Exhaust side
MD998713
ID paintDowel pin
90

ENGINE – Crankshaft Oil Seal11-16
REMOVAL SERVICE POINT
AFLYWHEEL ASSEMBLY REMOVAL
Use the special tool to secure the flywheel assembly and
remove the bolts.
INSTALLATION SERVICE POINTS
ACRANKSHAFT REAR OIL SEAL INSTALLATION
(1) Apply a small mount of engine oil to the entire
circumference of the oil seal lip.
(2) Install the oil seal with the special tool as far as the
chamfered position of the oil seal case as shown in the
illustration.
BFLYWHEEL ASSEMBLY INSTALLATION
Use the special tool to hold the flywheel in the same manner
as removal, and install the bolt. Tighten the bolts to the
specification.
Tightening torque: 127 – 137 Nm {13.0 – 14.0 kgf
m}
CCRANKSHAFT FRONT OIL SEAL INSTALLATION
Apply a small amount of engine oil to the entire circumference
of the oil seal lip.
Pressfit the oil seal until it is flush with the chamfered end
of the oil pump case.
MD998781
Crankshaft
rear oil seal
MB990938
MB998776Crankshaft
Crankshaft
MD998382
Oil seal
MD998285
(Lubricate outer
circumference with oil)

ENGINE – T iming Belt 11-27
(3) Make sure that the relationship between the tensioner
pulley center and the bolt center is as shown in the
illustration.
(4) Move the tensioner “B” in the direction of arrow while
lifting with a finger to give a sufficient tension to the tension
side of timing belt. In this condition, tighten bolt to secure
tensioner “B” . When the bolt is tightened, use care to
prevent shaft from turning together. If shaft is turned
together, belt will be overtensioned.
 H
CRANKSHAFT BOLT TIGHTENING
 I
OIL PUMP SPROCKET INSTALLATION
(1) Block the counterbalance shaft in the same way as at the disassembly to prevent it from turning.
(2) Install the oil pump sprocket.
(3) Apply a proper amount of engine oil to the bearing surfaces
of the flange nuts.
(4) Tighten the flange nuts to the specified torque.
 J
AUTO TENSIONER INSTALLATION
(1) If the auto tensioner rod is in its fully extended position, reset it as follows.
a. Clamp the auto-tensioner in the vise with soft jaws.
b. Push in the rod little by little with the vise until the
set hole A in the rod is aligned with the hole B in
the cylinder.
Tensioner “B”
Timing belt “B”
Tension side
of timing belt
Center of
tensioner
pulley
Center
of bolt
6EN0564
6AE0049
A
B

ENGINE – T iming Belt 11-31
(17)Loosen the retaining bolt of the tensioner pulley.
Caution
Loosening the retaining bolt can cause the intake
and exhaust camshafts to turn, resulting in slackened
timing belt. Use care that the timing belt does not
come off the sprockets at this time.
(18)Pull up the slack of the timing belt by turning the tensioner in illustrated direction using the special tool and a torque
wrench (0 – 5 Nm {0 – 0.5 kgf
m}).
(19)From this position, turn back the tensioner until the torque wrench reading becomes 3.5 Nm {0.36 kgf
m}, then
secure it by tightening the retaining bolt.
(20)Remove the special tool attached in step (16).
(21)Rotate the crankshaft clockwise 2 turns. Then, leave it intact 15 minutes.
(22)Check to see that the wire inserted when installing the
auto-tensioner can be pulled out lightly. If it can be pulled
out lightly, the timing belt is being tensioned properly.
If so, remove the wire. In addition, check that the rod
protrusion from the auto-tensioner meets the standard
value, which is also an indication of properly tensioned
timing belt.
Standard value: 3.8 – 4.5 mm
(23)If the wire cannot be removed with a light force, repeat steps (16) through (21) until the proper belt tensioner
is obtained.MD998767

INTAKE AND EXHAUST – Intercooler15-7
INTERCOOLER
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Front Bumper Removal and Installation
(Refer to GROUP 51.)
16
Unit: Nm {kgf
m}
10 – 13
{1.0 – 1.3} 6 {0.6}
10 – 13
{1.0 – 1.3} 10 – 13
{1.0 – 1.3}
10 – 13
{1.0 – 1.3}
11 1 0
1213
15
1454 2
36 7
9 8
Hose clamp
tightening torque
1
Removal steps
1. Vacuum hose connection
2. Air bypass valve assembly
3. Breather hose connection
4. Vacuum hose connection
5. Air intake hose assembly
A6. Air bypass hose
7. Air hose connection
A8. Air hose DA9. Air hose C
A10. Air hose A
11. Air pipe A
A12. Air hose B
13. Intercooler assembly
A14. Air hose B
15. Air pipe B
16. Air pipe bracket
INSTALLATION SERVICE POINT
AAIR HOSE B / AIR HOSE A / AIR HOSE C / AIR
HOSE D / AIR BYPASS HOSE INSTALLATION
Align the alignment mark (white paint) on each hose with
the protrusion on each pipe.

INTAKE AND EXHAUST – Exhaust Pipe and Muffler15-14
EXHAUST PIPE AND MUFFLER
REMOVAL AND INSTALLATION
Unit: Nm {kgf
m}
15
44 {4.5}
49 {5.0}
34 {3.5}
5 {0.5}13 {1.3}
14
16
7 5 13
172 1
3
46 18
8
9 12
10 11
34 {3.5}
19 {1.9}49 {5.0}
Hanger mounting bolt tightening
torque
13 {1.3}
3, 9, 18
93 3 9
Main muffler removal steps
1. Bolt
2. Main muffler
3. Hanger
Center exhaust pipe removal steps
1. Bolt
4. Spring
5. Heat protector
6. Self-locking nut
7. Hanger bracket
8. Center exhaust pipe
9. Hanger
10. Protector11. High-temperature sensor
12. Bolt
13. Catalytic converter
14. Front floor heat protector panel
Front exhaust pipe removal steps
4. Spring
5. Heat protector
12. Bolt
15. Self-locking nut
16. Front exhaust pipe
17. Front exhaust pipe bracket
18. Hanger

MANUAL TRANSMISSION – On-vehicle Service22A-3
ON-VEHICLE SERVICE
1. TRANSMISSION OIL CHECK
(1) Remove the oil filler plug.
(2) Oil level should be at the lower portion of the filler plug
hole.
(3) Check that the transmission oil is not noticeably dirty,
and that it has a suitable viscosity.
(4) Tighten the filler plug to the specified torque.
Tightening torque: 32 Nm {3.3 kgfm}
2. TRANSMISSION OIL REPLACEMENT
(1) Remove the drain plug to drain oil.
(2) Tighten the drain plug to the specified torque.
Tightening torque: 32 Nm {3.3 kgfm}
(3) Remove the filler plug and fill with specified oil till the
level comes to the lower portion of filler plug hole.
Transmission oil
Specified oil:
MITSUBISHI genuine “Dia-Queen” multi gear oil
<75W/85W>
Quantity: 2.8 dm
3 (2.8
)
(4) Tighten the filler plug to the specified torque.
Tightening torque: 32 Nm {3.3 kgfm}
3. TRANSFER OIL CHECK
(1) Remove the oil filler plug.
(2) Oil level should be at the lower portion of the filler plug
hole.
(3) Check that the transmission oil is not noticeably dirty,
and that it has a suitable viscosity.
(4) Tighten the filler plug to the specified torque.
Tightening torque: 32 Nm {3.3 kgfm}
4. TRANSFER OIL REPLACEMENT
(1) Remove the drain plug to drain oil.
(2) Tighten the drain plug to the specified torque.
Tightening torque: 32 Nm {3.3 kgfm}
(3) Remove the filler plug and fill with specified oil till the
level comes to the lower portion of filler plug hole.
Transfer oil
Specified oil:
MITSUBISHI genuine “Dia-Queen Super” hypoid
gear oil (GL-5)
Quantity: 0.62 dm
3 (0.62
)
(4) Tighten the filler plug to the specified torque.
Tightening torque: 32 Nm {3.3 kgfm}
Transmission oilFiller plug hole
Filler plug
Drain plug
Filler plug
Drain plug
Transfer oil

22B-1
MANUAL
TRANSMISSION
OVERHAUL
CONTENTS
GENERAL INFORMATION 2. . . . . . . . . . . . . . . .
SPECIFICATIONS 4. . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 4. . . . . . . . . . . . . .
SEALANTS AND ADHESIVES 5. . . . . . . . . . . .
LUBRICANTS 6. . . . . . . . . . . . . . . . . . . . . . . . . . .
SNAP RINGS, SPACERS AND THRUST
PLATES FOR ADJUSTMENT 6. . . . . . . . . . . . .
TORQUE SPECIFICATIONS 9. . . . . . . . . . . . . .
SPECIAL TOOLS 10. . . . . . . . . . . . . . . . . . . . . .
TRANSMISSION 13. . . . . . . . . . . . . . . . . . . . . . .
INPUT SHAFT 20. . . . . . . . . . . . . . . . . . . . . . . . . OUTPUT SHAFT 27. . . . . . . . . . . . . . . . . . . . . . .
REVERSE IDLER GEAR 35. . . . . . . . . . . . . . .
SPEEDOMETER GEAR 36. . . . . . . . . . . . . . . .
SELECT LEVER 37. . . . . . . . . . . . . . . . . . . . . . .
CONTROL HOUSING 38. . . . . . . . . . . . . . . . . .
CLUTCH HOUSING 41. . . . . . . . . . . . . . . . . . . .
TRANSMISSION CASE 44. . . . . . . . . . . . . . . . .
CENTER DIFFERENTIAL 46. . . . . . . . . . . . . . .
TRANSFER 49. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Snap Rings, Spacers and Thrust Plates
for Adjustment / Torque Specifications MANUAL TRANSMISSION
OVERHAUL –22B-9
Part namePart No. Identification symbol Thickness mm
Spacer
(For adj stment of center differential case
1.19LMD710456
(For adjustment of center differential case
preload)1.22GMD700271p
1.25MMD710457
1.28NMD710458
1.31EMD706574
Spacer
(For adj stment of center differential case pinion
0.6–MD748362
(For adjustment of center differential case pinion
backlash)0.7–MD748363
0.8–MD748364
0.9–MD748365
1.0–MD748366
1.1–MD748367
TORQUE SPECIFICATIONS
TRANSMISSION
ItemsNm {kgf
m}
Under cover mounting bolt6.9 {0.7}
Interlock plate bolt30 {3.1}
Clutch housing-transmission case mounting bolt44 {4.5}
Clutch release bearing retainer mounting bolt9.8 {1.0}
Control housing mounting bolt18 {1.9}
Shift cable bracket mounting bolt18 {1.9}
Speedometer gear mounting bolt3.9 {0.4}
Stopper bracket mounting bolt18 {1.9}
Select lever mounting bolt18 {1.9}
Select lever mounting nut11 {1.2}
Center differential drive gear mounting bolt132 {13.5}
Back-up lamp switch32 {3.3}
Poppet spring plug32 {3.3}
Reverse idler gear shaft mounting bolt48 {4.9}
Roll stopper bracket mounting bolt69 {7.0}

Torque Specifications /
Special toolsMANUAL TRANSMISSION OVERHAUL – 22B-10
TRANSFER
ItemsNm {kgf
m}
Transfer cover mounting bolt23 {2.4}
Transmission-transfer mounting bolt69 {7.0}
SPECIAL TOOLS
ToolNumberNameUse
MB990887Arm bushing
remover & installer
ringInstallation of transfer oil seal
MB990891Bushing remover &
installer baseInstallation of transfer oil seal
MB990928Installer adapterInstallation of input shaft oil seal
MB990932Installer adapterRemoval of differential case taper roller bearing
MB990933Installer adapterInstallation of transfer oil seal
MB990935Installer adapterInstallation of output shaft front taper roller
bearing outer race
MB990937Installer adapterInstallation of differential case taper roller
bearing