battery MITSUBISHI LANCER EVOLUTION VI 1999 User Guide

MPI – Troubleshooting13-29
INSPECTION PROCEDURE 12
When the engine is hot, it stalls at idling. (Die out)
Probable cause
In such cases as the above, the cause is probably that ignition system, air/fuel mixture,
idle speed control (ISC) or compression pressure is defective.
In addition, if the engine suddenly stalls, the cause may also be a defective connector
contact.
Malfunction of the ignition system

Malfunction of air-fuel ratio control system

Malfunction of the ISC servo system

Drawing air into intake system

Improper connector contact

Backflow of secondary air to the intake system
Were the battery terminals disconnected recently?Ye sAfter warming-up, let the engine run at idling for about 10 minutes.
No
MUT-II Diagnosis code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Check the ISC servo for operation sound.NGCheck the ISC servo system.
(Refer to P.13-44, INSPECTION PROCEDURE 33.)
OK
Check the injector for operation sound.NGCheck the injector system. (Refer to P.13-15, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)
OK
Does the engine stall right after the accelerator pedal is released?Ye sClean the throttle valve
area.Adjust the fixed SAS.
(Refer to P.13-30.)*
No
Does the engine stall easily again?NoWhile carrying out an intermittent malfunction simulation test (Refer
to GROUP 00 – Points to Note for Intermittent Malfunctions.), check
for sudden changes in the signals shown below.

Crank angle sensor signal

Injector drive signal

Fuel pump drive signal

Air flow sensor signal
Secondary ignition signal

Engine-ECU power supply
voltage
Ye s
MUT-II: Engine stalling inspection when the engine is warm and
idling. (Refer to P.13-50, INSPECTION PROCEDURE 42.)
OK
Check the ignition timing.
(Refer to GROUP 11 – ENGINE ADJUSTMENTS.)*NGCheck that the crank angle sensor and the timing belt cover are
installed properly.
OK
Check the following items.

Check the ignition coil, spark plugs, spark plug cables.

Check the secondary air supply system. (Ensure that there is no backflow of secondary air into the intake system.)

Check if the injectors are clogged.

Check the compression pressure.

Check if foreign materials (water, alcohol, etc.) got into fuel.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).

MPI – Troubleshooting13-30
INSPECTION PROCEDURE 13
The engine stalls when starting the car. (Pass out)
Probable cause
In cases such as the above, the cause is probably misfiring due to a weak spark,
or an inappropriate air/fuel mixture when the accelerator pedal is depressed.
Drawing air into intake system

Malfunction of the ignition system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Check the following items.

Check the ignition coil, spark plugs, spark plug cables.

Check if air was drawn into the intake system.
Broken intake manifold gasket
Broken or disconnected vacuum hose
Improper operation of the PCV valve
Broken air intake hose
INSPECTION PROCEDURE 14
The engine stalls when decelerating.
Probable cause
In cases such as the above, the cause is probably that the intake air volume is insufficient
due to a defective idle speed control (ISC) servo system.
Malfunction of the ISC servo system
No
MUT-II Data list
26 Idle position switch (Refer to P.13-XX.)NGCheck the idle position switch system.
(Refer to P.13-XX, INSPECTION PROCEDURE 26.)
OK
MUT-II Data list
14 Throttle position sensor (Refer to P.13-57.)NGCheck the throttle position sensor system. (Refer to P.13-9, IN-
SPECTION PROCEDURE FOR DIAGNOSIS CODE 14.)
OK
MUT-II Data list
45 ISC servo position

Is the idle speed control (ISC) servo position drops to 0–2
steps when decelerating (engine r/min less than 1,000)?Ye sCheck the vehicle speed sensor system. (Refer to P.13-13, INSPEC-
TION PROCEDURE FOR DIAGNOSIS CODE 24.)
No
Check the following items.

Check the ignition coil, spark plugs, spark plug cables.

Clean the throttle valve area.

Check and adjust the fixed SAS.
No
MUT-II Data list
26 Idle position switch (Refer to P.13-58.)NGCheck the idle position switch system.
(Refer to P.13-38, INSPECTION PROCEDURE 26.)
No
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
Were the battery terminals disconnected recently?Ye sAfter warming-up, let the engine run at idling for about 10 minutes.

MPI – Troubleshooting13-35
INSPECTION PROCEDURE 23
Low alternator output voltage (approx. 12.3 V)
Probable cause
The alternator may be defective, or malfunctions, which are listed in the right column,
may be suspected.
Malfunction of charging system

Short circuit in harness between alternator G terminal
and engine-ECU

Malfunction of engine-ECU
Measure at the alternator connector
side. A-05

Connect the connector.
(Test harness: MB991519)

Voltage between 1 (black clip) and
earth
Engine: at idle
Radiator fan: does not run
Headlamp: OFF → ON
Brake lamp: OFF → ON
Rear defogger switch:
OFF → ON
OK:Voltages rises
by 0.2 – 3.5 V.NGMeasure at the alternator connector.
A-05

Disconnect the connector, and
measure at the harness side.

Disconnect the engine-ECU con-
nector.

Continuity between 1 and earth
OK:No continuityNGCheck the harness wire between the
alternator and the engine-ECU connec-
tor, and repair if necessary.
OK
Check the alternator.
OK
Check the harness wire between the
alternator and the engine-ECU connec-
tor.NG
Repair
OK
Replace the engine-ECU.
INSPECTION PROCEDURE 24
Power supply system and ignition switch-IG system
Probable cause
When an ignition switch ON signal is input to the engine-ECU, the engine-ECU turns
the control relay ON. This causes system voltage to be supplied to the engine-ECU,
injectors and air flow sensor.
Malfunction of the ignition switch

Malfunction of the control relay

Improper connector contact, open or short-circuited
harness wire

Disconnected engine-ECU earth wire

Malfunction of the engine-ECU
Check the control relay. (Refer to P.13-68.)NG
Replace
OK
Measure at the control relay connector B-27.

Disconnect the connector, and measure at the harness side.

Voltage between 3, 4 and earth
OK:System voltageNGCheck the following
connector: A-28NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between battery and control relay connector,
and repair if necessary.
OK
Check the engine-ECU power supply and earth circuit.
(Refer to P.13-53, INSPECTION PROCEDURE 45.)

MPI – Troubleshooting13-53
INSPECTION PROCEDURE 45
Check the engine-ECU power supply and earth circuit.
Measure at the engine-ECU connectors, B-59, B-60, B-62.

Disconnect the connector and measure at the harness side
1. Voltage between 82 and earth (Ignition switch: ON)
OK:System voltage
2. Voltage between 38 and earth
OK:System voltage
3. Voltage between 12, 25 and earth (Ignition switch: ON)
OK:System voltage (when the terminal 38 is earthed)
4. Continuity between 13, 26 and earth
OK:Continuity
5. Voltage between 80 and earth
OK:System voltage1. NGCheck the following
connectors: B-65, B-76NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire
between engine-ECU and
ignition switch connector.NG
Repair
OK
Check the ignition switch. (Refer to GROUP 54.)
2, 3. NG
4. NG
Check the harness wire between engine-ECU and earth, and repair
if necessary.
5. NG
OK
Check the following
connectors:
B-59, B-60, B-62NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
Check the following connectors:
B-65, B-49, B-75, B-73NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between engine-ECU and battery, and
repair if necessary.
Check the harness wire between engine-ECU and control relay
connector, and repair if necessary.
INSPECTION PROCEDURE 46 <EVOLUTION-IV, EVOLUTION-V>
Check fuel pump circuit.
Measure at the fuel pump connector D-18.

Disconnect the connector and measure at the harness side.

Continuity between 1 and earth
OK:ContinuityNGCheck the following connector:
D-04NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between fuel pump and earth, and repair
if necessary.
OK
Check the following connectors: D-04, B-64NG
Repair OKCheck trouble symptom.
NG
Check the harness wire between terminal for fuel pump drive and
fuel pump connector.NG
Repair
OK
Replace the fuel pump.

MPI – On-vehicle Service13-68
ON-VEHICLE SERVICE
FUEL PUMP RESISTOR CHECK
<EVOLUTION-VI>
Standard value: 0.45 – 0.65 Ω
The inspection procedures are the same as for the preceding
year-models.
FUEL PUMP RELAY No.2 CONTINUITY CHECK
<EVOLUTION-VI>
Battery voltageTerminal No.
1234
Not supplied
Supplied
ENGINE CONTROL RELAY AND FUEL PUMP
RELAY CONTINUITY CHECK
Battery voltageTerminal No.
1234
Not supplied
Supplied
Equipment side connector for engine
control relay and fuel pump relay
Fuel pump relay
Engine control relay

27-1
REAR AXLE
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 2. . . . . . . . . . . . . .
LUBRICANT 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 3. . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING <AYC> 4. . . . . . . . . . . . .
ON-VEHICLE SERVICE
<VEHICLES WITH AYC> 31. . . . . . . . . . . . . . .
Rear Axle Total Backlash Check 31. . . . . . . . . . .
Gear Oil Level Check 31. . . . . . . . . . . . . . . . . . . .
Gear Oil Change 32. . . . . . . . . . . . . . . . . . . . . . . . .
Fluid Level Check 33. . . . . . . . . . . . . . . . . . . . . . . . Bleeding 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AYC Operation Check 34. . . . . . . . . . . . . . . . . . . .
Hydraulic Pressure Check 35. . . . . . . . . . . . . . . . .
Differential Carrier Oil Seal
Replacement 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Speed Sensor Output Voltage
Measurement <Vehicles without ABS> 37. . . . .
Action When Battery Runs Out 38. . . . . . . . . . . .
HYDRAULIC UNIT
<VEHICLES WITH AYC> 39. . . . . . . . . . . . . . .
SENSOR RELAY
<VEHICLES WITH AYC> 41. . . . . . . . . . . . . . .
AYC-ECU 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

REAR AXLE – Troubleshooting <AYC>27-6
4. INSPECTION PROCEDURES FOR DIAGNOSIS CODES
Code No. 12: Power supply voltage (valve power supply)
systemProbable cause
This code is output when the AYC-ECU power supply voltage drops below, goes
beyond, a specified level.
Defective harness or connector

Defective battery

Defective AYC-ECU
NOTE
Refer to the corresponding item if any other diagnosis code is being output.
Is the battery voltage correct?NG
Replace
OK
Measure at B-96 AYC-ECU connector.

Disconnect the connector and
measure at the harness side.

Ignition switch: ON

Voltage across 31 and body ground
OK:System voltageNGCheck the following connectors:
B-96, B-94, B-49, B-75, B-76
OK
Check the trouble symptom.
NG
Check and repair harness between
ignition switch (IG
2) and AYC-ECU. OKReplace AYC-ECU.NG
Repair
Code Nos. 21, 22, 23, 24: Wheel speed sensor systemProbable cause
This code is output if any one of three wheel speed sensors fails to provide an input
even after the other wheel exceeded 8 km/h.
Defective harness or connector

Defective ABS-ECU

Defective AYC-ECU
<Vehicles with ABS>
NG
Replace AYC-ECU.
OK
Replace ABS-ECU.
NG
Check harness between AYC-ECU
and ABS-ECU.NG
Repair
OK
Check the trouble symptom.
Is an ABS diagnosis code No. 21, 22,
23, or 24 output?YESRefer to Group 35B – Troubleshooting
NO
Measure at B-95 AYC-ECU connector.

Disconnect the connector and
measure at the harness side.

Ignition switch: ON

Turn tire at 1/2 to 1 revolution/sec.

Voltage across 6/7/8/9 and body
ground
OK:42 mV or more (when mea-
sured with a circuit tester)
120 mV-P or more (when
measured with an oscillo-
scope)OKCheck the following connector:
B-95
OK
Check the trouble symptom.
NG
Check the following connectors:
B-24, B-95NG
RepairNG
Repair

REAR AXLE – Troubleshooting <AYC>27-25
DATA LIST REFERENCE TABLE
The following items can be read by t01he MUT-

from the ECU input data.
Item No.
Check itemChecking requirementsNormal value
01Front-right wheel speedPerform a test run.Vehicle speeds
displayed on the
02Front-left wheel speed
displayed on the
speedometer and
MUTIIare identi03Rear-right wheel speedMUT-II are identi-
cal.
04Rear-left wheel speed
05Front-right wheel speed
(0.2 km/h)
06Front-left wheel speed (0.2
km/h)
07Rear-right wheel speed
(0.2 km/h)
08Rear-left wheel speed (0.2
km/h)
10Vehicle speed
11System voltageIgnition switch: ONBattery voltage
15TPS openingAccelerator pedal position/Igni-
tion switch: ON
Fully closed300 – 1000mV
tion switch: ON
Partially openGradually increases
from the above val-
ue.
Fully open4500 – 5000mV
19Longitudinal acceleration
sensor
Vehicle stands on level ground2.4 – 2.6V
sensor
Perform a test run.Reading fluctuates
up or down with 2.5V
as its center.
20Lateral acceleration sensorVehicle stands on level ground2.4 – 2.6V
Perform a test run.Reading fluctuates
up or down with 2.5V
as its center.
22Steering wheel operationSteering wheel turning direction
Ignition switch: ON90 deg. clock-
wiseR90 deg
90 deg counter-
clockwiseL90 deg
23Steering wheel turning
angular velocity
Steering wheel position
Ignition switch: ON
Not turned0 deg/s
angular velocityIgnition switch: ON
TurnedReading varies ac-
cording to turning
speeds.
45Idle position switchAccelerator pedal position
Ignition position: ON
Not depressedON
Ignition position: ON
DepressedOFF

REAR AXLE – On-vehicle Service <Vehicles with AYC>27-38
Waveform Observation Points
SymptomProbable causeAction
Waveform amplitude is too small, or no
waveform.Defective wheel speed sensorReplace sensor.
Waveform amplitude varies greatly. (No
problem ifthe smallest amplitude is 100
Excessive axle hub lateral and radial runoutReplace hub.
problem if the smallest amplitude is 100
mV or more)Poor AYC-ECU groundingRepair.
Noise on waveform or disturbed
waveform
Open-circuited sensorReplace sensor.
waveform
Open-circuited harnessRepair harness.
Improperly mounted wheel speed sensorCorrect sensor installation.
Missing or collapsed ABS rotor toothReplace ABS rotor.
Caution
Since the wheel speed sensor cable follows the movement of the front or rear suspension, it
may be open-circuited only when the vehicle is run on rough roads and not on ordinary road.
The wheel speed sensor output voltage waveform should therefore be checked also by rocking
the sensor harness so that driving on rough roads may be simulated.
ACTION WHEN BATTERY RUNS OUT
When the engine is started using a booster cable where the
battery has completely run down and you attempt to start
the vehicle without waiting for the battery to recover a certain
charge, the engine can misfire and you just cannot start to
move it. In such cases, charge the battery sufficiently; or,
remove the AYC fusible link from the engine compartment
relay box to make AYC inactive before attempting to start
the vehicle. When the fusible link is removed, the AYC warning
lamp lights up. After the battery has been recharged, fit the
fusible link back again and start the engine to ensure that
the AYC warning lamp is off.AYC fusible link

REAR AXLE – Sensor Relay <Vehicles with AYC> / AYC-ECU27-42
INSPECTION
1. LONGITUDINAL AND LATERAL ACCELERATION
SENSOR CHECK
Refer to GROUP 35B – Acceleration Sensor.
2. AYC RELAY CONTINUITY CHECK
Battery voltageTerminal No.
1345
When not energized
When energized
AYC-ECU
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation

Front Floor Console Removal and Installation
5 Nm
AYC-ECU
5 Nm