wheel MITSUBISHI MONTERO 1991 Repair Manual
Page 656 of 1333
LO CKIN G H UBS
1991 M it s u bis h i M onte ro
1991 DRIVE AXLES
Locking Hubs
Mitsubishi: Montero, Pickup
DESCRIPTION
Automatic hubs are engaged by rotational force of axle shaft
when 4WD is selected at transfer case. Automatic hubs disengage when
2WD is selected or vehicle is driven in Reverse. Cams, brakes and
springs are used to lock or unlock automatic hubs.
Engagement is accomplished through gears and spring actions
within hub. When hub is locked, hub brake engages inner hub, which is
connected to axle shaft by inner splines of hub. Hub brake is
connected to hub body by outer splines.
REMOVAL
1) Hub must be unlocked. To unlock hub, place transfer case
lever in 2H position and move vehicle in Reverse approximately 4-6
feet.
2) Remove cover from locking hub. If hub cover cannot be
loosened by hand, wrap shop towel around cover and use an oil filter
wrench to loosen cover.
3) Raise and support vehicle. Remove wheel assembly. Using
snap ring pliers, remove snap ring and shim from end of axle. Remove
locking hub retaining bolts. Remove locking hub.
INSTALLATION
1) To install, reverse removal procedure. Apply sealant to
contact areas between locking hub assembly and hub/rotor assembly.
Ensure sealant is NOT applied on outer areas of hub/rotor assembly
toward brake contact areas.
2) Align locking hub assembly key area with steering knuckle
key way area. Loosely install locking hub assembly on hub/rotor
assembly. Ensure locking hub assembly fully contacts hub/rotor
assembly.
3) Install locking hub retaining bolts. Tighten bolts to 36-
43 ft. lbs. (49-58 N.m). Using spring scale attached to wheel stud,
measure turning resistance required to rotate hub/rotor assembly.
4) Turning resistance should NOT exceed 3.1 lbs. (1.4 kg). I\
f
turning resistance exceeds specification, check for incorrect
installation of locking hub assembly or components.
5) Install shim and snap ring on drive axle. Rotate drive
axle until maximum end play is obtained. Using a dial indicator, check
drive axle end play.
6) Drive axle end play should be .008-.020" (.20-.51 mm). If\
axle end play is NOT within specification, adjust end play by changing
axle shaft shim. Install hub cover. Tighten hub cover 13-25 ft. lbs.
(18-34 N.m).
OVERHAUL
DISASSEMBLY
Page 660 of 1333
MAIN TE N AN CE IN FO RM ATIO N
1991 M it s u bis h i M onte ro
1983-96 MAINTENANCE
Mitsubishi Maintenance Information
Montero
* PLEASE READ THIS FIRST *
NOTE: For scheduled maintenance intervals and the related fluid
capacities, fluid specifications and labor times for major
service intervals, see SCHEDULED SERVICES article below:
* SCHEDULED SERVICES - 1983-86
* SCHEDULED SERVICES - 1987-95
* SCHEDULED SERVICES - 1996
Warranty information and specifications for fluid
capacities, lubrication specifications, wheel and tire size,
and battery type are covered in this article.
MODEL IDENTIFICATION
VIN LOCATION
The Vehicle Identification Number (VIN) is located on the
left side of the dash panel at the base of the windshield. The VIN
chart explains the code characters.
VIN CODE ID EXPLANATION
Numbers preceding the explanations in the legend below refer
to the sequence of characters as listed on VIN identification label.
See VIN example below.
\
\
\
\
\
\
(VIN) J A 4 F J 4 3 E 1 H J 0 0 0 0 0 1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
\
\
\
\
\
\
1 - Manufacturing Country
J
* Japan
2 - Manufacturer
A * Mitsubishi Motor Corp.
3 - Vehicle Type
4 * Multi-Purpose Vehicle
7 * Truck
4 - GVW & Brake Type
F * 4001-5000 Lbs., Hydraulic Brakes
G * 5001-6000 Lbs., Hydraulic Brakes
5 - Vehicle Line
J, K Or R * Montero
6 - Vehicle Series
2 * Low
3 * Medium
Page 662 of 1333
operating conditions.
Normal Service
* Driven More Than 10 Miles Daily
* No Operating Conditions From Severe Service Schedule
Severe Service (Unique Driving Conditions)
* Short Trips In Freezing Temperatures
* Towing Or Commercial Use
* Driving Off-Road Or In Salty Or Sandy Areas
* Severe Dust Conditions
* Hot Weather, Stop-And-Go Driving
* Extensive Idling
CAMSHAFT TIMING BELT
CAUTION: Failure to replace a faulty camshaft timing belt may result
in serious engine damage.
The condition of camshaft drive belts should always be
checked on vehicles which have more than 50,000 miles. Although some
manufacturers do not recommend belt replacement at a specified
mileage, others require it at 60,000-100,000 miles. A camshaft drive
belt failure may cause extensive damage to internal engine components
on most engines, although some designs do not allow piston-to-valve
contact. These designs are often called "Free Wheeling".
Many manufacturers changed their maintenance and warranty
schedules in the mid-1980's to reflect timing belt inspection and/or
replacement at 50,000-60,000 miles. Most service interval schedules in
this manual reflect these changes.
Belts or components should be inspected and replaced if any
of the following conditions exist:
* Cracks Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
Replace camshaft timing belt at 60,000 mile intervals.
SERVICE POINT LOCATIONS
Fig. 1: Service Point Locations (1983-86 2.6L 4-Cylinder Engine)
Courtesy of Mitsubishi Motor Sales of America.
Page 668 of 1333
1994-96 (3.0L DOHC & 3.5L) .................. 9.0 Qts. (8.5L)
Cooling System
1983-88 ..................................... 8.5 Qts. (8.0L)
1989-96
2.6L ....................................... 9.7 Qts. (9.2L)
3.0L ...................................... 10.0 Qts. (9.5L)
3.5L ...................................... 10.0 Qts. (9.5L)
Differential
1983-88 ..................................... 1.9 Qts. (1.8L)
1989-93
2.6L ....................................... 1.9 Qts. (1.8L)
3.0L ....................................... 2.7 Qts. (2.6L)
1994-96
3.0L & 3.5L ................................ 2.7 Qts. (2.6L)
Engine Oil
1983-86 ..................................... 6.0 Qts. (5.8L)
1987 ........................................ 5.2 Qts. (5.0L)
1988 ........................................ 5.0 Qts. (4.8L)
1989-91 ..................................... 5.5 Qts. (5.3L)
1992-96 ..................................... 5.2 Qts. (4.9L)
Power Steering ................................ 1.1 Qts. (1.0L)
Fuel Tank
1983-88 .................................... 15.9 Gals. (60L)
1989-90
2.6L 2-Door ............................... 15.9 Gals. (60L)
3.0L 2-Door ............................... 19.9 Gals. (75L)
2.6L & 3.0L 4-Door .......................... 24 Gals. (92L)
1991-96 ...................................... 24 Gals. (92L)
Manual Transmission
1983-91 ..................................... 2.3 Qts. (2.2L)
1992 ........................................ 2.4 Qts. (2.3L)
1993-96 ..................................... 2.6 Qts. (2.5L)
Transfer Case
1983-91 ..................................... 2.3 Qts. (2.2L)
1992-96 ..................................... 2.4 Qts. (2.3L)
(1) - Use of R12 in a R134a system will result in SEVERE DAMAGE.
( 2) - 1983 model equipped with manual transmission only.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE
\
\
\
\
\
\
Wheel Size Tire Size
1983-86
15 x 6JJ (Steel) .............................. 215 SR15
1987-88
Page 669 of 1333
15 x 6JJ (Steel) ........................... P225/75 R15
1989-1996
15 x 6JJ (Steel) ........................... P225/75 R15
15 x 6JJ (Steel or Aluminum) ............... P235/75 R15
15 X 7JJ (Aluminum) ........................ 31-10.50R15
\
\
\
\
\
\
TIRE INFLATION SPECIFICATIONS TABLE\
\
\
\
\
\
Application Pressure
psi (kg/cm )
1983-88
Front ( 1) ..................................... 26 (1.8)
Rear .......................................... 34 (2.3)
Rear ...................................... ( 2) 26 (1.8)
1989-91
Front ( 1) ..................................... 26 (1.8)
Rear .......................................... 35 (2.4)
Rear ...................................... ( 2) 26 (1.8)
1992-96
P235/75R15
Front ........................................ 26 (1.8)
Rear ......................................... 35 (2.4)
31-10.50R15
Front ........................................ 29 (2.1)
Rear ......................................... 40 (2.8)
( 1) - No chain clearance.
( 2) - Inflation pressure for better ride comfort when
driving with no cargo.
\
\
\
\
\
\
WHEEL TIGHTENING
WHEEL TIGHTENING SPECIFICATIONS TABLE\
\
\
\
\
\
Application Ft. Lbs. (N.m.)
1983 ....................................... 50-57 (70-80)
1984-96 .................................. 72-87 (100-120)
\
\
\
\
\
\
BATTERY SPECIFICATIONS
CAUTION: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
COMPUTER RELEARN PROCEDURES article in the GENERAL
INFORMATION Section.
Battery is maintenance-free and does not normally require
additional water. However, under severe conditions it is advisable to
check battery fluid periodically. Use only distilled water to fill
battery cell should it become necessary to add water. Charge condition
can be checked by a visual test indicator on top of battery.
BATTERY REPLACEMENT SPECIFICATIONS TABLE
\
\
\
\
\
\
Application BCI Group Number
Page 670 of 1333
2.6L Engine ........................................... 45
2.6L Optional ......................................... 45
3.0L V6 ........................................... (1) 24
3.5L V6 ........................................... ( 1) 24
( 1) - Check hood clearance on 1986 and newer models.
\
\
\
\
\
\
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG SYSTEM
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
The SRS has no user-servicable parts. Always have servicing
done by an authorized dealer.
When performing maintenance on air bag equipped vehicles
always observe proper safety precautions.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
ANTI-LOCK BRAKE SYSTEM (ABS)
CAUTION: Never mix different diameter tires. On loose or uneven
surfaces, the ABS system may require longer stopping
distances than conventional brake systems. Exercise caution
when removing mud or snow from the wheels so as not to
damage the ABS wiring or speed sensors.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
Page 684 of 1333
\003
PR E-A LIG NM EN T C HEC KS
1991 M it s u bis h i M onte ro
Wheel Alignment
PRE-ALIGNMENT INSPECTION PROCEDURES
PRE-ALIGNMENT CHECKS
Before making wheel alignment adjustment, perform the
following checks:
1) Tires should be equal in size and runout must not be
excessive. Tires and wheels should be in balance, and inflated to
manufacturer's specifications.
2) Wheel bearings must be properly adjusted. Steering linkage
and suspension must not have excessive looseness. Check for wear in
tie rod ends and ball joints.
3) Steering gear box must not have excessive play. Check and
adjust to manufacturer's specifications.
4) Vehicle must be at curb height with full fuel load and
spare tire in vehicle. No extra load should be on vehicle.
5) Vehicle must be level with floor and with suspension
settled. Jounce front and rear of vehicle several times and allow it
to settle to normal curb height.
6) If steering wheel is not centered with front wheels in
straight-ahead position, correct by shortening one tie rod adjusting
sleeve and lengthening opposite sleeve equal amounts.
7) Ensure wheel lug nuts are tightened to torque
specifications.
Page 693 of 1333
intake hoses and EGR pipe. Disconnect oxygen sensor electrical
connector.
2) Remove oil pipe and EGR valve. Disconnect exhaust fitting
and remove rear heat protector. Remove oil return pipe. Remove
turbocharger assembly. See Fig. 11.
Fig. 11: Removing Rear Turbocharger (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Inspection
Check turbine and compressor wheels for cracking and other
damage. Make sure turbine and compressor wheels turn smoothly. Check
for oil leakage from turbocharger assembly. Check for proper wastegate
valve operation. See SYSTEM & COMPONENT TESTING article.
Installation
1) To install, reverse removal procedure. Before oil pipe
flare nut (above turbocharger) is installed, pour clean engine oil
into turbocharger. Ensure oil and air hoses are properly installed and
securely clamped.
2) Use new gaskets. Adjust accelerator cable (if necessary).\
Refill engine oil and coolant. Check for oil and coolant leaks.
Tighten all bolts to specification. See TORQUE SPECIFICATIONS table.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Applications Ft. Lbs. (N.m)
Fuel Tank Nuts ............................. 15-22 (20-30)
Page 695 of 1333
RID IN G H EIG HT A D JU STM EN T
1991 M it s u bis h i M onte ro
1991-92 WHEEL ALIGNMENT
Riding Height Adjustment
Chrysler Motors: Ram-50
Mitsubishi: Montero, Pickup
RIDING HEIGHT ADJUSTMENT
Before adjusting alignment, check riding height. Ensure
vehicle is on level floor and tires are properly inflated. Bounce
vehicle several times and allow suspension to settle.
Visually inspect vehicle, from front to rear or side to
side, for signs of abnormal height. Remove extra heavy items from
passenger and luggage compartments. If riding height is not within
specification, check and repair suspension before adjusting alignment.
See RIDING HEIGHT SPECIFICATIONS (FRONT) table.
RIDING HEIGHT SPECIFICATIONS (FRONT) ( 1)
\
\
\
\
\
Application (2) In. (mm)
Montero ............................ 2.80 (71.1)
Pickup 4WD & Ram-50 4WD ............ 3.07 (78.0)
(1) - Ensure tire inflation is correct and vehicle
is level.
( 2) - Distance between lower control bump stopper
and bracket. See Fig. 1.
\
\
\
\
\
RIDING HEIGHT SPECIFICATIONS 1992 (FRONT) ( 1) \
\
\
\
\
Application In. (mm)
Montero .................. 0.83-0.91 (21.0-23.0)
Pickup 4WD & Ram-50 4WD ............ 3.11 (79.0)
(1) - Distance between lower control bumper and
bracket.
\
\
\
\
\
Fig. 1: Measuring Front Riding Height (Typical 4WD)
Courtesy of Mitsubishi Motor Sales of America.
Page 696 of 1333
SC HED ULE D S ER VIC ES
1991 Mitsubishi Montero
1987-95 MAINTENANCE
Mitsubishi Maintenance & Service Intervals
Montero
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES)
for items requiring additional maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (AIR BAG)
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
Modifications or improper maintenance, including incorrect
removal and installation of the Supplemental Restraint System (SRS),
can adversely affect system performance. DO NOT cover, obstruct or
change the steering wheel horn pad in any way, as such action could
cause improper function of the system. Use only plain water when
cleaning the horn pad. Solvents or cleaners could adversely affect the
air bag cover and cause improper deployment of the system.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
AIR CONDITIONING SERVICING
WARNING: R-134a service equipment or vehicle A/C systems SHOULD NOT
be pressure tested or leak tested with compressed air. Some
mixtures of air/R134a have shown to be combustible at
elevated pressures. These mixtures are dangerous and may
cause fire and/or explosions. See the appropriate
A/C SYSTEM GENERAL SERVICING article in the AIR CONDITIONING
& HEAT section.