warning light MITSUBISHI MONTERO 1998 Owner's Guide

Page 968 of 1501

allowing metal objects to contact the battery posts and the
vehicle at the same time.
CAUTION: Never disconnect the battery while the engine is running;
doing so could damage the car's electrical components.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
BRAKE FLUID
WARNING: DO NOT use reclaimed fluid or fluid that has been stored
in old or open containers. It is essential that foreign
particles and other liquids are kept out of the brake fluid
reservoir.
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
ENGINE COOLANT SERVICE
WARNING: To avoid the danger of being scalded never change the coolant
when the engine is hot.
WARNING: Never remove the radiator cap when the engine is hot Serious
burns could be caused by high pressure fluid escaping from
the radiator.
CAUTION: When adding or replacing engine coolant, use a high quality
ethylene glycol antifreeze diluted with 50% distilled water.
When putting the cap on the reserve tank, line up the arrow
on the cap and the arrow on the tank, or coolant can leak out
ENGINE DRIVE BELT SERVICE
WARNING: Be sure the ignition key is OFF. The engine could rotate
unexpectedly.
ENGINE OIL
WARNING: The engine oil may be high enough to burn your fingers
when the drain plug is loosened. Wait until the drain plug
is cool enough to touch with you bare hands.
WARNING: Continuous contact with used engine oil has been found to
cause skin cancer in laboratory animals. Brief contact with
used engine oil may irritate skin. To minimize your exposure
to used oil, wear a long sleeve shirt and moisture-proof
gloves when changing oil. If oil contacts your skin, wash

Page 972 of 1501

1 - 60 Amp
Battery
2 - 100 Amp
Alternator
3 - 20 Amp (Yellow)
Multipoint Injection
4 - 40 Amp
Ignition Switch
5 - 30 Amp (Green)
Rear Window Defogger
6 - 30 Amp (Green)
Power Window Control
7 - 30 Amp (Green)
Air Conditioner
8 - 40 Amp
Lights
9 - 10 Amp (Red)
AIR CONDITIONING & HEAT Compressor
10 - 25 Amp
Condenser Fan
11 - 10 Amp (Red)
Tail Lights
12 - 10 Amp (Red)
Headlight Upper Beam
13 - 10 Amp (Red)
Hazard Warning Flashers

Page 1007 of 1501

 (Even If Air  * SRS Control Unit 

Bag Did Not 
* Wiring Harness 

Deploy)  

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 


* DO NOT attempt SRS wiring repairs. If SRS 

 wiring or harness connectors are faulty, 

 replace faulty wiring harness. 


* After vehicle is repaired, ensure AIR BAG 

 warning light is functioning properly. 


\
\
 \
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ACURA (1996-98 SLX)\
\
\
\
\
\
\
 

Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* Sensing & Diagnostic Module (SDM) 

\
\
\b\
\
\
\
\


Inspect & If 
* Instrument Panel Braces 

Damaged, Replace 
* Instrument Panel Steering Column 

Component  Reinforcement Plate 

(Even If Air 
* Seat Belts & Mounting Points 

Bag Did Not 
* Knee Bolsters & Mounting Points 

Deploy) 
* Steering Column 


* SRS Coil Assembly 


* Wiring Harnesses 

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 


* DO NOT attempt wiring harness repairs. 

 Replace harness. 


\
\
 \
\
\
\
\
\f

HONDA (1991-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - HONDA (1991-98)\
\
\
\
\
\

Model Year (1) Location
Accord ............... 1993-98 ..................... D/P
1991-92 ...................... DS
Civic ................ 1994-98 ..................... D/P
1992-93 ...................... DS
Civic del Sol ........ 1994-97 ..................... D/P
1993 ........................ DS
CR-V ................. 1997-98 ..................... D/P
Odyssey .............. 1995-98 ..................... D/P
Prelude .............. 1994-98 ..................... D/P
SI 4WS ............. 1992-93 ..................... D/P
Except SI 4WS ...... 1992-93 ...................... DS
Passport ........... 1995 1/2-98 ................... D/P
( 1) - Location Definitions: D/P = Driver's & Passenger's
Side, DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\

INSPECTION PROCEDURES

Page 1008 of 1501

INSPECTION PROCEDURES TABLE - HONDA (1991-98 EXCEPT PASSPORT)\
\
\
\
\
\
\
 
Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* Seat Belt Tensioners (If Equipped) 


* SRS Control Unit 

\
\
\b\
\
\
\
\


Inspect & If 
* Cable Reel 

Damaged, Replace 
* Dash Sensors (1991-94) 

Component 
* Seat Belts 

(Even If Air 
* SRS Control Unit 

Bag Did Not 
* Wiring Harness 

Deploy)  

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 


* DO NOT attempt SRS wiring repairs. If SRS 

 wiring or harness connectors are faulty, 

 replace faulty wiring harness. 


* After vehicle is repaired, ensure AIR BAG 

 warning light is functioning properly. 


\
\
 \
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - HONDA (1995 1/2-98 PASSPORT)\
\
\
\
\
\
\



Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* Sensing & Diagnostic Module (SDM) 

\
\
\b\
\
\
\
\


Inspect & If 
* Instrument Panel Braces 

Damaged, Replace 
* Instrument Panel Steering Column 

Component  Reinforcement Plate 

(Even If Air 
* Seat Belts & Mounting Points 

Bag Did Not 
* Knee Bolsters & Mounting Points 

Deploy) 
* Steering Column 


* SRS Coil Assembly 


* Wiring Harnesses 

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 


* DO NOT attempt wiring harness repairs. 

 Replace harness. 


\
\
 \
\
\
\
\
\f

HYUNDAI (1994-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - HYUNDAI (1994-98)\
\
\
\
\
\

Model Year (1) Location
Accent ............... 1995-98 ..................... D/P
Elantra .............. 1996-98 ..................... D/P
1994-95 ...................... DS
Sonata ............... 1995-98 ..................... D/P
Tiburon .............. 1997-98 ..................... D/P
( 1) - Location Definitions: D/P = Driver's & Passenger's
Side, DS = Driver's Side Only, SI = Side Impact.

Page 1010 of 1501

  * Side Air Bag Module ( 1) 

\
\
\b\
\
\
\
\


Inspect & If 
* Center Pillar Inner ( 1) 

Damaged, Replace 
* Instrument Panel 

Component 
* Seat ( 1) 

(Even If Air 
* Seat Belt Pretensioners ( 2) 

Bag Did Not 
* Spiral Cable 

Deploy) 
* Steering Wheel 


* Wiring Harnesses 

\
\
\b\
\
\
\
\


Comments 
* Inspect all SRS components for dents, 

 deformities or rust. 


* After repairs are completed, check AIR BAG 

 warning light to ensure system is functioning

 properly. 

\
\
 \
\
\
\
\


(
1) - On side of impact. 

(
2) - Except I30 and QX4. 


\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - INFINITI-2\
\
\
\
\
\
\
 

Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* Control Unit, Diagnosis 


* Instrument Panel 


* Seat Belt Pretensioners ( 1) 

\
\
\b\
\
\
\
\


Inspect & If 
* All Sensors ( 2) 

Damaged, Replace 
* Spiral Cable 

Component 
* Steering Wheel 

(Even If Air 
* Wiring Harnesses 

Bag Did Not  

Deploy)  

\
\
\b\
\
\
\
\


Comments 
* Inspect all SRS components for dents, 

 deformities or rust. 


* After repairs are completed, check AIR BAG 

 warning light to ensure system is functioning

 properly. 

\
\
 \
\
\
\
\


(
1) - Except I30. 

(
2) - Except 1996 I30, 1995-96 J30 and 1995-96 Q45. 


\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - INFINITI-3\
\
\
\
\
\
\



Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* Control Unit, Diagnosis 


* Sensors In Affected Collision Area 

\
\
\b\
\
\
\
\


Inspect & If 
* All Sensors 

Damaged, Replace 
* Spiral Cable 

Component 
* Steering Wheel 

(Even If Air 
* Wiring Harnesses 

Bag Did Not  

Deploy)  

\
\
\b\
\
\
\
\


Comments 
* Inspect all SRS components for dents, 

 deformities or rust. 

Page 1011 of 1501

  * After repairs are completed, check AIR BAG 

 warning light to ensure system is functioning

 properly. 


\
\
 \
\
\
\
\
\f

ISUZU (1990-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - ISUZU (1990-98)\
\
\
\
\
\
\

Model Year (1) Location Inspection Table
Hombre ....... 1996-97 ........... DS .................. ISUZU-1
Impulse ...... 1990-92 ........... DS .................. ISUZU-5
Oasis ........ 1996-98 .......... D/P .................. ISUZU-2
Rodeo ........ 1996-98 .......... D/P .................. ISUZU-3
1995 1/2 ......... D/P .................. ISUZU-3
Stylus ....... 1991-93 ........... DS .................. ISUZU-5
Trooper ...... 1996-98 .......... D/P .................. ISUZU-3
1995 ............ D/P .................. ISUZU-4
( 1) - Location Definitions: D/P = Driver's & Passenger's Side,
DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\
\

INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - ISUZU-1\
\
\
\
\
\
\
 
Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* Sensors In Area Of Accident Damage 

\
\
\b\
\
\
\
\


Inspect & If 
* Instrument Panel Braces 

Damaged, Replace 
* Instrument Panel Steering Column 

Component  Reinforcement Plate 

(Even If Air 
* Seat Belts & Mounting Points 

Bag Did Not 
* Knee Bolster 

Deploy) 
* Sensors In Area Of Accident Damage 


* SRS Coil Assembly 

\
\
\b\
\
\
\
\


Comments 
* Any sensor which the Diagnostic Energy 

 Reserve Module (DERM) indicates as bad must 

 be replaced. 


* If any components are damaged or bent, they 

 must be replaced. 


* SRS wiring can be repaired following 

 manufacturer's instructions. 


\
\
 \
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ISUZU-2\
\
\
\
\
\
\



Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* Seat Belt Tensioners (If Equipped) 


* SRS Control Unit 

\
\
\b\
\
\
\
\


Inspect & If 
* Cable Reel 

Damaged, Replace 
* Dash Sensors (1991-94) 

Page 1012 of 1501

 Component  * Seat Belts 

(Even If Air 
* SRS Control Unit 

Bag Did Not 
* Wiring Harness 

Deploy)  

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 


* DO NOT attempt SRS wiring repairs. If SRS 

 wiring or harness connectors are faulty, 

 replace faulty wiring harness. 


* After vehicle is repaired, ensure AIR BAG 

 warning light is functioning properly. 


\
\
 \
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ISUZU-3\
\
\
\
\
\
\
 

Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* Sensing & Diagnostic Module (SDM) 

\
\
\b\
\
\
\
\


Inspect & If 
* Instrument Panel Braces 

Damaged, Replace 
* Instrument Panel Steering Column 

Component  Reinforcement Plate 

(Even If Air 
* Seat Belts & Mounting Points 

Bag Did Not 
* Knee Bolsters & Mounting Points 

Deploy) 
* Steering Column 


* SRS Coil Assembly 


* Wiring Harnesses 

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 


* DO NOT attempt wiring harness repairs. 

 Replace harness. 


\
\
 \
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ISUZU-4\
\
\
\
\
\
\



Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment 
* All Sensors 

\
\
\b\
\
\
\
\


Inspect & If 
* SRS Coil Assembly 

Damaged, Replace 
* Instrument Panel Steering Column 

Component  Reinforcement Panel 

(Even If Air 
* Instrument Panel Braces 

Bag Did Not 
* Knee Bolsters 

Deploy) 
* Seat Belts Mounting Points 


* Sensors In Area of Accident Damage 


* Steering Column 

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 


* DO NOT attempt wiring harness repairs. 

 Replace harness. 


\
\
 \
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ISUZU-5\
\
\
\
\
\
\



Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module 

Page 1013 of 1501

 Deployment  

\
\
\b\
\
\
\
\


Inspect & If 
* Arming Sensor 

Damaged, Replace 
* Coil Assembly 

Component 
* Diagnostic Energy Reserve Module (DERM) 

(Even If Air 
* Forward Sensor 

Bag Did Not 
* Instrument Panel-To-Steering Column 

Deploy)  Reinforcement 


* Knee Pad 


* Passenger Compartment Sensor 


* Steering Column 


* Wiring Harness & Brackets 

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 


\
\
 \
\
\
\
\
\f

KIA (1995-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - KIA (1995-98)\
\
\
\
\
\

Model Year (1) Location
Sephia .............. 1996-98 ...................... D/P
1995 1/2 ..................... D/P
Sportage ............ 1996-98 ...................... D/P
( 1) - Location Definitions: D/P = Driver's & Passenger's
Side, DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\

INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - KIA (1995-98)\
\
\
\
\
\
\
 
Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air Bag Module(s) 

Deployment  

\
\
\b\
\
\
\
\


Inspect & If 
* Air Bag Diagnosis Control Unit 

Damaged, Replace 
* Clockspring 

Component 
* Impact Sensors Sensor Mountings ( 1) 

(Even If Air 
* Steering Column 

Bag Did Not 
* Steering Wheel 

Deploy) 
* Wiring Harness 

\
\
\b\
\
\
\
\


Comments 
* After repairs a completed, ensure Warning 

 Light is functioning properly. 

\
\
 \
\
\
\
\


(
1) - 1995 1/2 Sephia only. 


\
\
\
\
\
\
\
\f

LEXUS (1990-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - LEXUS (1990-98)\
\
\
\
\
\
\


Page 1023 of 1501

\
\
\b\
\
\
\
\


Comments 
* DO NOT attempt SRS wiring repairs. 


* If any components are damaged or bent, they 

 must be replaced. 

\
\
 \
\
\
\
\


(
1) - If Equipped. 

(
2) - 1998 Legacy, on side of deployment. 


\
\
\
\
\
\
\
\f

SUZUKI (1995-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - SUZUKI (1995-98)\
\
\
\
\
\

Model Year (1) Location
Esteem .............. 1995-98 ...................... D/P
Sidekick ............ 1996-98 ...................... D/P
Swift ............... 1995-98 ...................... D/P
X90 ................. 1996-98 ...................... D/P
( 1) - Location Definitions: D/P = Driver's & Passenger's
Side, DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\

INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - SUZUKI (1995-98)\
\
\
\
\
\
\
 
Action  Component or System 

\
\
\b\
\
\
\
\


Replace After 
* Air BagModule(s) 

Deployment 
* Sensing & Diagnostic Module (SDM) 

\
\
\b\
\
\
\
\


Inspect & If 
* Air Bag Warning Light 

Damaged, Replace 
* Combination Switch Assembly 

Component 
* Contact Coil 

(Even If Air 
* Forward Discriminating Sensor ( 1) 

Bag Did Not 
* Instrument Panel Reinforcement 

Deploy) 
* Knee Bolsters 


* Seat Belts & Mounting Points 


* SDM Bracket 


* Steering Column Bracket 


* Steering Column & Shaft Joints 


* Steering Wheel 


* Wiring Harness 

\
\
\b\
\
\
\
\


Comments 
* If any components are damaged or bent, they 

 must be replaced. 

\
\
 \
\
\
\
\


(
1) - Swift Only 


\
\
\
\
\
\
\
\f

TOYOTA (1990-98)

Page 1105 of 1501

STEERING COLUMN SWITCHES
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Steering Column Switches
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
* PLEASE READ THIS FIRST *
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. DO NOT
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
DESCRIPTION
Headlight and turn signal switch and wiper/washer switch are
part of combination switch. For information on cruise control switch
(right side of column), see appropriate CRUISE CONTROL SYSTEMS
article.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE\
\
\
\
\
\

Component Location
Headlight Relay .................... In Engine Compartment
Fuse/Relay Block
Foglight Relay
Except Montero & Montero Sport ... In Engine Compartment
Fuse/Relay Block
Taillight Relay
Except Montero Sport ............. In Engine Compartment
Fuse/Relay Block
Turn Signal/Hazard Flasher Unit
Diamante ............................ At Left Kick Panel
Eclipse .......................... Behind Center Of Dash
Except Diamante & Eclipse ..... Behind Left Side Of Dash
Wiper Relay
Front
Except Diamante & 3000GT .......... On Steering Column
Rear
Eclipse ........................ Behind Center Of Dash
Montero & Montero Sport .............. On Relay Block,
Behind Left Side Of Dash
3000GT ................ Behind Left Rear Quarter Panel
\
\
\
\
\
\

COMPONENT TESTS
DIAMANTE
Turn Signal, Lighting & Dimmer/Passing Switch Tests
Disconnect steering column combination switch connector. See
Fig. 1 . Check continuity between specified terminals. See
STEERING COLUMN COMBINATION SWITCH CONTINUITY CHECK TABLE (DIAMANTE) .

Page:   < prev 1-10 11-20 21-30 31-40 41-50 next >