fluid MITSUBISHI MONTERO 1998 Service Manual

ABBREVIATIONS
1998 Mitsubishi Montero
GENERAL INFORMATION
COMMONLY USED ABBREVIATION
"A" ABBREVIATION TABLE
"A" ABBREVIATION TABLE







\









\








\









\









\









\









\






 
ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






A Amperes 

A/C Air Conditioning 

A/T Automatic Transmission/Transaxle 

AAP Auxiliary Accelerator Pump 

AB Air Bleed 

ABCV Air Bleed Control Valve 

ABDC After Bottom Dead Center 

ABRS Air Bag Restraint System 

ABS Anti-Lock Brake System 

AC Alternating Current 

ACC A/C Clutch Compressor 

ACCS A/C Cycling Switch 

ACCUM Accumulator 

ACCY Accessory 

ACT Air Charge Temperature Sensor 

ACV Thermactor Air Control Valve 

ADJ Adjust or Adjustable 

ADV Advance 

AFS Airflow Sensor 

AI Air Injection 

AIR or A.I.R. Air Injection Reactor 

AIS Air Injection System 

ALCL Assembly Line Communications Link 

ALDL Assembly Line Diagnostic Link 

ARC Automatic Ride Control 

ASCD Automatic Speed Control Device 

ASCS Air Suction Control Solenoid 

ASD Auto Shutdown 

ASDM Air Bag System Diagnostic Module 

ASV Air Suction Valve 

ATC Automatic Temperature Control 

ATDC After Top Dead Center 

ATF Automatic Transmission Fluid 

ATS Air Temperature Sensor 

AXOD Automatic Transaxle Overdrive 

Abs. Absolute 

Accy. Accessory 

Alt. Alternator or Altitude 

Amp. Ampere 

Assy. Assembly 

Auto. Automatic 

Aux. Auxiliary 

Avg. Average 











\








\









\









\









\









\









\





\f

"B" ABBREVIATION TABLE
"B" ABBREVIATION TABLE

ANTI-LOCK BRAKE SAFETY PRECAUTIONS
1998 Mitsubishi Montero
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85C for 2 hours is generally considered a
maximum limit).

ANTI-LOCK BRAKE SYSTEM
1998 Mitsubishi Montero
1997-98 BRAKES
Mitsubishi - Anti-Lock
Montero
DESCRIPTION
CAUTION: See ANTI-LOCK BRAKE SAFETY PRECAUTIONS article in GENERAL
INFORMATION.
NOTE: For more information on brake system, see BRAKE SYSTEM
article.
The Anti-Lock Brake System (ABS) is designed to prevent wheel\
lock-up during heavy braking. This allows operator to maintain
steering control while stopping vehicle in shortest distance possible.
Major components are a hydraulic unit, wheel speed sensors, "G"
sensor, ABS Electronic Control Unit (ECU) and ANTI-LOCK warning light.\
ABS has a self-diagnostic system to indicate a system malfunction and
for use in system trouble shooting.
OPERATION
Each wheel sensor sends an AC electrical signal to the ECU.
The ECU reads this information as wheel speed. When any decelerating
wheel speed rate is determined to be excessive in comparison to other
monitored wheels, the hydraulic unit cycles hydraulic brake pressure
to each wheel to equalize speed of all wheels. ABS turns itself off
when vehicle drops to 4 MPH. Minor lock-up may occur at this point.
With engine running and vehicle speed greater than 4 MPH,
pump motor will operate for a short period of time and may be heard
inside vehicle. During pump motor operation, ABS system is completing
a self-check. During ABS system operation, a pulsing brake pedal and
vibration in steering wheel and vehicle body may be experienced. These
conditions are normal.
BLEEDING BRAKE SYSTEM
BLEEDING PROCEDURES
CAUTION: When adding brake fluid, ensure filter is properly fitted on
reservoir tank.
ABS system is bled using conventional method. With engine
running, manually bleed system using an assistant. For bleeding order,
see BRAKE LINE BLEEDING SEQUENCE table. Ensure Load Sensing
Proportioning Valve (LSPV) is bled in sequence. Remove all air from
brake system. Refill brake fluid reservoir after bleeding procedure is
complete.
BRAKE LINE BLEEDING SEQUENCE









\









\









\









\









\









\









\







Application Sequence
Montero ....................................... RR, LR, LSPV, RF, LF









\









\









\









\









\









\









\

Fig. 4: Checking Operation Of Shift Solenoids No. 1 & No. 2
Courtesy of Mitsubishi Motor Sales of America.
SELF-DIAGNOSTIC SYSTEM
SYSTEM DIAGNOSIS
NOTE: Before testing transmission, ensure fluid level is correct
and throttle and shift cables are properly adjusted. Ensure
engine starts with shift lever in Park and Neutral to ensure
proper adjustment of park/neutral position switch.
Transmission must first be tested by checking for stored
codes. See RETRIEVING DIAGNOSTIC TROUBLE CODES (DTC).
TCM monitors transmission operation and contains a self-
diagnostic system which stores a DTC if an electronic control system
failure or problem exists. If a problem exists in any of the solenoids
or speed sensors and a DTC is set, TCM delivers a signal to blink the
ATF TEMP light on instrument panel to warn the driver. DTC may be set
if a failure exists and can be retrieved for transmission diagnosis.
RETRIEVING DIAGNOSTIC TROUBLE CODES (DTC)
NOTE: Before retrieving DTC, ensure proper battery voltage exists
for proper self-diagnosis system operation. DO NOT disconnect
battery or ECM connectors before retrieving DTC.
Retrieving Codes Using Scan Tool
Ensure ignition switch is in OFF position. Connect scan tool
to Data Link Connector (DLC). See Fig. 5. Turn ignition switch to ON
position. Check for stored DTC and record code(s). See DIAGNOSTIC
TROUBLE CODE IDENTIFICATION table.

If DTC 51 is set also, go to DTC 51: 1ST GEAR RATIO SIGNAL
INCORRECT test. If DTC 51 is not set, check overdrive brake for a
mechanical failure. See OVERDRIVE BRAKE in MITSUBISHI R4AW3 & V4AW3
OVERHAUL article.
SYMPTOM TROUBLE SHOOTING
NOTE: Check system using appropriate scan tool. See WIRING DIAGRAMS
for electrical schematics and COMPONENT TESTING.
COMMUNICATION WITH SCAN TOOL NOT POSSIBLE
If scan tool cannot communicate with TCM, check proper
connection with DLC. Check TCM power circuits, TCM ground circuits and
malfunctioning TCM.
SHIFT POINTS INCORRECT
If shift points are incorrect, check for DTCs. If no DTC is
present, check oil temperature sensor, pattern select switch, 4WD low
range detection switch and TCM for proper operation.
UPSHIFTS OCCUR SPONTANEOUSLY
If upshifting occurs spontaneously, check park/neutral
position switch, overdrive switch and TCM for proper operation.
TCC LOCK-UP MALFUNCTIONING
If TCC lock-up system is not operating properly, check torque
converter, valve body, lock-up switch and oil temperature switch.
COMPONENT TESTING
A/T FLUID TEMPERATURE SWITCH
1) Remove fluid temperature switch, located to rear of
neutral safety switch. Immerse switch in container of ATF up to top
threaded portion of switch. Using a DVOM, check continuity between
switch terminals. Continuity should not exist when fluid temperature
is 257
F (125C) or less.
2) When fluid is heated to 289-304F (143-151C), continuity
should exist. Replace switch if necessary. Apply thread sealant to
fluid temperature switch threads and install in transmission.
BRAKELIGHT SWITCH
1) Disconnect electrical connector from brakelight switch,
located near brake pedal. Using ohmmeter, ensure continuity exists
between terminal No. 2 (White/Red wire) and terminal No. 3 (Green
wire) with brake pedal released. Replace brakelight switch if
continuity does not exist. Continuity should not exist between
terminals No. 2 and No. 3 with brake pedal depressed.
2) If continuity does not exist, ensure brake pedal is
properly adjusted so brakelight switch has proper travel for switch
operation. If proper brakelight switch travel exists, replace
brakelight switch.
ENGINE COOLANT TEMPERATURE (ECT) SENSOR

* BRAKE SYSTEM UNIFORM INSPECTION GUIDELINES *
1998 Mitsubishi Montero
GENERAL INFORMATION
Brake Systems - Motorist Assurance Program
Standards For Automotive Repair
All Makes & Models
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCUMULATORS
ANCHOR PINS
ANTI-LOCK BRAKE SYSTEMS
BACKING PLATES
BRAKE FLUID
BRAKE FRICTION MATERIAL
BRAKE PADS
BRAKE PEDALS
BRAKE SHOES
BRAKE SHOE HARDWARE
BRAKE STOPLIGHT SWITCHES
BULB SOCKETS
BULBS AND LEDS
CALIPER HARDWARE
CALIPERS
CONTROLLERS
DIGITAL RATIO AXLE CONTROLLERS AND BUFFERS (DRAC AND DRAB)
DISABLE SWITCHES
DRUMS
ELECTRICAL PUMPS AND MOTORS
ELECTRONIC CONTROLLERS
FLUID
FLUID LEVEL SENSOR SWITCHES
FOUR WHEEL DRIVE SWITCHES
FRICTION MATERIAL
G SENSORS
HOSES
HYDRAULIC MODULATORS
HYDRO-BOOSTERS
HYDRO-ELECTRIC BOOSTERS (POWERMASTER)
IGNITION DISABLE SWITCHES
LATERAL ACCELERATION SWITCHES
LEDS
LENSES
MASTER CYLINDERS
MODULATORS
MOTORS
PARKING BRAKE SWITCHES
PARKING BRAKE SYSTEMS
PADS
PEDAL TRAVEL SWITCHES
PEDALS
POWERMASTER
PUMPS
PRESSURE DIFFERENTIAL SWITCHES
PRESSURE SWITCHES
RELAYS
ROTORS
SELF-ADJUSTING SYSTEMS

NOTE: Electro-magnetic interference (EMI) may be caused by
incorrect installation of accessories or components. EMI can
result in improper system operation.
BACKING PLATES
BACKING PLATE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Anchor pin bent ......... B .. Require repair or replacement.
Anchor pin broken ....... A ............ Require replacement.
Anchor pin worn, affecting
structural integrity ... B ............ Require replacement.
Backing plate bent ...... B .. Require repair or replacement.
Backing plate broken .... A ............ Require replacement.
Backing plate cracked ... B .. Require repair or replacement.
Corroded, affecting
structural integrity .... A ............ Require replacement.
Loose ................... B .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Shoe lands worn ......... A .. Require repair or replacement.









\









\









\









\









\









\









\


BRAKE FLUID
CAUTION: Most manufacturers prohibit the use of DOT 5 brake fluid
in a system equipped with ABS.
DOT 3, DOT 4, and DOT 5.1 brake fluids are clear or light
amber in color. DOT 5 brake fluid is violet in color. Correct fluid
required for the brake system is stamped on the master cylinder cover.
BRAKE FLUID INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Beyond service interval . 3 .. Suggest flushing and refilling
with correct fluid.
Brake fluid type
incorrect .............. B .. Require flushing and refilling
with correct fluid.
Contaminated, for example,
fluid other than brake
fluid present .......... A or B ....... ( 1) Require service.
Hydraulic component ..... 3 .. Suggest flushing and refilling
overhaul or replacement with correct fluid.
Rubber master cylinder
cover gasket distorted
and gummy .............. A .......... ( 2) Require replacement
of gasket.
( 1) - If a fluid other than brake fluid is present in the brake
system which DOES affect the rubber parts, the required
service is to:
* Remove all components having rubber parts from the
system.
* Flush lines with denatured alcohol or brake cleaner
* Repair or replace all components having rubber parts
* Flush and fill with correct brake fluid. (Code A)
If a fluid other than brake fluid is present in the brake

system which DOES NOT affect the rubber parts, the required
service is to flush and fill with the correct brake fluid.
(Code B)
( 2) - This condition may indicate contaminated brake fluid.









\









\









\









\









\









\









\


BRAKE FRICTION MATERIAL
See FRICTION MATERIAL .
BRAKE PADS
See FRICTION MATERIAL .
BRAKE PEDALS
BRAKE PEDAL INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Bent, affecting
performance ............ A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Pedal pad missing ....... C .... Require replacement of pedal
pad.
Pedal pad worn .......... 1 ............ Suggest replacement.
Pivot bushings worn,
affecting performance .. A .... Require replacement of pivot
bushings.









\









\









\









\









\









\









\


BRAKE SHOES
See FRICTION MATERIAL .
BRAKE SHOE HARDWARE
See also SELF-ADJUSTING SYSTEMS .
BRAKE SHOE HARDWARE INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Broken .................. A ............ Require replacement.
Distorted ............... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Surfaces rust-pitted .... 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.









\









\









\









\









\









\









\


BRAKE STOPLIGHT SWITCHES
BRAKE STOPLIGHT INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.

hardware.
Attaching hardware threads
damaged ................ A ... Require repair or replacement
of hardware.
Attaching hardware threads
stripped (threads
missing) ............... A ... Require repair or replacement
of hardware.
Code set (if
applicable) ............ A .......... (1) Further inspection
required.
Connector broken ........ A .. Require repair or replacement.
Connector melted ........ A ........... ( 2) Require repair or
replacement.
Connector missing ....... A ................. Require repair.
Contaminated ............ A .. Require repair or replacement.
Inoperative ............. B .. Require repair or replacement.
( 3) Further inspection required.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 2) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Refer to manufacturer's diagnostic trouble code procedure
and require repair or replacement of affected component(s).
( 2) - Determine cause and correct prior to repair or replacement
of part.
( 3) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable. Check
for accepted cleaning procedure.









\









\









\









\









\









\









\


FLUID
See BRAKE FLUID.
FLUID LEVEL SENSOR SWITCHES
See SWITCHES.
FOUR WHEEL DRIVE SWITCHES
See SWITCHES.

FRICTION MATERIAL
NOTE: Original Equipment Manufacturer (OEM) specifications
designate replacement at different thicknesses.
CAUTION: It is required that friction material be matched in axle
sets for consistent braking characteristics.
FRICTION MATERIAL INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Contaminated, for example,
fluid that leaked from
caliper, wheel cylinder,
or axle seal ........... A ........ ( 1) Require replacement.
Cracked through ......... B Require replacement.
Flaking or chunking ..... B Require replacement.
Glazed (shiny) .......... .. ........ No service suggested or
required.
Grooves or ridges ....... .. .... ( 2) No service suggested or
required.
Permanently attached
hardware bent .......... A ............ Require replacement.
Permanently attached
hardware broken ........ A ............ Require replacement.
Permanently attached
hardware loose ......... A ............ Require replacement.
Permanently attached
hardware missing ....... C ............ Require replacement.
Permanently attached
hardware seized ........ A .. Require repair or replacement.
Rivets loose ............ B ............ Require replacement.
Separating from backing . B ............ Require replacement.
Shoe table or web bent .. B ............ Require replacement.
Shoe table or web
cracked ................ A ............ Require replacement.
Shoe table or web worn,
affecting performance .. A ............ Require replacement.
Surface cracking ........ .. ........ No service suggested or
required. Further inspection
may be necessary to determine
cause.
Tapered wear ............ B ........ ( 3) Suggest replacement.
Thickness of one pad is
greater than opposite pad
in the same caliper
(uneven wear) .......... .. .... ( 4) Replacement of friction
material not suggested or
required. Further inspection
required. See CALIPERS
and CALIPER HARDWARE.
Wear indicator device
(electronic) contacts
rotor .................. B ...... ( 5) Require replacement of
appropriate parts.
Wear indicator device
(mechanical) bent ....... .. .......... ( 6) Further inspection
required.
Wear indicator device
(mechanical) broken .... .. ......... ( 6) Further inspection
required.