MITSUBISHI OUTLANDER SPORT 2013 3.G Owners Manual

7-60 Vehicle care and maintenance
7
5. To install the bulb, perform the removal steps in reverse.
Daytime running lights
(if so equipped)
N00902000061
1. Insert a straight blade (or minus) screwdriver with a clothover its tip info the light cover (A) and pry gently to
remove it.
CAUTION
!
Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen light bulb with a bare hand,
dirty glove, etc. The oil from your hand could cause
the bulb to break the next time the fog lights are
used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0150700US.book 60 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-61
7
2. Remove the screws (B) and remove the light unit. 3. Turn the bulb (C) counterclockwise to remove it.
BK0150700US.book 61 ページ ２０１２年３月２２日　木曜日　午後６時４６分

7-62 Vehicle care and maintenance
7
4. While holding down the tab (D), pull out the socket (E).
5. To install the bulb, perform the removal steps in reverse.
Rear combination lights
N00943700458
1. Remove the screws (A) that hold the light unit and removethe light unit.
BK0150700US.book 62 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-63
7
2. Turn the socket and bulb assembly counterclockwise toremove it.NOTE
The rear side-marker light, and the tail and stop light uses
an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced. 3. Pull the bulb out of the socket.B- Rear side-marker light, and tail and stop light (LED)
- cannot be replaced
C- Rear turn signal light
BK0150700US.book 63 ページ ２０１２年３月２２日　木曜日　午後６時４６分

7-64 Vehicle care and maintenance
7
4. To install the bulb, perform the removal steps in reverse.NOTE
When mounting the light unit, align the groove (D) on the
light unit with the clip on the body and the pin (E) on the
unit with the hole in the body.
Back-up lights
N00929100054
1. Open the liftgate.
2. Insert a screwdriver into the notch of the cover and pry
gently to remove the cover.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the cover.
BK0150700US.book 64 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-65
7
3. Turn the socket counterclockwise to remove it. 4. Pull the bulb out of the socket.
BK0150700US.book 65 ページ ２０１２年３月２２日　木曜日　午後６時４６分

7-66 Vehicle care and maintenance
7
5. To install the bulb, perform the removal steps in reverse.NOTE
When installing the lid, align the tab on the lid with the
hole on the vehicle side.
License plate lights
N00944000386
1. When removing the light unit (A), push it toward the left
side of the vehicle body.
BK0150700US.book 66 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-67
7
2. Remove the socket (B) and bulb assembly by turning itcounterclockwise. 3. Pull the bulb out of the socket.
BK0150700US.book 67 ページ
２０１２年３月２２日　木曜日　午後６時４６分

7-68 Vehicle care and maintenance
7
4. To install the bulb, perform the removal steps in reverse.NOTE
When mounting the light unit, insert tab (C) first then
align tab (D) with its hole.
High-mounted stop light
N00943900102
NOTE
The high-mounted stop light uses an LED instead of the
bulb. Check with an authorized Mitsubishi Motors dealer
or a repair facility of your choice when the light needs to
be repaired or replaced.
BK0150700US.book 68 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Vehicle care and maintenance7-69
7
Vehicle care precautions
N00945100166
In order to maintain the value of your vehicle, perform regular
maintenance using the proper materials and procedures. Be
sure to use only those materials and procedures that meet your
local environmental pollution control regulations. Choose the
materials you will use carefully, to be sure that they do not con-
tain corrosives. If you are not sure, contact an authorized
Mitsubishi Motors dealer for help in choosing these materials.
These can all be dangerous, and they all can damage your vehi-
cle.
CAUTION
!

Cleaning products can be dangerous. Some are poi-
sonous and others are highly flammable. Some are
dangerous if you breathe their fumes in a closed
space. When you use anything in a container to
clean your vehicle, be sure to follow the instructions.
Always open your vehicle doors or windows when
you’re cleaning the inside. Never use the following
chemicals to clean your vehicle:
• Gasoline
• Carbon Tetrachloride
• Benzine
• Kerosene
• Naphtha
• Acetone
• Turpentine
• Paint Thinner
• Lacquer Thinner
• Nail Polish Remover
BK0150700US.book 69 ページ ２０１２年３月２２日　木曜日　午後６時４６分