NISSAN 350Z 2007 Z33 Body, Lock And Security System Workshop Manual

BODY REPAIR
BL-181
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
ANTI-CORROSIVE WAX
To improve corrosion resistance, anti-corrosive wax is applied inside the body sill and inside other closed sec-
tions. Accordingly, when replacing these parts, be sure to apply anti-corrosive wax to the appropriate areas of
the new parts. Select an excellent anti-corrosive wax which will penetrate after application and has a long shelf
life.
SIIA1979E

BL-182
BODY REPAIR
Revision: 2006 November2007 350Z
UNDERCOATING
The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoat-
ing which is rust preventive, soundproof, vibration-proof, shock-resistant, adhesive, and durable.
Precautions in undercoating
1. Do not apply undercoating to any place unless specified (such as the areas above the muffler and three
way catalyst which are subjected to heat).
2. Do not undercoat the exhaust pipe or other parts which become hot.
3. Do not undercoat rotating parts.
4. Apply bitumen wax after applying undercoating.
5. After putting seal on the vehicle, put undercoating on it.
SIIA2298E

BODY REPAIR
BL-183
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
STONE GUARD COAT
To prevent damage caused by stones, the lower outer body panel (fender, door, etc.) have an additional layer
of Stone Guard Coating over the ED primer coating. When replacing or repairing these panels, apply Stone
Guard coating to the same portions as before. Use a coating which is rust preventive, durable, shock-resistant
and has a long shelf life.
SIIA2299E

BL-184
BODY REPAIR
Revision: 2006 November2007 350Z
Body Sealing (Coupe)NIS0003Y
DESCRIPTION
The following figure shows the areas which are sealed at the factory. Sealant which has been applied to these
areas should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of
sealant and not to allow other unaffected parts to come into contact with the sealant.
SIIA1976E

BODY REPAIR
BL-185
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
SIIA1977E

BL-186
BODY REPAIR
Revision: 2006 November2007 350Z
SIIA1978E

BODY REPAIR
BL-187
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
SIIA2335E

BL-188
BODY REPAIR
Revision: 2006 November2007 350Z
Body Sealing (Roadster)NIS0003Z
DESCRIPTION
The following figure shows the areas which are sealed at the factory. Sealant which has been applied to these
areas should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of
sealant and not to allow other unaffected parts to come into contact with the sealant.
SIIA2300E

BODY REPAIR
BL-189
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
SIIA2301E

BL-190
BODY REPAIR
Revision: 2006 November2007 350Z
SIIA2302E