sensor NISSAN ALMERA N15 1995 Service Manual

GA16DE forAustralia TROUBLE
DIAGNOSIS FOROTC41 ~
Intake AirTemperature Sensor(IATS)(Cont'd)

EC-IATS-01

t
INTAKE
AIR
TEMPERATURE
SENSOR

~

-:Detectable line

for
DTC

-: Non-detectable

line for
DTC
•

~

@
GY
R/Y

~
TA
B

15"0
I

GND
-A
ECM
(ECCSCONTROL
MODULE)

em

101 102
103
107 108
109
113 114
115 104
105 106
110 111112
116
117
118

EC-125 HEC073

Checkthefollowing.
• Harness continuity
between ECMand
intake airtemperature
sensor
If NG, repair harness or
connectors.

NG

INSPECTION
START

CHECK POWER SUPPLY.

1. Turn ignition switch"OFF".
2. Disconnect intakeairtemperature
sensor harness connector.
3. Turn ignition switch"ON".
4. Check voltage between terminal @
and ground.

Voltage: Approximately SV
TROUBLE
DIAGNOSIS FORDTC41
rnJ

Intake AirTemperature Sensor(IATS)(Cont'd)
DIAGNOSTIC PROCEDURE

--

~
Intake airtemperature
'" '\ sensor harness connector
AEC550

~ DISCONNECT
ciili
10

AEC723

~i5 ~

dID
CHECK
GROUND CIRCUIT.

1. Turn ignition switch"OFF".
2. Check harness continuity between
terminal
G)
and engine ground.

Continuity shouldexist.
OK

CHECK COMPONENT
(Intake airtemperature sensor).
Refer to"COMPONENT INSPECTION"
on next page.
NG
NG
Check
thefollowing.
• Harness continuity
between ECMand
intake airtemperature
sensor
If NG, repair harness or
connectors
Replace intakeairtem-
perature sensor.

OK

Disconnect andreconnect harnesscon-

AEC724
nectorsinthe circuit. Thenretest.
Trouble isnot fixed.
Check ECMpinterminals fordamage
or the connection ofECM harness con-
nector.
Reconnect ECMharness connector and
retest.
INSPECTION END

EC-126

TROUBLEDIAGNOSIS FORDTC41 @K]
Intake AirTemperature Sensor(IATS)(Cont'd)
COMPONENT INSPECTION

20
19
6
9
4

fl 2

ffi
10

iii
0.8

'w

&
04

0.2
0.1 -20 020 40 60 80100
(-4) (32) (68)(104)(140)(176)(212)
Temperature
'c
(OF)

SEF012PIntake
airtemperature sensor

Check resistance asshown inthe figure.
Intake airtemperature
'c ('F)

20 (68)
50 (122)
EC-127
Resistance
kQ

2.1 -2.9
0.68 -1.0
•

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS
Throttle Position Sensor

The throttle position sensorresponds tothe accelerator pedal
movement. Thissensor isakind ofpotentiometer whichtrans-
forms thethrottle position intooutput voltage, andemits the
voltage signaltothe ECM. Inaddition, thesensor detects the
opening andclosing speedofthe throttle valveandfeeds the
voltage signaltothe ECM.
Idle position ofthe throttle valveisdetermined
by
the ECM
receiving thesignal fromthethrottle position sensor.Thisone
controls engineoperation suchasfuel cut.

SEF089K

CIl
Supplyvoltage:

r
-i.~h __
~3_
i
45
I
'V ,Appl.' b....
ffi
t~miMI,
No1,,'
31

~_ =r--=-tfr ~
I

l ~
1
N~
I

Throttle position sensor g
-g

'5 ::: 0.5

0-

'5
0 0----- -_.- --------_.

OZ 0 90

Throttle valveopening angle(deg_)
EC-128 SEF520Q

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS~
Throttle Position Sensor(Cont'd)

EC-TPS-01

f
1

I I

I

t
I
JJ

I

I
I

I

I

I

I
THROTTLE
POSITION
SENSOR

@
@:

ForEurope andIsrae 1
_: Detectable line
for DTC
-: Non-detectable
line forDTC

•

ECM (ECCS
CONTROL
MODULE)

em

B

12"g
I

GND
-A
JOINT
CONNECTOR-6

@

I:
.-.----...f~:==:P:JI--- ..

P!L YB

~~um

AVCC TVOGND
-A

t

JXL@

<I@TI)
BR
_
.. ~@

IIIillITIIIIl
GY

HEC035
EC-129

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS

Throttle Position Sensor(Cont&#39;d)
GA16DE forAustralia

~CEID

~BR
EC-TPS-01

THROTTLE
_.

Detectable line
POSITION for
DTC
SENSOR
-:
Non-detectable

CEID
line
forDTC

f &#34;1

I
I

I
I

t
I

q
J

I
I I

I I

I
I
I
I

I

I

I

I
I

I

I

I

I

I

I

I

I
JOINT

I

I
CONNECTOR-6

I
em

I

J

rq
~

I~

.-

t
J
J

P/L
y

B

n

1:91
1:31
15.0

I
BBB

AVCC TVOGND
ECM

!J
1

-1

-A
(ECCS
CONTROL
MODULE)

em
(fi3)
(Fi4)

~cw

EIITIIIIIIIIJ
GY

101 102
103
107 lOB 109

113
114 115 104
105
106
110 111
112
116
117
11B

EC-130 HEC068

•

INSPECTION
START

m
1

CHECK POWER SUPPLY.
NG
Repair harness orcon-

------.

1. Turn ignition switch&#34;OFF&#34;. nectors.
2. Disconnect throttleposition sensor
harness connector.
3. Turn ignition switch&#34;ON&#34;.
4. Check voltage between terminal
CD

and ground withCONSULTor tester.

Voltage: Approximately SV

m
1
0K

CHECK GROUND CIRCUIT.
NG
Check thefollowing.
1. Turn ignition switch&#34;OFF&#34;.
------.

•Harness foropen or
2. Loosen andretighten engineground short
between ECM
screw. and
throttle position
3. Check harness continuity between sensor
terminal
@
and engine ground. If
NG, repair harness or

Continuity shouldexist.
connectors.
If OK, check harness forshort.

[!J
1
0K

CHECK INPUTSIGNAL CIRCUIT.
NG
Repair harness orcon-
1. Disconnect ECMharness connector.
------.

nectors.
2. Check harness continuity between
ECM terminal
@)
or
@
and terminal

@.

Continuity shouldexist.

If OK, check harness forshort.
~OK
ADJUST THROTTLE POSITIONSEN-
SOR. Perform &#34;BasicInspection&#34;, EC-65.

~

CHECK COMPONENT NG
Replace throttleposition
(Throttle positionsensor).
------.

sensor. Toadjust it,per-
Refer to&#34;COMPONENT INSPECTION&#34; form
&#34;Basic Inspection&#34;,
on next page. EC-65.
~OK
Disconnect andreconnect harnesscon-
nectors inthe circuit. Thenretest.
~ Trouble isnot fixed.
Check ECMpinterminals fordamage
or the connection ofECM harness con-
nector. Reconnect ECMharness con-
nector andretest.

i

INSPECTION END

SEF480Q
TROUBLE
DIAGNOSIS FORNON-DETECTABLE ITEMS
Throttle Position Sensor(Cont&#39;d)
DIAGNOSTIC PROCEDURE

,~\ C/

Power steering)\
~

m

GA15DE
EC-131

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS
Throttle Position Sensor(Cont&#39;d)
~io
~ SEF461Q

II
~i8

ECM
E
CONNECTOR
II

20 23

@:
ForAustralia

@:
Except forAustralia
SEF229R
COMPONENT INSPECTION
Throttle position sensor

1. Disconnect throttleposition sensorharness connector.
2. Make surethatresistance betweenterminals
@
and
@

changes whenopening throttlevalvemanually.

SEF146R
Throttle
valveconditions
Completely closed
Partially open
Completely open Resistance
(at25&#39;C (77&#39;F)J
Approximately 0.5
kn

0.5 -4.0
kn

Approximately 4.0
kn

If NG, replace throttleposition sensor.Toadjust it,perform
&#34;Basic Inspection&#34;, EC-65.

EC-132

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS
Vehicle SpeedSensor (VSS)
LHD
models

EC-VSS-01

FUSE RefertoEL-POWER.
BLOCK
(JIB)

~

•

~ R/Y
-illfr
R/Y~~ R/Y-Ia~ VEHICLE

rITO)l~ ~I~ )
SPEED
0:@..;
I~ ~I~
(SENSOR

~ R
-lliW~
R~~ R~
@ID
COMBINATION
METER (SPEED-
OMETER)
~
~
1*.51

PU/R

I

PU
IR
IG&#34;An\

d:::,~

I~ICEID
PU/R

I

PU/R
~VSP ECM
(ECCS
CONTROL
MODULE)

ill)
B/R

-!-

~
@:

Models withtachometer

@:
Modelswithout tachometer

*1 ... @30 @40

,

*2&#34;&#39;@12 @33
*3 ... @10 &#39;@15
*4&#34;&#39;@ 9&#39;@31

,

*5 ... @ 13 @32

,

-: Detectable line
for DTC
-: Non-detectable
line forDTC

L ~

~~

tIDID11ID
B
Refer
tolast page
(Foldout page).

~@ID

tID
GY

EC-133
em

L

HEC036

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS
Vehicle SpeedSensor (VSS)(Cont&#39;d)
RHO models

EC-VSS-02

IGNITION SWITCH
ON orSTART
~R/Y
.j~
R/Y
.j~
R/Y~..gVEHICLE

rTIO\llE7iIT\
1E&#34;n\1~ )SPEED

~ I
&#39;l:1Q.y ~
I~
(SENSOR

~ R
.j1IDJ-
R
.j~
R~ ~

10A

[]]
Refer
toEL-POWER.

@:
Models withtachometer

@:
Models without tachometer

*1 @30 @40
*2
@
12 &#39;@33

*3
@
10
&#39;@
15

*4
@
9&#39;@31

,

*5 ... @13 @32

,

-: Detectable line
for DTC
-: Non-detectable
line foraTC

B/R

-!-

<f@

FUSE
BLOCK
(JIB)

~
ECM (ECCS
CONTROL
MODULE)

em

1*151

PUIR

I

PU/RtG7?l\ r=b~

I~I@

PU/R

I

PU/R

13
1
21
VSP
COMBINATION
METER (SPEED-
OMETER)
~
~

L ~

~~

tmm:lID
B
~WID

tgj
GY
Refer
tolast page
(Foldout page).

em
L

HEC037
EC-134