NISSAN ALMERA N15 1995 Service Manual

EXTERIOR

•

SBT069
SBT070

Back doorwindow molding
Bonding
portion

@
Trunk lidweatherstrip
SEC. 843
@ Back doorsidesealing rubber

SEC. 909

@ Back doorwindow molding
SEC. 900
SBT06B

Heat
gun
•
;Double-faced adhesivetape

~~~~ ..

-----~
.

~.: ..

~-o

~.
"----'
-.-/

'-

3-door

@J

Side guard molding
SEC. 766
4-door and5-door
• With avehicle coatedwithHard Clear Coat,
use double-faced 3Madhesive tapeProduct
No. 4210 orequivalent, afterpriming with3M
primer Product No.N-200 orC-100 orequiva-
lent.

@
Rear window uppermolding andside
molding

Basically thesame aswindshield uppermolding.

Refer to@ Windshield uppermolding.
@ Rear window lowermolding

Mounted withscrews.

Removal:Removemolding
by
cutting around itsperimeter.
Installation: Referto"Back doorwindow."

MBF13BAA

8T-31

@l
Back doorweatherstrip

SEC. 900

Vehicle center
Bondingportion
SBT072

@
Rear combination lamp.
dithnuts andbutyl sealant.
b' ation lamps areInstalle
w

• Rear com In

SEC. 265

BT-32

EXTERIOR
@
Front airspoiler

SEC. 960
8BT074
@
Front struttower barassembly

SEC. 401

[OJ:
N.m (kg-m, ft-lb)

8BT099
•

CAUTION:
Do not remove frontstruttower barassembly whilevehicle isjacked upwith wheels on.

8T-33

EXTERIOR

@
Rear airspoiler

• When installing, makesurethatthere arenotgaps orwaves atends ofair spoiler.
• Before installing spoiler,cleanandremove oilfrom surface wherespoiler willbemounted.

4-door sedan

SEC. 960

Sealingrubber
SBT075
3-door and5-door hatchback

SEC. 960
8T-34
Double-laced
adhesivelape
SBT076

SEAT

• When removing orinstalling theseat trim, carefully handleitto keep dirtoutand avoid damage.

* For Wiring Diagram, referto"POWER SEAT"inEL section.
Front Seat

SEC. 870

l"l
43•55 (4.4 •5.6, 32.~ \

\ t"J :'-
55 ~
L

~4.4 -5.6, 32•41)

~~@~. ~
---

iTiln> __

m
/

I: '

m ~\

tOJ
43-55 ~'}

(4.4 -5.6, 32•41)

~ 21-26 (2.1 -2.7, 15.20)

~,

~ :N.m (kg-m, ft-Ib)

SBT077
8T-35
•

SEAT
Heated Seat

• When handling seat,beextremely carefulnottoscratch heating unit.
• Toreplace heatingunit,seattrimandpadshould beseparated.
• Donot use anyorganic solvent, suchasthinner, benzene, alcohol,gasoline, etc.toclean trims.

Seatback heatingunitremoval
&
installation
Heating
unit Seat
back trim
Trim temperature Increasing
to
Decreasing to
0C (OF) 35
-45
15-25
(95 -113)
(59-77)
Thermostat OFFON
operation
SBF424H
* For Wiring Diagram, referto"HEATED SEAT"inEL section.
8T-36

4-doorsedan

SEC. 880
SEAT
Rear Seat
8T-37
Rear
seathinge
[!J

~ :N.m (kg-m, ft-Ib)

if
I

Bushing
l~';'

~«tD-1
Ol

~ 13-16 '
(1.3 -1.6,
-=\----,

9 -12) ..
<J>/
t

SBT078

•

HatchbackType-l
SEC. 880

~ ;N. m (kg-m, ft-Ib)

Type-2 SEC. 880 SEAT
Rear Seat(Cont&#39;d)

Rear seathinge
m

Rear seatback striker
r.i.1

Rear armrest h&#39;
r-&#39;I

mge~

,

Bushing
l
N7I

~~-~

~13 -16~
-I&#39;

(1.3 -1.6,
.--! &#39;)

9 •12) ~~~

)

BT-38
~
;N&#39;m (kg-m, fHb)
SBT079
SBT080

SUNROOF
ADJUSTMENT Install motor
&
limit SWassembly andsunroof railassembly inthe following sequence:

1. Arrange equallengths oflink and wire assemblies onboth sides ofsunroof opening.
2. Connect sunroofconnector tosunroof switchandpositive
(+)
power supply.
3. Set lidassembly tofully closed position
m
byoperating OPENswitch andTILT switch.
4. Fitouter sideoflid assembly tothe surface ofroof onbody outer panel.
5. Remove motor,andkeep OPEN switch pressed untilmotor pinion gearreaches theend ofits rotat-
ing range.
6. Install motor.
7. Check thatmotor drivegearfitsproperly inwires.
8. Press TILT-UP switchtocheck lidassembly fornormal tilting.
9. Check sunroof lidassembly fornormal operations (tilt-up,tilt-down, open,andclose).

FrontQ
Closing
&
opening range

81-39
ri1

9
Rear

/ Tilting up&down range

- ;:: u~
Outer bodypanel
~ Closing
&
opening range

SBF920F

•

SUNROOF
REMOVAL

• After anyadjustment, checksunroof operation andlidalignment.
• Handle finisher plateandglass lidwith care sonot tocause damage.
• Itis desirable foreasy installation tomark eachpoint before removal.

CAUTION:
Always workwithahelper.

Link andwire
assembly Sunroof
frame
assembly Shade
assembly

~
~

8T-40
Lid
assembly Motorassembly