Engine Control NISSAN ALMERA N16 2003 Electronic Owner's Manual

Cooling FanNJLC0026COMPONENTSNJLC0026S01
YLC023
CONTROL SYSTEMNJLC0026S02Cooling fans are controlled by the ECM. For details, refer to
EC-324 or EC-596, “DTC P1217 ENGINE OVER
TEMPERATURE”.
Changing Engine CoolantNJLC0037WARNING:
To avoid the danger of being scalded, never change the cool-
ant when the engine is hot.
— DRAINING ENGINE COOLANT —NJLC0037S011. Set air conditioning system as follows to prevent coolant from
remaining in the system.
a. Turn ignition switch ON and set temperature controller to maxi-
mum hot position.
b. Wait 10 seconds before turning ignition switch OFF.
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE COOLING SYSTEMQG
Cooling Fan
LC-17

SMA182B
SMA412B
Refer to MA-19, “RECOMMENDED FLUIDS AND LUBRICANTS”.
Coolant capacity (With reservoir tank):
Unit:(Imp qt)
M/T 6.7 (5-7/8)
A/TFor Sedan 6.6 (5-7/8)
For Hatchback 6.7 (5-7/8)
Reservoir tank capacity:
0.7(5/8 Imp qt)
Pour coolant through coolant filler neck slowly to allow air
in system to escape.
3. Fill radiator and reservoir tank to specified level.
4. Warm up engine to normal operating temperature without
radiator cap installed.
If coolant overflows radiator filler hole, install filler cap.
5. Run engine at 2,500 rpm for 10 seconds and return to idle
speed with radiator cap installed.
Repeat two or three times.
Watch coolant temperature gauge so as not to overheat the
engine.
6. Stop engine and cool it down.
Cool down using a fan to reduce the time.
If necessary, refill radiator up to filler neck with coolant.
7. Refill reservoir tank to MAX level line with coolant.
8. Repeat steps 4 through 7 two or more times with radiator cap
installed until coolant level no longer drops.
9. Check cooling system for leaks with engine running.
10. Warm up engine, and check for sound of coolant flow while
running engine from idle up to 3,000 rpm with heater tempera-
ture controller set at several positions between COOL and
HOT.
Sound may be noticeable at heater water cock.
11. If sound is heard, bleed air from cooling system by repeating
steps 4 through 7 until coolant level no longer drops
Clean excess coolant from engine.
— FLUSHING COOLING SYSTEM —NJLC0037S031. Open air relief plug.
2. Fill radiator with water until water spills from the air relief hole,
then close air relief plug. Fill radiator and reservoir tank with
water and reinstall radiator cap.
3. Run engine and warm it up to normal operating temperature.
4. Rev engine two or three times under no-load.
5. Stop engine and wait until it cools down.
6. Drain water.
7. Repeat steps 1 through 6 until clear water begins to drain from
radiator.
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE COOLING SYSTEMQG
Changing Engine Coolant (Cont’d)
LC-19

REMOVAL AND INSTALLATION=NJLC00631. Remove under cover.
2. Drain coolant by removing lower radiator hose.
3. Disconnect radiator upper and lower hoses.
4. Remove radiator shroud.
5. Disconnect reservoir tank hose.
6. Remove radiator mounting bracket.
7. Remove radiator.
8. After repairing or replacing radiator, install any part removed in
reverse order of removal.
When filling radiator with coolant, refer to LC-43, “Changing
Engine Coolant”.
Cooling FanNJLC0064COMPONENTSNJLC0064S01
JLC347B
CONTROL SYSTEMNJLC0064S02Cooling fans are controlled by ECM. For details, refer to EC-130,
“DTC P1217 OVER HEAT”.
ENGINE COOLING SYSTEMYD
Radiator (Cont’d)
LC-42

JLC295B
Changing Engine CoolantNJLC0079WARNING:
To avoid the danger of being scalded, never change the cool-
ant when the engine is hot.
— DRAINING ENGINE COOLANT —NJLC0079S011. Set air conditioning system as follows to prevent coolant from
remaining in the system.
a. Turn ignition switch ON and set temperature controller to maxi-
mum hot position.
b. Wait 10 seconds before turning ignition switch OFF.
SMA033D
2. Remove lower radiator hose, and remove radiator filler cap to
drain coolant.
3. Remove reservoir tank, drain coolant, then clean reservoir
tank.
Be careful not to allow coolant to contact drive belts.
4. Cover the exhaust tube heat shield to prevent from splashing
coolant.
JLC429B
YLC026
5. Remove drain plug of cylinder block and air relief plug.
6. Check drained coolant for contaminants such as rust, corro-
sion or discoloration. If contaminated flush engine cooling
system, refer to LC-45, “FLUSHING COOLING SYSTEM”.
7. Blow the coolant around the exhaust tube heat shield.
NOTE:
An asterisk (*1) in the figure means “Not installed on some
models”.
JLC298B
— REFILLING ENGINE COOLANT —NJLC0079S021. Install reservoir tank, radiator drain cock or lower radiator hose
and cylinder block drain plug.
Apply sealant to the thread of cylinder block drain plugs.
: 8 - 11 N·m (0.8 - 1.2 kg-m, 70 - 104 in-lb)
2. Fill radiator slowly with coolant until coolant spills from the air
relief plugs, then install air relief plugs.
Location of air relief plugs
Water inlet and rear side intake manifold water tubes
3. Disconnect heater hose at engine, pour coolant into the hose
so that it flows toward the heater core.
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE COOLING SYSTEMYD
Changing Engine Coolant
LC-43

While filling, if coolant from engine side spills out, be sure to
reconnect the heater hose.
Fill coolant to the level of the radiator cap at a rate of 2(1-3/4
Imp qt)/min or lower.
(Close the air relief plugs in order starting with the location from
where the coolant began spilling out.)
CAUTION:
If the filling rate is too fast, this could lead to air being mixed
in the coolant. Be sure to fill the coolant slowly according to
the rate indicated above.
Replace the copper washer of the air bleeding plug.
Air relief plug:
: 6.7 - 7.9 N·m (0.68 - 0.81 kg-m, 59 - 70 in-lb)
Use genuine Nissan anti-freeze coolant or equivalent
mixed with water (distilled or demineralized).
SMA182B
SMA412B
Refer to MA-19, “RECOMMENDED FLUIDS AND LUBRICANTS”.
Engine coolant capacity (With reservoir tank):
8.7(7-5/8 Imp qt)
Reservoir tank capacity:
0.7(5/8 Imp qt)
Pour coolant through coolant filler neck slowly to allow air
in system to escape.
4. Fill radiator and reservoir tank to specified level.
5. Warm up engine to normal operating temperature without
radiator cap installed.
If coolant overflows radiator filler hole, install radiator cap.
6. Run engine at 3,000 rpm for 10 seconds and return to idle
speed with radiator cap installed.
Repeat two or three times.
Watch coolant temperature gauge so as not to overheat the
engine.
7. Stop engine and cool it down.
Cool down using a fan to reduce the time.
If necessary, refill radiator up to filler neck with coolant.
8. Refill reservoir tank to MAX level line with coolant.
9. Repeat steps 4 through 7 two or more times with radiator cap
installed until coolant level no longer drops.
10. Check cooling system for leaks with engine running.
11. Warm up engine, and check for sound of coolant flow while
running engine from idle up to 3,000 rpm with heater tempera-
ture controller set at several positions between COOL and
HOT.
Sound may be noticeable at heater water cock.
12. If sound is heard, bleed air from cooling system by repeating
steps 4 through 7 until coolant level no longer drops
Clean excess coolant from engine.
ENGINE COOLING SYSTEMYD
Changing Engine Coolant (Cont’d)
LC-44

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
A
EC
ENGINE CONTROL SYSTEM
QG (WITH EURO-OBD)
INDEX FOR DTC ...................................................... 10
Alphabetical Index .................................................. 10
DTC No. Index ....................................................... 12
PRECAUTIONS ........................................................ 15
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 15
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 15
Precaution .............................................................. 15
Wiring Diagrams and Trouble Diagnosis ................ 18
PREPARATION ......................................................... 19
Special Service Tools ............................................. 19
Commercial Service Tools ...................................... 19
ENGINE CONTROL SYSTEM .................................. 21
System Diagram ..................................................... 21
Vacuum Hose Drawing ........................................... 22
System Chart ......................................................... 23
Multiport Fuel Injection (MFI) System .................... 23
Electronic Ignition (EI) System ............................... 25
Air Conditioning Cut Control ................................... 26
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 27
CAN Communication .............................................. 27
BASIC SERVICE PROCEDURE .............................. 30
Idle Speed and Ignition Timing Check .................... 30
Accelerator Pedal Released Position Learning ...... 31
Throttle Valve Closed Position Learning ................ 31
Idle Air Volume Learning ........................................ 31
Fuel Pressure Check .............................................. 34
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 36
Introduction ............................................................ 36
Two Trip Detection Logic ........................................ 36
Emission-related Diagnostic Information ................ 37
NATS (Nissan Anti-theft System) ........................... 49
Malfunction Indicator (MI) ....................................... 49
OBD System Operation Chart ................................ 52
TROUBLE DIAGNOSIS ............................................ 58
Trouble Diagnosis Introduction ............................... 58DTC Inspection Priority Chart ................................. 62
Fail-safe Chart ........................................................ 63
Basic Inspection ..................................................... 65
Symptom Matrix Chart ............................................ 70
Engine Control Component Parts Location ............ 74
Circuit Diagram ....................................................... 78
ECM Harness Connector Terminal Layout ............. 80
ECM Terminals and Reference Value ..................
... 80
CONSULT-II Function ............................................. 87
Generic Scan Tool (GST) Function ......................... 97
CONSULT-II Reference Value in Data Monitor Mode
... 99
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................102
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .105
Description ............................................................105
Testing Condition ..................................................105
Inspection Procedure ............................................105
Diagnostic Procedure ...........................................106
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................109
Description ............................................................109
Diagnostic Procedure ...........................................109
POWER SUPPLY CIRCUIT FOR ECM ...................110
Wiring Diagram .....................................................110
Diagnostic Procedure ............................................111
Component Inspection ..........................................115
DTC U1000, U1001 CAN COMMUNICATION LINE .116
Description ............................................................116
On Board Diagnosis Logic ....................................116
DTC Confirmation Procedure ...............................116
Wiring Diagram .....................................................117
Diagnostic Procedure ...........................................118
DTC P0011 IVT CONTROL .....................................119
Description ............................................................119
CONSULT-II Reference Value in Data Monitor Mode
.119
On Board Diagnosis Logic ....................................120
DTC Confirmation Procedure ...............................120
Diagnostic Procedure ...........................................121

EC-4
On Board Diagnosis Logic ....................................276
DTC Confirmation Procedure ...............................276
Diagnostic Procedure ...........................................277
Removal and Installation ......................................277
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION ..............................................................278
Description ............................................................278
On Board Diagnosis Logic ....................................278
DTC Confirmation Procedure ...............................278
Wiring Diagram .....................................................279
Diagnostic Procedure ...........................................280
Component Inspection ..........................................284
Removal and Installation ......................................284
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY .....................................................................285
Component Description ........................................285
CONSULT-II Reference Value in Data Monitor Mode
.285
On Board Diagnosis Logic ....................................285
DTC Confirmation Procedure ...............................285
Wiring Diagram .....................................................287
Diagnostic Procedure ...........................................288
Component Inspection ..........................................289
DTC P1128 THROTTLE CONTROL MOTOR .........291
Component Description ........................................291
On Board Diagnosis Logic ....................................291
DTC Confirmation Procedure ...............................291
Wiring Diagram .....................................................292
Diagnostic Procedure ...........................................293
Component Inspection ..........................................294
Removal and Installation ......................................295
DTC P1143 HO2S1 .................................................296
Component Description ........................................296
CONSULT-II Reference Value in Data Monitor Mode
.296
On Board Diagnosis Logic ....................................296
DTC Confirmation Procedure ...............................297
Overall Function Check ........................................298
Diagnostic Procedure ...........................................298
Component Inspection ..........................................300
Removal and Installation ......................................301
DTC P1144 HO2S1 .................................................302
Component Description ........................................302
CONSULT-II Reference Value in Data Monitor Mode
.302
On Board Diagnosis Logic ....................................302
DTC Confirmation Procedure ...............................303
Overall Function Check ........................................304
Diagnostic Procedure ...........................................304
Component Inspection ..........................................306
Removal and Installation ......................................307
DTC P1146 HO2S2 ...............................................
..308
Component Description ........................................308
CONSULT-II Reference Value in Data Monitor Mode
.308
On Board Diagnosis Logic ....................................308
DTC Confirmation Procedure ...............................308
Overall Function Check ........................................310
Wiring Diagram .....................................................311Diagnostic Procedure ............................................312
Component Inspection ..........................................314
Removal and Installation .......................................315
DTC P1147 HO2S2 ..................................................316
Component Description ........................................316
CONSULT-II Reference Value in Data Monitor Mode
.316
On Board Diagnosis Logic ....................................316
DTC Confirmation Procedure ................................317
Overall Function Check .........................................318
Wiring Diagram .....................................................319
Diagnostic Procedure ............................................320
Component Inspection ..........................................322
Removal and Installation .......................................323
DTC P1217 ENGINE OVER TEMPERATURE ........324
System Description ...............................................324
CONSULT-II Reference Value in Data Monitor Mode
.324
On Board Diagnosis Logic ....................................325
Overall Function Check .........................................325
Wiring Diagram .....................................................327
Diagnostic Procedure ............................................328
Main 12 Causes of Overheating ...........................333
Component Inspection ..........................................334
DTC P1223, P1224 TP SENSOR ............................335
Component Description ........................................335
CONSULT-II Reference Value in Data Monitor Mode
.335
On Board Diagnosis Logic ....................................335
DTC Confirmation Procedure ................................335
Wiring Diagram .....................................................337
Diagnostic Procedure ............................................338
Component Inspection ..........................................340
Removal and Installation .......................................340
DTC P1225 TP SENSOR ........................................341
Component Description ........................................341
On Board Diagnosis Logic ....................................341
DTC Confirmation Procedure ................................341
Diagnostic Procedure ............................................342
Removal and Installation .......................................342
DTC P1226 TP SENSOR ........................................343
Component Description ........................................343
On Board Diagnosis Logic ....................................343
DTC Confirmation Procedure ................................343
Diagnostic Procedure ............................................344
Removal and Installation .......................................344
DTC P1227, P1228 APP SENSOR .........................345
Component Description ........................................345
CONSULT-II Reference Value in Data Monitor Mode
.345
On Board Diagnosis Logic ....................................345
DTC Confirmation Procedure ................................345
Wiring Diagram .....................................................347
Diagnostic Procedure ............................................348
Component Inspection ..........................................350
Removal and Installation .......................................351
DTC P1229 SENSOR POWER SUPPLY ................352
On Board Diagnosis Logic ....................................352
DTC Confirmation Procedure ................................352

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA Wiring Diagram .................................................... 353
Diagnostic Procedure ........................................... 354
DTC P1706 PNP SWITCH ...................................... 356
Component Description ........................................ 356
CONSULT-II Reference Value in Data Monitor Mode
. 356
On Board Diagnosis Logic ................................... 356
DTC Confirmation Procedure ............................... 356
Overall Function Check ........................................ 357
Wiring Diagram .................................................... 358
Diagnostic Procedure ........................................... 359
DTC P1805 BRAKE SWITCH ................................ 360
Description ........................................................... 360
CONSULT-II Reference Value in Data Monitor Mode
. 360
On Board Diagnosis Logic ................................... 360
DTC Confirmation Procedure ............................... 360
Wiring Diagram .................................................... 361
Diagnostic Procedure ........................................... 362
Component Inspection ......................................... 364
IGNITION SIGNAL .................................................. 365
Component Description ........................................ 365
Wiring Diagram .................................................... 366
Diagnostic Procedure ........................................... 369
Component Inspection ......................................... 373
Removal and Installation ...................................... 374
INJECTOR CIRCUIT ............................................... 375
Component Description ........................................ 375
CONSULT-II Reference Value in Data Monitor Mode
. 375
Wiring Diagram .................................................... 376
Diagnostic Procedure ........................................... 377
Component Inspection ......................................... 380
Removal and Installation ...................................... 380
FUEL PUMP CIRCUIT ............................................ 381
Description ........................................................... 381
CONSULT-II Reference Value in Data Monitor Mode
. 381
Wiring Diagram .................................................... 382
Diagnostic Procedure ........................................... 383
Component Inspection ......................................... 385
Removal and Installation ...................................... 386
REFRIGERANT PRESSURE SENSOR ................. 387
Component Description ........................................ 387
Wiring Diagram .................................................... 388
Diagnostic Procedure ........................................... 389
Removal and Installation ...................................... 391
ELECTRICAL LOAD SIGNAL ................................ 392
Description ...................................................
........ 392
CONSULT-II Reference Value in Data Monitor Mode
. 392
Wiring Diagram .................................................... 393
Diagnostic Procedure ........................................... 394
MI & DATA LINK CONNECTORS .......................... 397
Wiring Diagram—LHD Models ............................. 397
Wiring Diagram—RHD Models ............................ 398
EVAPORATIVE EMISSION SYSTEM ..................... 399
Description ........................................................... 399
Component Inspection ......................................... 401POSITIVE CRANKCASE VENTILATION ...............402
Description ............................................................402
Component Inspection ..........................................402
SERVICE DATA AND SPECIFICATIONS (SDS) ....404
Fuel Pressure .......................................................404
Idle Speed and Ignition Timing .............................404
Calculated Load Value ..........................................404
Mass Air Flow Sensor ...........................................404
Intake Air Temperature Sensor .............................404
Engine Coolant Temperature Sensor ...................404
Heated Oxygen Sensor 1 Heater .........................404
Heated Oxygen sensor 2 Heater ..........................404
Crankshaft Position Sensor (POS) .......................404
Camshaft Position Sensor (PHASE) ....................404
Throttle Control Motor ...........................................405
Injector ..................................................................405
Fuel Pump ............................................................405
QG (WITHOUT EURO-OBD)
INDEX FOR DTC .....................................................406
Alphabetical Index ................................................406
DTC No. Index ......................................................407
PRECAUTIONS ......................................................409
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................409
On Board Diagnostic (OBD) System of Engine ....409
Precaution ............................................................409
Wiring Diagrams and Trouble Diagnosis ..............412
PREPARATION .......................................................413
Special Service Tools ...........................................413
Commercial Service Tools ....................................413
ENGINE CONTROL SYSTEM ................................415
System Diagram ...................................................415
Vacuum Hose Drawing .........................................416
System Chart ........................................................417
Multiport Fuel Injection (MFI) System ...................417
Electronic Ignition (EI) System .............................419
Air Conditioning Cut Control .................................420
Fuel Cut Control (at No Load and High Engine
Speed) ..................................................................421
CAN Communication ............................................421
BASIC SERVICE PROCEDURE .............................424
Idle Speed and Ignition Timing Check ..................424
Accelerator Pedal Released Position Learning ....425
Throttle Valve Closed Position Learning ...............425
Idle Air Volume Learning ......................................425
Fuel Pressure Check ............................................427
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..........429
Introduction ...........................................................429
Two Trip Detection Logic ......................................429
Emission-related Diagnostic Information ..............429
NATS (Nissan Anti-theft System) .........................431
Malfunction Indicator (MI) .....................................432
TROUBLE DIAGNOSIS ..........................................436
Trouble Diagnosis Introduction .............................436
DTC Inspection Priority Chart ...............................440
Fail-safe Chart ......................................................441

EC-6
Basic Inspection ...................................................443
Symptom Matrix Chart ..........................................448
Engine Control Component Parts Location ..........452
Circuit Diagram .....................................................456
ECM Harness Connector Terminal Layout ...........458
ECM Terminals and Reference Value ...................458
CONSULT-II Function ...........................................465
CONSULT-II Reference Value in Data Monitor Mode
.475
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................479
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .481
Description ............................................................481
Testing Condition ..................................................481
Inspection Procedure ............................................481
Diagnostic Procedure ...........................................482
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................485
Description ............................................................485
Diagnostic Procedure ...........................................485
POWER SUPPLY CIRCUIT FOR ECM ...................486
Wiring Diagram .....................................................486
Diagnostic Procedure ...........................................487
Component Inspection ..........................................491
DTC U1000, U1001 CAN COMMUNICATION LINE .492
Description ............................................................492
On Board Diagnosis Logic ....................................492
DTC Confirmation Procedure ...............................492
Wiring Diagram .....................................................493
Diagnostic Procedure ...........................................494
DTC P0102, P0103 MAF SENSOR .........................495
Component Description ........................................495
CONSULT-II Reference Value in Data Monitor Mode
.495
On Board Diagnosis Logic ....................................495
DTC Confirmation Procedure ...............................496
Wiring Diagram .....................................................497
Diagnostic Procedure ...........................................498
Component Inspection ..........................................500
Removal and Installation ......................................500
DTC P0117, P0118 ECT SENSOR ..........................501
Component Description ........................................501
On Board Diagnosis Logic ....................................501
DTC Confirmation Procedure ...............................502
Wiring Diagram .....................................................503
Diagnostic Procedure ...........................................504
Component Inspection ..........................................505
Removal and Installation ......................................505
DTC P0132 HO2S1 .................................................506
Component Description ........................................506
CONSULT-II Reference Value in Data Monitor Mode
.506
On Board Diagnosis Logic ....................................506
DTC Confirmation Procedure ...............................507
Wiring Diagram .....................................................508
Diagnostic Procedure ...........................................509
Component Inspection ..........................................510
Removal and Installation ......................................511DTC P0134 HO2S1 ................................................ .512
Component Description ........................................512
CONSULT-II Reference Value in Data Monitor Mode
.512
On Board Diagnosis Logic ....................................512
Overall Function Check .........................................513
Wiring Diagram .....................................................514
Diagnostic Procedure ............................................515
Component Inspection ..........................................516
Removal and Installation .......................................517
DTC P0138 HO2S2 ................................................ .518
Component Description ........................................518
CONSULT-II Reference Value in Data Monitor Mode
.518
On Board Diagnosis Logic ....................................518
DTC Confirmation Procedure ................................518
Wiring Diagram .....................................................520
Diagnostic Procedure ............................................521
Component Inspection ..........................................522
Removal and Installation .......................................523
DTC P0221 TP SENSOR ........................................524
Component Description ........................................524
CONSULT-II Reference Value in Data Monitor Mode
.524
On Board Diagnosis Logic ....................................524
DTC Confirmation Procedure ................................524
Wiring Diagram .....................................................526
Diagnostic Procedure ............................................527
Component Inspection ..........................................529
Removal and Installation .......................................529
DTC P0222, P0223 TP SENSOR ............................530
Component Description ........................................530
CONSULT-II Reference Value in Data Monitor Mode
.530
On Board Diagnosis Logic ....................................530
DTC Confirmation Procedure ................................530
Wiring Diagram .....................................................532
Diagnostic Procedure ............................................533
Component Inspection ..........................................535
Removal and Installation ......................................
.535
DTC P0226 APP SENSOR ......................................536
Component Description ........................................536
CONSULT-II Reference Value in Data Monitor Mode
.536
On Board Diagnosis Logic ....................................536
DTC Confirmation Procedure ................................536
Wiring Diagram .....................................................538
Diagnostic Procedure ............................................539
Component Inspection ..........................................541
Removal and Installation .......................................542
DTC P0227, P0228 APP SENSOR .........................543
Component Description ........................................543
CONSULT-II Reference Value in Data Monitor Mode
.543
On Board Diagnosis Logic ....................................543
DTC Confirmation Procedure ................................543
Wiring Diagram .....................................................545
Diagnostic Procedure ............................................546

EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA Component Inspection ......................................... 548
Removal and Installation ...................................... 549
DTC P0327, P0328 KS ........................................... 550
Component Description ........................................ 550
On Board Diagnosis Logic ................................... 550
DTC Confirmation Procedure ............................... 550
Wiring Diagram .................................................... 551
Diagnostic Procedure ........................................... 552
Component Inspection ......................................... 553
Removal and Installation ...................................... 553
DTC P0335 CKP SENSOR (POS) .......................... 554
Component Description ........................................ 554
CONSULT-II Reference Value in Data Monitor Mode
. 554
On Board Diagnosis Logic ................................... 554
DTC Confirmation Procedure ............................... 554
Wiring Diagram .................................................... 556
Diagnostic Procedure ........................................... 557
Component Inspection ......................................... 559
Removal and Installation ...................................... 560
DTC P0340 CMP SENSOR (PHASE) ..................... 561
Component Description ........................................ 561
On Board Diagnosis Logic ................................... 561
DTC Confirmation Procedure ............................... 561
Wiring Diagram .................................................... 563
Diagnostic Procedure ........................................... 564
Component Inspection ......................................... 566
Removal and Installation ...................................... 567
DTC P0605 ECM .................................................... 568
Component Description ........................................ 568
On Board Diagnosis Logic ................................... 568
DTC Confirmation Procedure ............................... 568
Diagnostic Procedure ........................................... 570
DTC P1065 ECM POWER SUPPLY ....................... 571
Component Description ........................................ 571
On Board Diagnosis Logic ................................... 571
DTC Confirmation Procedure ............................... 571
Wiring Diagram .................................................... 572
Diagnostic Procedure ........................................... 573
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR ............................................................ 575
Component Description ........................................ 575
On Board Diagnosis Logic ................................... 575
DTC Confirmation Procedure ............................... 575
Diagnostic Procedure ........................................... 576
Removal and Installation ...................................... 577
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION .............................................................. 578
Description ..........................................................
. 578
On Board Diagnosis Logic ................................... 578
DTC Confirmation Procedure ............................... 578
Wiring Diagram .................................................... 579
Diagnostic Procedure ........................................... 580
Component Inspection ......................................... 584
Removal and Installation ...................................... 584
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY .................................................................... 585
Component Description ........................................ 585
CONSULT-II Reference Value in Data Monitor Mode .585
On Board Diagnosis Logic ....................................585
DTC Confirmation Procedure ...............................585
Wiring Diagram .....................................................587
Diagnostic Procedure ...........................................588
Component Inspection ..........................................590
DTC P1128 THROTTLE CONTROL MOTOR .........591
Component Description ........................................591
On Board Diagnosis Logic ....................................591
DTC Confirmation Procedure ...............................591
Wiring Diagram .....................................................592
Diagnostic Procedure ...........................................593
Component Inspection ..........................................594
Removal and Installation ......................................595
DTC P1217 ENGINE OVER TEMPERATURE ........596
System Description ...............................................596
CONSULT-II Reference Value in Data Monitor Mode
.596
On Board Diagnosis Logic ....................................597
Overall Function Check ........................................597
Wiring Diagram .....................................................599
Diagnostic Procedure ...........................................600
Main 12 Causes of Overheating ...........................605
Component Inspection ..........................................606
DTC P1223, P1224 TP SENSOR ............................607
Component Description ........................................607
CONSULT-II Reference Value in Data Monitor Mode
.607
On Board Diagnosis Logic ....................................607
DTC Confirmation Procedure ...............................607
Wiring Diagram .....................................................609
Diagnostic Procedure ...........................................610
Component Inspection ..........................................612
Removal and Installation ......................................612
DTC P1225 TP SENSOR ........................................613
Component Description ........................................613
On Board Diagnosis Logic ....................................613
DTC Confirmation Procedure ...............................613
Diagnostic Procedure ...........................................614
Removal and Installation ......................................614
DTC P1226 TP SENSOR .......................................
.615
Component Description ........................................615
On Board Diagnosis Logic ....................................615
DTC Confirmation Procedure ...............................615
Diagnostic Procedure ...........................................616
Removal and Installation ......................................616
DTC P1227, P1228 APP SENSOR .........................617
Component Description ........................................617
CONSULT-II Reference Value in Data Monitor Mode
.617
On Board Diagnosis Logic ....................................617
DTC Confirmation Procedure ...............................617
Wiring Diagram .....................................................619
Diagnostic Procedure ...........................................620
Component Inspection ..........................................622
Removal and Installation ......................................623
DTC P1229 SENSOR POWER SUPPLY ................624
On Board Diagnosis Logic ....................................624
DTC Confirmation Procedure ...............................624