steering NISSAN GT-R 1998 Owner's Guide

SERVICE DATA
SECTION SD
CONTENTS
L ] RB20DE (UB) [I 17 FS5R30A 1-
ENGINE MECHANICAL ............................................... 2 MANUAL TRANSMISSION ........................................... 10
-1 RB25DE /I
ENGINE MECHANICAL .................................................. 4
17 RB25DET I]
ENGINE MECHANICAL .................................................. 6
CLUTCH.. . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . . . . . . . . . . . . .. . . . .+.. . . . . . . . . . -8
71 FS5W71C
MANUAL TRANSMISSION
.................... ......................... 9
AUTOMATIC TRANSMISSION ........................... .......... 12
TRANSFER .............. ......... ..... .. ... ........ . . ............. 18
PROPELLER SHAFT ................................................. 19
FRONT FINAL DRIVE ................................................. 20
REAR FINAL DRIVE ..................................................... 22
DRIVE SHAFT ............................................................... 24
AXLE & SUSPENSION ................................................. 25
ROAD WHEEL AND TIRE ............................................. 27
BRAKE. ... ...... . .. ... . .... . . . . . .... . .. .. . . .. . . .. . . . .. . . .. ... .. .. . . . . . . . . .. .... . -28
STEERING ........... ............. ..... ... ............... ...... ................ 29
SUPER HICAS ............................................................ 30

ENGINE MECHANICAL I RB~ODE (UB) ]
STANDARD AND REPAIR LIMIT
Firing order I 1-5-3-6-2-4
Compression pressure
MPa
(kg/cm2)/rpm
Distortion limit mm
- - -- --- - Ignition advance device
Electronically-controlled ignition advance
Engine
oil capacity
e
Spark plug standard
Limit
. Limit
of variation between cylinders
Intake manifold
Intake manifold collector
Exhaust manifold
Cylinder head
Cvlinder block
lgnition timing (during no feed back control) 1.23
(1 2%)/300
0.93 (9.5)1300
0.1 (1.0)/300
0.1 0.1
0.3
0.2
0.1
Without filter
With filter
MakerlTypeISpark
plug gap mm
Engine idling speed
W'
Idle base speed (during no feed back control)
rPm
Density of
COIHC at idling speed
Wppm Approx.
3.8
Approx. 4.2
NG WPFR5G-11 11.0
- 1
-1
650-.50
(N or P position for
A/T)
600 (N or P position for AlT)
Less than O.l/Less than 50
I New I Used I Limit
Valve
clearance
(INTIEXH)
mm
Deflection
amount of accessory V-belt
Measured with tension gauge
N (kg) Hot
engine
.
Cold engine (at ambient temperature)
Measured by pushing at 98 N (10 kg)
mm 0.36+0.062/0.53+0.062
0.31 1~,0.04/0.50i0.04
Fuel tank capacity
e
Engine coolant total capacity [with reservoir tank (max. level)] e
Thermostat opening temperature [start to open - full open]
"C
Radiator cap opening pressure
MPa (kg/cm2) Approx.
65
Approx. 9.4 82 - 95
0.06
- 0.1 0 (0.6 - 1 .O)
A/C compressor belt
Power
steering pump belt
Fan belt
Power steering pump belt
1 8-10 1 10-12 1 16
667
- 755
(68
- 77)
A/C compressor belt 1 6-8 1 7-9 / 12
Fan belt
1 3-5 1 4-6 1 7.5
559 - 637
(57
- 65)
SEC.117 Power steering
Fan belt pump be1 t
284 (29)

ENGINE MECHANICAL
STANDARD AND REPAIR LIMIT
Firing order
Compression pressure
MPa (kg/cm2)/rpm
-
Intake manifold
Intake manifold collector
--- - Standard Limit
Limit of variation between
cylinders
0.1
0.1
Distortion limit mm
Engine oil capacity
P
Spark plug
Deflection amount of accessory
V-belt Power steering pump
belt
I
- -- - - 1.26 (1 2.8)/300
0.96 (9.8)/300
0.1
(1 .OY300
Measured with tension gauge Exhaust
manifold
Cylinder head
Cylinder block
Without filter
With filter
MakerKype/Spark
plug gap
mrn
I "
650.-50 (N or P position for CVT)
600 (N or P position for AIT)
Less than O.l/Less than 50
15U600
0.36~0.06210.53~0.062
0.31 -.0.04/0.50~0.04
Approx. 65
Approx. 9.4
82 - 95
0.06 - 0.10 (0.6 - 1 .O)
"
Engine idling speed rpm
Idle base speed (during no feed back control)
rpm
Density of
COIHC at idling speed
%/ppm
Ignition timing (during no feed back control)
BTDCO/rpm
I NC compressor err
0.3
0.2
0.1
Approx. 3.8
Approx. 4.2
NGWPFR5G-11/1.0
- 1.1
lanition
advance device
1
Valve clearance (INTIEXH) mm
(kg)
/ Fan belt Electronicallv-controlled
ianition
advance
Hot engine
Cold engine (at ambient temperature)
I power steerina DU~D belt 1 8-10
Fuel tank capacity
Q
Engine
coolant total capacity [with reservoir tank (max. level)] e
Thermostat opening temperature [start to open - full open] OC
Radiator cap opening pressure
MPa (kg/crn2)
,
I Fan belt 1 3-5
Measured
by pushing at 98
N (10 kg)
mm
I SEC.! I7 Power steering I
*I I 1
AK compressor belt 1 6-8
Fan belt pump beit
Used 1 Limit

ENGINE MECHANICAL
STANDARD AND REPAIR LIMIT
Distortion limit mm
- - Intake manifold
Intake manifold collector
1 -5-3-6-2-4
1.20 (1
2.2)/300
0.90 (9.2)/300
0.1 (1.0)/300
Firing order
-- - 0.1
0.1
- -- - ( Cylinder block 0.1
Compression
pressure
MPa
(kg/cm2)/rpm
Exhaust manifold
Cvlinder head
Engine oil capacity Standard
Limit
-
Limit of variation between cylinders
0.3
0.2
- - -- - Spark plug I ~akerfl~~e/~~ark plug gap mm r NGKPFRGG-11/1.0 - 1.1
Without
filter
'with
filter
ignition advance device
I Electronically-controlled ignition advance
Approx.
3.9
Aoorox.
4.3
Engine idling speed
rPm
Idle
base speed (during no feed back control)
Pm
650-e50
(N or P position for
A/T)
600 (N or P position for AQ
Density of COIHC at idling speed
Wppm
Ignition timing (during no feed back control)
BTDCO/rpm Less
thanbl~ess than 50
15dY600
Valve clearance
(INT/EXH) mm
Deflection amount of accessory V-belt Hot
engine
Cold engine (at ambient temperature)
Measured
with tension gauge
(kg)
I
SEC.117 Power steering
Fan belt pump belt
0.36+0.062/0.53i0.062
0.3
1 20 .04/0.50a0.04
Fuel tank capacity
4
Engine coolant total capacity [with reservoir tank (max. level)] t
Thermostat opening temperature [start to open - full open]
OC
Radiator cap opening pressure
MPa (kg/cm2)
Power steering pump belt
Measured by pushing at 98
N (1 0 kg)
mm Approx.
65
Approx. 9.4
82
- 95
0.06
- 0.1 0 (0.6 - 1 .O)
New 1 Used 1 Limit
AfC
compressor belt
Fan belt
,
667 - 755
(68
- 77)
Power steering pump belt
' AfC compressor belt
Fan belt
559 - 637 284 (29)
(57 - 65)
667
- 755
(68
- 77)
667
- 755
(68
- 77)
559 - 637 284 (29)
(57 - 65)
559 - 637 284 (29) (57 - 65)
8-
10
6-8
3 - 5
- 10 - 12 16
7-9 12
4
- 6 7.5

STEERING
STEERING GEAR STEERING WHEEL
Steering wheel end play rnm -- -
Steering wheel free play rnm1 0-35 0
Steering gear type
Rack neutral position "L" mm
Amount of steering gear housing movement mm
I Within 22 PR29, PR26AD, PR26AF
68.5
STEERING
ANGLE
STEERING COLUMN
Inner wheel
Outer wheel 42"
33"
STC0101
D 88
Primary tightening torque 5.0 - 5.8 8T
Steering column length "L" mm
Retainer
adjustment
61
0
Re-tightening torque after loosening
once 5.0
- 5.8 Rs N.m (kg-m) (0.5 - 0.6)
MA
Range
within ill .5 mm from
STEERING LINKAGE Less than 98.0 EL (1 0.0)
(30.0)
Full range
Rack
sliding
force
Steering gear type
Oscillating torque 0.30
- 2.94
Nm
(kg-m)
(0.03 - 0.30) variations Less
than 147
Spring scale measurement
(at stud bolt hole) 6.48
- 64.6
N
(kg)
(0.66 - 6.59)
Tie-rod
ball joint
outer socket OIL PUMP Sliding torque 0.30 - 2.94
End play
Oscillating torque
1 .O - 7.8
Maximum oil pump pressure
MPa (kg/cm2) 8.822: (90)
(Without HICAS)
7.842:; (80)
(With HICAS)
STEERING FLUID Tie-rod ball joint
inner socket Spring
scale measurement (at
arrow position in figure below) 19.0 - 152
N (kg) (1.90 - 15.5)
Fluid capacity P I Approx. 1.0
End play mm Less than 0.2
mm 173.3
TIGHTENING TORQUE Tie-rod length "L"
Unit: N.m (kq-m)
Steering wheel nut
Steering gear to suspension member
Hydraulic tube (high pressure side) to oil
/ 50 - 68 (5.0 - 7.0)
Pump
30
- 39
(3.0 - 4.0)
89
- 91 (9.0 - 9.3)
24
- 29 (2.4 - 3.0)
30
- 39 (3.0 - 4.0)
79
- 98 (8.0 - 10.0)
32 - 42 (3.2 - 4.3)
14
- 17 (1.4 - 1.8)
Steering gear
to steering column
Outer socket to steering knuckle
Tie-rod lock nut
Oil pump fixing bolt
Hydraulic tube to
steering gear Large
Small
High pressure side
Low pressure side 15
- 24 (1.5 - 2.5)
28
- 39 (2.8 - 4.0)