NISSAN LATIO 2007 Service Repair Manual

M/T OIL
MT-9
D
E
F
G
H
I
J
K
L
MA
B
MT
Revision: June 20062007 Versa
M/T OILPFP:KLD20
Changing M/T OilUCS005LI
DRAINING
1. Start engine and let it run to warm up transaxle.
2. Stop engine. Remove drain plug (1) and drain oil.
3. Install a new gasket onto drain plug (1) and install it into tran-
saxle. Tighten drain plug to specification. Refer to MT-17, "
Case
and Housing Components" .
CAUTION:
Do not reuse gasket.
FILLING
1. Remove filler plug (1). Fill with new oil until oil level reaches the
specified limit at filler plug hole as shown.
2. After refilling oil, check oil level. Install a new gasket on filler plug
(1), then install it into transaxle. Tighten filler plug to specifica-
tion. Refer to MT-17, "
Case and Housing Components" .
CAUTION:
Do not reuse gasket.
Checking M/T OilUCS005LJ
OIL LEAKAGE AND OIL LEVEL
1. Make sure that oil is not leaking from transaxle or around it.
2. Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Do not start engine while checking oil level.
3.
Install a new gasket onto filler plug (1) and install it into tran-
saxle. Tighten filler plug to specification. Refer to MT-17, "
Case
and Housing Components" .
CAUTION:
Do not reuse gasket.
SCIA7622E
Oil grade and capacity
: Refer to MA-11, "
Fluids and Lubricants"
SCIA7623E
SCIA7623E

MT-10
SIDE OIL SEAL
Revision: June 20062007 Versa
SIDE OIL SEALPFP:32113
Removal and InstallationUCS005LK
REMOVAL
1. Remove front drive shafts from transaxle assembly. Refer to FAX-8, "Removal and Installation (Left Side)"
.
2. Remove differential side oil seal (1) using a suitable tool.
CAUTION:
Be careful not to damage transaxle case and clutch hous-
ing.
INSTALLATION
1. Install differential side oil seal (1) to clutch housing and transaxle
case using Tool (A).
2. Installation is in the reverse order of removal. Check oil level
after installation. Refer to MT-9, "
Checking M/T Oil" .
CAUTION:
Do not reuse oil seal.
SCIA7625E
Tool number A: ST38100300 (J-25523)
SCIA7626E

POSITION SWITCH
MT-11
D
E
F
G
H
I
J
K
L
MA
B
MT
Revision: June 20062007 Versa
POSITION SWITCHPFP:32005
CheckingUCS005LL
NOTE:
For removal and installation of the switches, refer to MT-17, "
Case and Housing Components"
BACK-UP LAMP SWITCH

Check continuity between terminals 1 and 2.
PARK/NEUTRAL POSITION SWITCH

Check continuity between terminals 2 and 3.
Gear position Continuity
Reverse Yes
Except reverse No
PCIB1781E
Gear position Continuity
Neutral Yes
Except neutral No

MT-12
CONTROL LINKAGE
Revision: June 20062007 Versa
CONTROL LINKAGEPFP:34103
Components of Control Device and CableUCS005LM
Removal and InstallationUCS005LN
REMOVAL
1. Remove battery. Refer to SC-9, "Removal and Installation" .
2. Remove air duct (Inlet), air duct and air cleaner case. Refer to EM-16, "
Removal and Installation" .
3. Remove shift cable from shift lever.
4. Remove select cable according to the following.
a. Move stopper (1) to the unlocked position.
1. Control lever knob 2. Control lever 3. Control device assembly
4. Select cable 5. Shift cable 6. Lock plate
7. Clutch housing 8. Cable bracket 9. Tapping bolt
10. Cable support bracket 11. Adapter plate
WCIA0626E
SCIA7842E

CONTROL LINKAGE
MT-13
D
E
F
G
H
I
J
K
L
MA
B
MT
Revision: June 20062007 Versa
b. Pull the release button (1) of select cable (2) and then remove it
from select lever (3).
5. Shift control lever to neutral position.
6. Remove control lever knob.
7. Remove center console assembly. Refer to IP-22, "
CENTER
CONSOLE ASSEMBLY" .
8. Remove control device assembly bolts.
9. Remove exhaust front tube, center muffler and heat plate. Refer
to EX-4, "
Removal and Installation" .
10. Remove cable support bracket.
11. Remove select cable and shift cable from cable bracket.
12. Remove control device assembly from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Self tapping bolts are used to attach cables to the clutch housing.

Securely assemble each cable and lever of control shaft.

Be careful about the installation direction, and push control lever
knob onto control lever.
CAUTION:
Do not reuse control lever knob.

Make sure that the front/rear claws (1) of control device assem-
bly are in contact with flange of the floor (2).

When control lever is selected to 1st-2nd side and 5th-6th side,
confirm control lever returns to neutral position smoothly.

When control lever is shifted to each position, make sure there
is no binding or disconnection in each boot.

Move stopper (1) to lock position when installing the shift cable
onto the shift lever.
WCIA0606E
SCIA7630E
PCIB1510E
SCIA7846E

MT-14
AIR BREATHER HOSE
Revision: June 20062007 Versa
AIR BREATHER HOSEPFP:31098
Removal and InstallationUCS005LO
COMPONENTS
REMOVAL
1. Remove battery. Refer to SC-9, "Removal and Installation"
2. Remove air duct (Inlet), air duct and air cleaner case. Refer to EM-16, "Removal and Installation" .
3. Remove air breather hose.
CAUTION:
When air breather hose is removed, be sure to hold two way connector securely.
INSTALLATION
Installation is in the reverse order of removal.

When installing air breather hose on two way connector, aim paint mark face toward the vehicle front.

When installing air breather hose on two way connector, push it until it hits transaxle case.

When installing air breather hose to air duct and air cleaner case, make sure that clips are fully inserted.
CAUTION:
Make sure air breather hose is not collapsed or blocked due to folding or bending when installed.
1. Air cleaner case 2. Air breather hose 3. Air duct
4. Clip 5. Transaxle assembly 6. 2 way connector
SCIA7629E

TRANSAXLE ASSEMBLY
MT-15
D
E
F
G
H
I
J
K
L
MA
B
MT
Revision: June 20062007 Versa
TRANSAXLE ASSEMBLYPFP:32010
Removal and InstallationUCS005LQ
CAUTION:
If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Inserted CSC returns to the original position when removing transaxle assembly. Dust on clutch disc
sliding parts may damage CSC seal, and may cause clutch fluid leakage.
COMPONENTS
REMOVAL
1. Drain gear oil. Refer to MT-9, "Changing M/T Oil" .
2. Drain clutch fluid and remove clutch tube from CSC. Refer to CL-9, "
Removal and Installation" .
CAUTION:
Do not depress clutch pedal during removal procedure.
3. Remove engine and transaxle assembly. Refer to EM-73, "
Removal and Installation" .
4. Remove starter motor. Refer to SC-23, "
Removal and Installation" .
5. Remove transaxle assembly to engine bolts.
6. Separate transaxle assembly from engine.
INSTALLATION
Installation is in the reverse order of removal.
1. LH engine mount bracket (transaxle
side)2. Transaxle assembly 3. Rear engine mount bracket
4. Washer 5. Rear torque rod⇐Front
: Refer to MT-15, "
INSTALLATION" for specification.
SCIA7631E

MT-16
TRANSAXLE ASSEMBLY
Revision: June 20062007 Versa

If transaxle is removed from the vehicle, always replace CSC. Refer to CL-11, "Removal and Installation" .

When installing the transaxle assembly to the engine, install the
bolts as shown.
CAUTION:
When installing transaxle assembly, be careful not to bring
transaxle input shaft into contact with clutch cover.
A: M/T to engine
B: Engine to M/T

Bleed the air from the clutch hydraulic system. Refer to CL-8, "Air Bleeding Procedure" .

After installation, check oil level, and check for leaks and loose mechanisms. Refer to MT-9, "Checking M/
T Oil" .
Bolt No. 1 2
Quantity 3 6
Bolt length “ ” mm (in)60 (2.36) 50 (1.97)
Tightening torque
N·m (kg-m, ft-lb)62.0 (6.3, 46)
PCIB1786E

TRANSAXLE ASSEMBLY
MT-17
D
E
F
G
H
I
J
K
L
MA
B
MT
Revision: June 20062007 Versa
Disassembly and AssemblyUCS005LR
COMPONENTS
Case and Housing Components
1. Filler plug 2. Gasket 3. Transaxle case
4. Bushing 5. Shift finger 6. Snap ring
7. Oil gutter 8. Oil channel 9. Position switch
10. Shift lever oil seal 11. Shift lever 12. Retaining pin
13. Bracket 14. Differential side oil seal 15. Control lever oil seal
16. Control lever 17. Magnet 18. Drain plug
19. Input shaft oil seal 20. CSC (Concentric Slave Cylinder) 21. Clutch housing
22. 2way connector 23. Pinion shaft 24. Pinion gear
Apply Genuine Silicone RTV or the equivalent. Refer to GI-XX, "Recommended chemical products and sealants"
SFIA3291E

MT-18
TRANSAXLE ASSEMBLY
Revision: June 20062007 Versa
Gear Components
1. Input shaft front bearing 2. Input shaft 3. 3rd input gear
4. Washer 5. Snap ring 6. 3rd baulk ring
7. 3rd-4th coupling sleeve 8. 3rd-4th synchronizer hub 9. Insert key
10. 4th baulk ring 11. 4th input gear 12. 5th input gear
13. 5th baulk ring 14. 5th-6th coupling sleeve 15. 5th-6th synchronizer hub
16. 6th baulk ring 17. Needle bearing 18. 6th input gear
19. Input shaft rear bearing A. Replace the parts as a set Apply gear oil
WCIA0586E