NISSAN NOTE 2016 Service Repair Manual

Page 151 of 3641

AV-146
< SYSTEM DESCRIPTION >[NAVIGATION]
DIAGNOSIS SYSTEM (AROUND VIEW MONITOR CONTROL UNIT)
DIAGNOSIS SYSTEM (AROUND VI
EW MONITOR CONTROL UNIT)
CONSULT FunctionINFOID:0000000012433017
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the around view monitor control unit.
ECU IDENTIFICATION
The part number of around view monitor control unit is displayed.
SELF DIAGNOSTIC RESULT
Refer to AV-154, "DTC Index".
DATA MONITOR
WORK SUPPORT
Direct Diagnostic Mode Description
ECU Identification The around view monitor control unit part number is displayed.
Self Diagnostic Result The around view monitor control unit self diagnostic results are displayed.
Data Monitor The around view monitor control unit input/output data is displayed in real time.
Work support The settings for around view monitor control unit functions can be changed.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing around view monitor control unit.
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item Description
ST ANGLE SENSOR SIGNAL [On/Off] Indicates condition of steering angle sensor signal.
REVERSE SIGNAL [On/Off] Indicates selector lever position.
VEHICLE SPEED SIGNAL [mph/km/h] Indicate s condition of vehicle speed signal.
CAMERA SWITCH SIGNAL [On/Off] Indicates condition of camera switch signal.
CAMERA OFF SIGNAL [On/Off] Indicates condition of camera OFF signal.
ST ANGLE SENSOR TYPE [Absolute] Indicates steering angle sensor type.
STEERING GEAR RATIO TYPE [Type
0] Indicates steering gear ratio type.
STEERING POSITION [LHD/RHD] Indi cates LH or RH drive type.
REAR CAMERA IMAGE SIGNAL [OK/
NG] Indicates condition of camera image signal.
F-CAMERA IMAGE SIGNAL [OK/NG] Indicates condition of camera image signal.
DR-SIDE CAMERA IMAGE SIG [OK/
NG] Indicates condition of camera image signal.
PA-SIDE CAMERA IMAGE SIG [OK/
NG] Indicates condition of camera image signal.
Support Item
Setting Description
NON-VIEWABLE AREA REMINDER ON
ON/OFF setting of non-viewable area can be performed.
OFF
PREDICTIVE COURSE LINE
DISPLAY ON
ON/OFF setting of predictive course line display can be performed.
OFF
INITIALIZE CAMERA IMAGE
CALIBRATION — Factory image calibration restoration can be performed.
STEERING ANGLE SENSOR
ADJUSTMENT — Steering angle sensor neutral position adjustment can be performed.
Revision: August 2015
2016 Versa Note

cardiagn.com

Page 152 of 3641

AV
DIAGNOSIS SYSTEM (AROUND VIEW MONITOR CONTROL UNIT)
AV-147
< SYSTEM DESCRIPTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
CONFIGURATION
Refer to AV-176, "CONFIGURATION (AROUND VIEW MONITO R CONTROL UNIT) : Description".
CAN DIAG SUPPORT MNTR
Refer to LAN-13, "CAN Diagnostic Support Monitor".
CALIBRATING CAMERA IMAGE
(FRONT CAMERA) STATUS
Performs calibration of front camera.
AXIS X
AXIS Y
ROTATE
CALIBRATING CAMERA IMAGE
(PASS-SIDE CAMERA) STATUS
Performs calibration of passenger side camera.
AXIS X
AXIS Y
ROTATE
CALIBRATING CAMERA IMAGE
(DR-SIDE CAMERA) STATUS
Performs calibration of driver side camera.
AXIS X
AXIS Y
ROTATE
CALIBRATING CAMERA IMAGE
(REAR CAMERA) STATUS
Performs calibration of rear view camera.
AXIS X
AXIS Y
ROTATE
FINE TUNING OF BIRDS-EYE VIEW STATUS
Confirmation and adjustment of difference between each camera can be per-
formed.
SELECT
AXIS X
AXIS Y
ROTATE
Support Item
Setting Description
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 153 of 3641

AV-148
< ECU DIAGNOSIS INFORMATION >[NAVIGATION]
AV CONTROL UNIT
ECU DIAGNOSIS INFORMATION
AV CONTROL UNIT
Reference ValueINFOID:0000000012433018
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monitor Item
ConditionValue/Status
VHCL SPD SIG Vehicle speed = 0 km/h (0 MPH).
Off
Vehicle speed > 0 km/h (0 MPH). On
ILLUM SIG Illumination signal is not received.
Off
Illumination signal is received. On
IGN SIG Ignition switch OFF or ACC.
Off
Ignition switch ON. On
REV SIG Selector lever in any position other than R.
Off
Selector lever in R position. On
AWNIA3655ZZ
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
2
(GR) 3
(P) Sound signal front speaker
LH
Output ON Sound output
4
(W) 5
(R) Sound signal rear speaker
LH
Output ON Sound output
SKIB3609E
SKIB3609E
Revision: August 2015
2016 Versa Note

cardiagn.com

Page 154 of 3641

AV
AV CONTROL UNITAV-149
< ECU DIAGNOSIS INFORMATION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P6
(SB) 15
(G) Steering switch signal A Input ON Press SOURCE switch
0V
Press switch 1.0V
Press switch 2.0V
Press switch 3.0V
Except above 5.0V
7
(W) Ground ACC power supply
Input ACC—Battery voltage
8
(L) —CAN high
Input/
Output ——

9
(R) 44
(B) Illumination control signal Input ON Headlamps ON
Battery voltage
11
(BG) 12
(V) Sound signal front speaker
RH
Output ON Sound output
13
(L) 14
(Y) Sound signal rear speaker
RH
Output ON Sound output
16
(V) 15
(G) Steering switch signal B Input ON Press switch
0V
Press switch 1.0V
Press switch 2.0V
Except above 5.0V
17
(P) —CAN low
Input/
Output ——

18
(LG) Ground Vehicle speed signal Input ON When vehicle speed is ap-
prox. 40 km/h (25 MPH)
19
(Y) Ground Battery power supply Input OFF
—Battery voltage
20
(B/W) Ground Ground
— ON— 0 V
23
(R) — MR output
Output —— —
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
JSNIA0012GB
Revision: August 2015
2016 Versa Note

cardiagn.com

Page 155 of 3641

AV-150
< ECU DIAGNOSIS INFORMATION >[NAVIGATION]
AV CONTROL UNIT
28
(Y) Ground Reverse signal
Input ONSelector lever in R (re-
verse)
Battery voltage
Selector lever in any posi-
tion other than R (reverse) 0 V
30
(Y) Ground AUX jack audio signal LH Input ON Received audio signal
(AUX input)
31
(G) Ground AUX ground
— ON— 0V
32
(L) Ground AUX jack audio signal RH Input ON Received audio signal
(AUX input)
33
(B) Ground Camera ground
— ON — 0 V
34
(L) Ground Camera power supply Output ON Camera image displayed
6.0 V
Except for above 0 V
35
(Shield) —Camera image signal
shield —— —

36
1
(Y)
Ground Camera image signal Input ON When camera image is dis-
played
36
2
(G)
37
(BG) Ground Ignition power supply Input ON
—Battery voltage
42
(L) Ground MIC VCC
Output ON—5 V
43
(P) 41
(Shield) Microphone signal
Input ONWhile speaking into micro-
phone.
45
(W) — V BUS signal
— —— —
46
(G) — USB ground
— —— —
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
SKIB2251J
SKIB3609E
Revision: August 2015
2016 Versa Note

cardiagn.com

Page 156 of 3641

AV
AV CONTROL UNITAV-151
< ECU DIAGNOSIS INFORMATION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
1: Without around view monitor
2: With around view monitor
DTC IndexINFOID:0000000012433019
47
(L) — USB D+ signal
— —— —
48
(R) — USB D
− signal — — — —
49
(Shield) — USB shield
— —— —
50
(B) Ground Antenna amp. ON signal Output ON
AV control unit ON, FM-AM
selected.Battery voltage
51
(B) Ground AM-FM main antenna Input ON AV control unit ON, FM-AM
selected.5.0 V
52
(Shield) —AM-FM main antenna
shield
—— —

55
(B) Ground GPS antenna signal Input ON
AV control unit ON, NAV se-
lected.5.0 V
56
(Shield) — GPS antenna shield
— —— —
57
(B) Ground Satellite antenna signal Input ON AV control unit ON, XM se-
lected.
5.0 V
58
(Shield) — Satellite antenna shield — —
——
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
CONSULT Display
Reference Page
U1000: CAN COMM CIRCUIT AV-186, "
AV CONTROL UNIT : DTC Logic"
U1010: CONTROL UNIT (CAN)AV-187, "AV CONTROL UNIT : DTC Logic"
U1200: Cont Unit AV- 1 9 8 , "DTC Logic"
U1217: BLUETOOTH MODULEAV- 1 9 9 , "DTC Logic"
U1229: iPod CERTIFICATIONAV- 2 0 0 , "DTC Logic"
U122F: Digital broadcasting connection errorAV- 2 0 1 , "DTC Logic"
U1244: GPS ANTENNA CONNAV- 2 0 3 , "DTC Logic"
U1258: XM ANTENNA CONNAV- 2 0 4 , "DTC Logic"
U1263: USB OVERCURRENTAV- 2 0 5 , "DTC Logic"
U1264: ANTENNA AMP TERMINALAV- 2 0 6 , "DTC Logic"
U12AA: Configuration ErrorAV- 2 0 7 , "DTC Logic"
U12AC: Display Temperature too High AV- 2 0 8 , "DTC Logic"
U12AD: ECU Temperature too High AV- 2 0 9 , "DTC Logic"
U12AE: Internal Amplifier temperature WarningAV- 2 1 0 , "DTC Logic"
U12AF: CD Mechanism Temperature Warning AV- 2 11 , "DTC Logic"
U12B0: Supply Voltage Goes below 9V > 20sAV- 2 1 2 , "DTC Logic"
U12B1: Supply Voltage Goes High > 16V for 20sAV- 2 1 3 , "DTC Logic"
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 157 of 3641

AV-152
< ECU DIAGNOSIS INFORMATION >[NAVIGATION]
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT
Reference ValueINFOID:0000000012433020
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monitor Item
ConditionValue/Status
CAMERA OFF SIGNAL CAMERA switch ON.
Off
CAMERA switch OFF. On
CAMERA SWITCH SIGNAL CAMERA switch OFF.
Off
CAMERA switch ON. On
DR-SIDE CAMERA IMAGE SIG Side camera LH inoperative.
NG
Side camera LH operative. OK
F-CAMERA IMAGE SIG Front camera inoperative.
NG
Front camera operative. OK
PA-SIDE CAMERA IMAGE SIG Side camera RH inoperative.
NG
Side camera RH operative. OK
REAR CAMERA IMAGE SIGNAL Rear view camera LH inoperative.
NG
Rear view camera LH operative. OK
REVERSE SIGNAL When selector lever is in any position other than R (reverse). Off
When selector lever in R (reverse).
On
ST ANGLE SENSOR SIGNAL Around view monitor control unit is not receiving steering angle
sensor signal.
Off
Around view monitor control unit is receiving steering angle sen-
sor signal. On
ST ANGLE SENSOR TYPE Steering angle sensor type. Absolute
STEERING GEAR RATIO TYPE Stee ring gear ratio type. Type 0
STEERING POSITION Left hand drive vehicle.
LHD
Right hand drive vehicle. RHD
VEHICLE SPEED SIGNAL While driving, equivalent to speedometer reading mph, km/h
AWNIA3139ZZ
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
1
(B) Ground Ground
— ON— 0 V
2
(G) Ground Battery power supply Input OFF
—Battery voltage
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 158 of 3641

AV
AROUND VIEW MONITOR CONTROL UNITAV-153
< ECU DIAGNOSIS INFORMATION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
4
(BR) Ground Ignition signal
Input ON—Battery voltage
8
(Y) Ground Reverse signal
Input ONSelector lever in R (re-
verse) position
Battery voltage
Selector lever in other than
R (reverse) position 0 V
10
(P) —CAN low
Input/
Output ——

12
(L) —CAN high Input/
Output ——

23
(Shield) —Camera image signal
shield
—— —

24
(W) Ground Camera image signal Output ON
When camera image dis-
play
25
(L) Ground Rear view camera ground — ON
—0 V
26
(G) Ground Rear view camera power
supply Output ONCAMERA selected
or
Shift selector in R (reverse)
position. 6.0 V
28
(Y) 27
(B) Rear view camera image
signal
Input ONCAMERA selected
or
Shift selector in R (reverse)
position.
29
(V) Ground Side camera LH ground — ON
—0 V
30
(R) Ground
Side camera LH power
supply Output ONCAMERA selected
or
Shift selector in R (reverse)
position. 6.0 V
32
(LG) 31
(Shield) Side camera LH image sig-
nal
Input ONCAMERA selected
or
Shift selector in R (reverse)
position.
33
(B) Ground Side camera RH ground — ON
—0 V
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB2251J
JSNIA0834GB
JSNIA0834GB
Revision: August 2015
2016 Versa Note

cardiagn.com

Page 159 of 3641

AV-154
< ECU DIAGNOSIS INFORMATION >[NAVIGATION]
AROUND VIEW MONITOR CONTROL UNIT
DTC Index
INFOID:0000000012433021
34
(L) Ground Side camera RH power
supply Output ONCAMERA selected
or
Shift selector in R (reverse)
position. 6.0 V
36
(Y) 35
(Shield) Side camera RH image sig-
nal
Input ONCAMERA selected
or
Shift selector in R (reverse)
position.
37
(B) Ground Front camera ground — ON
—0 V
38
(W) Ground Front camera power supply Output ON CAMERA selected
or
Shift selector in R (reverse)
position.6.0 V
40
(R) 39
(Shield) Front camera image signal Input ON CAMERA selected
or
Shift selector in R (reverse)
position.
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
JSNIA0834GB
JSNIA0834GB
CONSULT Display
Reference Page
U0428: ST ANG SEN CALIB AV-185, "
DTC Logic"
U1000: CAN COMM CIRCUITAV- 1 8 6 , "AROUND VIEW MONITOR CONTROL UNIT :
DTC Logic"
U1010: CONTROL UNIT (CAN)AV- 1 8 7 , "AROUND VIEW MONITOR CONTROL UNIT :
DTC Logic"
U111A: Rear display output signal diagnosis (Harness disconnection)
AV-188, "DTC Logic"
U111B: Right side display output signal diagnosis (Harness disconnection)AV-192, "DTC Logic"
U111C: Front display output signal diagnosis (Harness disconnection)AV-194, "DTC Logic"
U111D: Left side display output signal diagnosis (Harness disconnection)AV-196, "DTC Logic"
U1232: ST ANG SEN CALIBAV-202, "DTC Logic"
U1304: Non-completion of the calibrationAV-214, "DTC Logic"
U1305: Non-completion of the configurationAV-215, "DTC Logic"
Revision: August 2015 2016 Versa Note

cardiagn.com

Page 160 of 3641

AV
NAVIGATION SYSTEMAV-155
< WIRING DIAGRAM > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
WIRING DIAGRAM
NAVIGATION SYSTEM
Wiring DiagramINFOID:0000000012433022
ABNWA2892GB
Revision: August 2015 2016 Versa Note

cardiagn.com

Page:   < prev 1-10 ... 111-120 121-130 131-140 141-150 151-160 161-170 171-180 181-190 191-200 ... 3650 next >