NISSAN NOTE 2016 Service Repair Manual

EXT-44
< REMOVAL AND INSTALLATION >
DOOR SASH TAPE
DOOR SASH TAPE
Exploded ViewINFOID:0000000012432186
1. Front door sash front tape 2. Front door sash rear tape 3. Rear door sash front tape
4. Rear door sash rear tape 5. Center pillar tape
JMKIB0613ZZ
Revision: August 20152016 Versa Note

cardiagn.com

DOOR SASH TAPEEXT-45
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
Removal and InstallationINFOID:0000000012432187
REMOVAL
Heat door sash tape surface using a suitable tool and remove door sash tape.
CAUTION:
Use care not to damage body paint.
INSTALLATION
CAUTION:
• Degrease door assembly surface for sash tape.
• Grit or dust on surface of sash tape may spoil exterior appearance if not removed. Clean the surface
and check that no grit or dust rema ins before starting the operation.
• Do not reuse blackout tape.
1. Affix door sash tape (2) to door panel (3) by applying pressure using a squeegee (A) while peeling off release coated paper (1).
NOTE:
• Peel release coated paper at distance of 10 – 20 mm (0.4 – 0.8 in) ahead (B) of squeegee and affixblackout paper.
• To prevent any bubbles from forming, slightly lift the portion not yet affixed using a squeegee, so that
portion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using
squeegee tilted at 40 – 50 ° angle (pushing direction) (C) 30 – 45° angle (pulling direction) (D).
2. For small radius portion of hemming part, gradually apply pres- sure and affix door sash tape (1) using squeegee (A) as shown.
CAUTION:
Do not wash the vehicle with in 24 hours so as to keep
adhesive dry.
JMKIA4862GB
JMKIA4655ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EXT-46
< REMOVAL AND INSTALLATION >
DOOR OUTSIDE MOLDING
DOOR OUTSIDE MOLDING
Exploded ViewINFOID:0000000012432188
1. Front door outside molding 2. Rear door outside molding 3. Front door panel
AWKIA2517ZZ
Revision: August 20152016 Versa Note

cardiagn.com

DOOR OUTSIDE MOLDINGEXT-47
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
Removal and InstallationINFOID:0000000012432189
FRONT DOOR OUTSIDE MOLDING
Removal
1. Lower front door glass fully.
2. Release the pawls using a suitable tool, then rotate front door outside molding toward the outside of the vehicle and lift up to remove.
Installation
Installation is in the reverse order of removal.
REAR DOOR OUTSIDE MOLDING
Removal
1. Lower rear door glass fully.
2. Release the pawl using a suitable tool, then rotate rear door outside molding toward the outside of the
vehicle and lift up to remove.
Installation
Installation is in the reverse order of removal.
4. Rear door panel 5. Rear door glass6. Front door glass
Pawl
Revision: August 2015 2016 Versa Note

cardiagn.com

EXT-48
< REMOVAL AND INSTALLATION >
BACK DOOR OUTER FINISHER
BACK DOOR OUTER FINISHER
Exploded ViewINFOID:0000000012432190
Removal and InstallationINFOID:0000000012432191
REMOVAL
1. Remove back door inner finisher. Refer to INT-36, "BACK DOOR INNER FINISHER : Removal and Instal-
lation".
2. Disconnect the harness connectors from back door request switch.
3. Remove back door outer finisher nuts.
4. Release clips and remove the back door outer finisher.
5. Remove back door request switch from t he back door outer finisher (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing back door finisher, check that clips are securely placed into body panel holes.
1. Rear camera (if equipped) 2. Back door outer finisher 3. Back door request switch
Clip
AWKIA2514ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

REAR SPOILEREXT-49
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
REAR SPOILER
Exploded ViewINFOID:0000000012432192
Removal and InstallationINFOID:0000000012432193
REMOVAL
1. Open back door.
2. Remove rear spoiler bolt hole covers (1).
3. Remove rear spoiler bolts.
4. Use heat gun and suitable tool to release two way tapes.
5. Release rear spoiler clips and remove rear spoiler.
INSTALLATION
Installation is in reverse order of removal.
NOTE:
1. Rear spoiler 2. Back door3. Back door outer finisher
Clip
ALKIA3634ZZ
ALKIA3639ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EXT-50
< REMOVAL AND INSTALLATION >
REAR SPOILER
Apply new adhesive tape (A) to rear spoiler (1) in the areas shown.
ALKIA3640ZZ
Revision: August 20152016 Versa Note

cardiagn.com

FAX-1
TRANSMISSION & DRIVELINE
CEF
G H
I
J
K L
M
SECTION FA X
A
B
FA X
N
O P
CONTENTS
FRONT AXLE
PRECAUTION ....... ........................................2
PRECAUTIONS .............................................. .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
Precaution for Drive Shaft .........................................2
Precautions for Wheel Hub and Knuckle ..................2
PREPARATION ............................................3
PREPARATION .............................................. .....3
Special Service Tools .......................................... ......3
Commercial Service Tools ........................................4
SYMPTOM DIAGNOSIS ...............................6
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING ........................ .....
6
NVH Troubleshooting Chart ................................ ......6
PERIODIC MAINTENANCE ..........................7
FRONT WHEEL HUB AND KNUCKLE ......... .....7
Inspection ............................................................ ......7
FRONT DRIVE SHAFT ........................................8
Inspection ............................................................ ......8
REMOVAL AND INSTALLATION ................9
FRONT WHEEL HUB AND KNUCKLE ......... .....9
Exploded View ..................................................... .....9
Removal and Installation ..........................................9
Disassembly and Assembly .....................................11
Inspection ................................................................13
FRONT DRIVE SHAFT BOOT ..........................14
Exploded View .........................................................14
WHEEL SIDE ......................................................... ....14
WHEEL SIDE : Removal and Installation ................15
TRANSAXLE SIDE ................................................ ....18
TRANSAXLE SIDE : Removal and Installation .......18
Inspection ............................................................ ....18
FRONT DRIVE SHAFT .....................................19
Exploded View .........................................................19
Removal and Installation .........................................19
UNIT DISASSEMBLY AND ASSEMBLY ....21
FRONT DRIVE SHAFT .....................................21
Exploded View ..................................................... ....21
Disassembly and Assembly .....................................22
SERVICE DATA AND SPECIFICATIONS
(SDS) ............... .......................................... ...
27
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................
27
Wheel Bearing ..................................................... ....27
Drive Shaft ...............................................................27
Revision: August 2015 2016 Versa Note

cardiagn.com

FAX-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012431882
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Drive ShaftINFOID:0000000012431883
Observe the following precautions when disassembling and assembling drive shaft.
• Do not disassemble joint sub-assembly because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Clean the parts, before disassembling and assembling.
• Prevent the entry of foreign objects dur ing disassembly of the service location.
• Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be placed over parts.
• Use paper waste. Fabric shop cloths must not be used because of the danger of lint adhering to parts.
• Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with air or wiping with paper waste.
Precautions for Wheel Hub and KnuckleINFOID:0000000012431884
Observe the following precautions when assembling wheel hub and knuckle.
• Perform work in a location which is as dust-free as possible.
• Use paper waste. Fabric shop cloths must not be used because of the danger of lint adhering to parts.
• If any of wheel hub, steering knuckle, wheel bearing, and wheel hub lock nut is dropped, it must not be used.
• Always check that the tools used for press-fit work of wheel hub and wheel bearing have no wear and defor- mation so that a pressure can be applied vertically.
Revision: August 2015 2016 Versa Note

cardiagn.com

PREPARATIONFAX-3
< PREPARATION >
CEF
G H
I
J
K L
M A
B
FA X
N
O P
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000012431885
The actual shape of the tools may di ffer from those illustrated here.
Tool number
(TechMate No.)
To o l n a m e Description
KV40104000
(—)
Hub lock nut wrench Removing and Installing wheel hub lock
nut
a: 85 mm (3.35 in)
b: 65 mm (2.56 in)
ST33710000
(—)
Drift Removing wheel hub
a: 30 mm (1.18 in) dia.
b: 23 mm (0.91 in) dia.
ST30031000
(—)
Puller Removing wheel bearing inner race (out-
er)
ST35321000
(—)
Drift • Removing wheel bearing
• Installing wheel hub
a: 49 mm (1.93 in) dia.
b: 41 mm (1.61 in) dia.
ST35271000
(—)
Drift Installing wheel bearing
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
ST33061000
(—)
Drift Installing wheel hub
a: 38 mm (1.50 in) dia.
b: 28.5 mm (1.122 in) dia.
ZZA0802D
ZZA1233D
ZZA0700D
ZZA1051D
ZZA0837D
ZZA1051D
Revision: August 2015
2016 Versa Note

cardiagn.com