NISSAN NOTE 2016 Service Repair Manual

INT-20
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
3. Release the metal clip (A) behind the manual window crank han-dle using a suitable tool (B). Pull the manual window crank han-
dle (3) outward from the front door finisher and remove handle.
4. Remove rear door finisher bolt (A).
5. Release rear door finisher clips using a suitable tool (A) and remove rear door finisher as shown.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing rear door finisher, check that clips and pawls are securely placed into door panel
holes.
AWJIA1119ZZ
JMJIA6028ZZ
AWJIA1121ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BODY SIDE TRIMINT-21
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
BODY SIDE TRIM
Exploded ViewINFOID:0000000012431864
FRONT PILLAR FINISHER
FRONT PILLAR FINISHER : Removal and InstallationINFOID:0000000012431865
REMOVAL
1. Remove front pillar portion of front body side welt.
1. Center pillar upper finisher (RH) 2. Front body side welt (RH) 3. Front pillar finisher (RH)
4. Dash side finisher (RH) 5. Front kicking plate (RH) 6. Center pillar lower finisher (RH)
7. Rear kicking plate (RH) 8. Rear body side welt (RH) Front Clip Pawl
AWJIA1482ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2. Pull front pillar finisher downward as shown to release the frontpillar finisher clip (bottom).
: Clip
: Pawl
3. Cut and discard front pillar finisher tether clips.
4. Remove the remaining piece of the tether clip (B) using a suit- able tool (A).
INSTALLATION
1. Install new front pillar finisher tether clips (A) to the front pillarfinisher by inserting clip end and rotating 90 degrees to fit.
CAUTION:
• Do not reuse tether clips. Replace with new part after
removal.
• Make sure to install tether clip to front pillar finisher before installing front pillar finisher.
• When installing tether clip to front pillar finisher, be sure to install by aligning to the cutout.
• Visually check the clip for deformation and damage dur-
ing installation. Replace with new one if necessary.
• When installing front pillar finisher, check that clip and
tether clips are securely placed into body panel holes.
2. Install the front pillar finisher to the front pillar.
KICKING PLATE
KICKING PLATE : Removal and InstallationINFOID:0000000012431866
FRONT KICKING PLATE
Removal
AWJIA1124ZZ
AWJIA1111ZZ
AWJIA1088ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BODY SIDE TRIMINT-23
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
1. Release front kicking plate pawls and metal clip using a suitable tool (A) and remove front kicking plate as shown.
: Pawl
: Metal clip
Installation
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for defo rmation and damage during installation.
• When installing front kicking plate, check that clips and pawls are securely placed into body panel holes.
REAR KICKING PLATE
Removal
1. Remove rear seat cushion. Refer to SE-41, "Seat Cushion".
2. Lift rear end of rear kicking plate to release metal clip, then rotate front end of rear kicking plate to release pawls and
remove.
: Pawl
: Metal clip
: Clip
Installation
Installation is in the reverse order of removal.
AWJIA1123ZZ
AWJIA1483ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing rear kicking plate, check that clips and pawls ar e securely placed into body panel
holes.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and InstallationINFOID:0000000012431867
REMOVAL
1. Remove front kicking plate. Refer to INT-22, "KICKING PLATE : Removal and Installation".
2. Lift up rear end of dash side finisher to release pawls. : Pawl
3. Pull back dash side finisher to release dash side finisher from stud and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the pawls for deformati on and damage during installation.
• When installing, check that fi nisher is aligned with stud bolt located on floor panel.
• When installing dash side fi nisher, check that pawls are secure ly placed into body panel holes.
BODY SIDE WELT
BODY SIDE WELT : Removal and InstallationINFOID:0000000012431868
FRONT BODY SIDE WELT
Removal
1. Remove the dash side finisher. Refer to INT-24, "DASH SIDE FINISHER : Removal and Installation".
2. Remove front body side welt.
Installation
Installation is in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Remove rear kicking plate. Refer to INT-22, "KICKING PLATE : Removal and Installation".
2. Remove rear body side welt.
AWJIA1092ZZ
AWJIA1093ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BODY SIDE TRIMINT-25
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
CENTER PILLAR LOWER FINISHER
: Removal and InstallationINFOID:0000000012431869
REMOVAL
1. Remove front kicking plate and rear kicking plate. Refer to INT-22, "KICKING PLATE : Removal and
Installation".
2. Remove center pillar lower finisher as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the pawls and clips for deformation and damage during installation. Replace compo-
nent if necessary.
CENTER PILLAR UPPER FINISHER
CENTER PILLAR UPPER FINISHER : Removal and InstallationINFOID:0000000012431870
REMOVAL
CAUTION:
• Be careful not to apply excessive for ce when removing center pillar upper finisher. Otherwise, clip
may be damaged and fragments may drop in body panels.
1. Slide front seat to the full forward position.
2. Release pawls, using a suitable tool and remove the seat belt height adjuster finisher (1).
: Pawl
3. Remove front D-ring anchor bolt. CAUTION:
Before removing D-ring anchor bolt note the positions of washers and spacers for correct installa-
tion.
4. Remove front body side welt and rear body side welt. Refer to INT-24, "
BODY SIDE WELT : Removal and
Installation".
5. Remove center pillar lower finisher. Refer to INT-25, "
CENTER PILLAR LOWER FINISHER : Removal
and Installation".
6. Release center pillar upper finisher upper clip using a suitable tool as shown. CAUTION:
JMJIA6045ZZ
AWHIA0539ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

INT-26
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
When releasing molded in clip, follow the steps as shown to prevent finisher or clip damage.
7. Release center pillar upper finisher lower clip using a suitable tool (A) and remove.
: Clip
CAUTION:
Do not reuse center pillar upper finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse center pillar upper finisher. Replace with new part for installation.
• When installing center pillar upper finisher, check that clips are securely placed in body panel holes.
PIIB2600J
AWJIA1094ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

FLOOR TRIMINT-27
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
FLOOR TRIM
Exploded ViewINFOID:0000000012431871
Removal and InstallationINFOID:0000000012431872
WARNING:
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals then wait at
least three minutes.
• Do not drop the seat belt retractor. Always handle it with care.
• Always point pretensioner cylinder away from body when handling.
REMOVAL
1. Remove front seats. Refer to SE-20, "DRIVER SIDE : Removal and Installation" (Driver side) and SE-22,
"PASSENGER SIDE : Removal and Installation" (Passenger side).
2. Remove rear seatback hinge. Refer to SE-27, "
SEATBACK HINGE : Removal and Installation".
3. Remove center console lower. Refer to IP-20, "
Removal and Installation".
4. Remove dash side finishers (LH/RH). Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installa-
tion".
5. Remove center pillar lower finishers (LH/RH). Refer to INT-25, "
CENTER PILLAR LOWER FINISHER :
Removal and Installation".
1. Harness clip A2. Harness clip B3. Floor trim
4. Carpet hook 5. Front floor spacer (RH) 6. Front floor spacer (LH)
7. Rear floor spacer (LH) 8. Rear floor spacer (RH) Front
Clip
AWJIA1142ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

INT-28
< REMOVAL AND INSTALLATION >
FLOOR TRIM
6. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-70,
"Removal and Installation (Battery)".
WARNING:
Before servicing the SRS, turn th e ignition switch off, disconnect both battery terminals then wait
at least three minutes.
7. Disconnect the harness connector (A ) from the seat belt retrac-
tor (1).
WARNING:
• Do not drop the seat belt retractor. Always handle it with care.
• Always point pretensioner cylinder away from body when handling.
CAUTION:
• For removing/installing the shoulder belt pre-tensioner harness connector, insert a thin screwdriver wrapped in
tape into the notch, then lift the lock and remove the har-
ness connector as shown.
• Install the harness connector with the lock raised, and push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
8. Remove seat belt lower anchor bolt. CAUTION:
Before removing the seat belt lower anchor bolt , note the positions of washers and spacers for
correct installation.
9. Remove diagnosis sensor unit. Refer to SR-30, "
Removal and Installation".
10. Remove shift selector. Refer to TM-20, "
Exploded View" (5MT) or TM-231, "Removal and Installation"
(CVT).
11. Remove A/C unit assembly bolt (C) and bracket (1) from vehicle.
12. Remove instrument panel lower bracket bolt (B) and screw (A) and reposition bracket as necessary to remove floor trim.
ALHIA0316ZZ
PHIA0953J
ALJIA0712ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

FLOOR TRIMINT-29
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
13. Release carpet hook clips with a suitable tool (A) and remove. : Clip
14. Release pawls using a suitable tool (A) and open the harness clips.
: Pawl
15. Remove floor trim.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace harness protector B with a new part af ter removal. Do not reuse harness protector B.
AWJIA0736ZZ
AWJIA0737ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com