NISSAN NOTE 2016 Service Repair Manual

INT-30
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
Exploded ViewINFOID:0000000012431873
1. Headlining2. Rear assist grip (RH)3. Front assist grip (RH)
4. Microphone (if equipped) 5. Sun visor holder (RH) 6. Sun visor holder (LH)
7. Map lamp 8. Sun visor (RH)9. Sun visor (LH)
10. Interior room lamp 11. Rear assist grip (LH)A. Headlining clip
Pawl Metal clip
AWJIA1907ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

HEADLININGINT-31
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
Removal and InstallationINFOID:0000000012431874
REMOVAL
1. Remove front pillar finishers (LH/RH). Refer to INT-21, "FRONT PILLAR FINISHER : Removal and Instal-
lation".
2. Remove sun visor screws and sun visors (LH/RH).
3. Remove map lamp. Refer to INL-51, "
Removal and Installation".
4. Remove interior room lamp. Refer to INL-53, "
Removal and Installation".
5. Remove microphone (if equipped). Refer to AV-59, "
Removal and Installation".
6. Remove center pillar upper finishers (LH/RH). Refer to INT-25, "
CENTER PILLAR UPPER FINISHER :
Removal and Installation".
7. Remove luggage side upper finishers (LH/RH). Refer to INT-35, "
LUGGAGE SIDE UPPER FINISHER :
Removal and Installation".
8. Insert a suitable tool (A) at approximately a 30 degree angle into the sun visor holder notch on the front of the sun visor holder (1)
and press in the locking tab (B) to release it. While holding in
lock tab (B), rotate the sun visor holder (1) 90 degrees to release
it from the headlining.
: Front
CAUTION:
Do not force the sun visor ho lder when removing as the
locking tab may be damaged if the suitable tool is not posi-
tioned correctly.
NOTE:
If the sun visor holder (1) does not fully rotate, make sure that
the suitable tool (A) is pressing in on the locking tab (B) and is
not positioned under locking tab (B). Reinsert the suitable tool
(A) as necessary to release the locking tab (B).
9. Release assist grip pawls and remove bolt (A) using a suitable tool and remove all assist grips.
:Pawl
10. Remove headlining clips.
11. Remove headlining through the back door. CAUTION:
• Do not reuse headlining.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Remove all remaining adhesive from roof panel.
• Do not reuse headlini ng. Replace with new part after removal.
ALJIA0537ZZ
AWJIA1126ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

INT-32
< REMOVAL AND INSTALLATION >
HEADLINING
• Apply adhesive (NISSAN P/N 999MP-57302NP or equivalent) as shown before installing headlining.
• Do not bend headlining when installing.
• When installing headlining, start by installing bo th sun visor holders and headlining clips to hold
headlining in position.
• Be careful that the surface is not wrinkled when installing.
1. Headlining A. Adhesive application location
B. NISSAN P/N 999MP-57302NP or equivalent C. 8 mm
D. 5 mm
AWJIA1102ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

LUGGAGE TRIMINT-33
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
LUGGAGE TRIM
Exploded ViewINFOID:0000000012431875
LUGGAGE REAR PLATE
1. Parcel shelf finisher (if equipped) 2. Luggage floor board (if equipped) 3. Luggage side upper finisher (LH)
4. Luggage side front reinforcement (LH) 5. Luggage side rear reinforcement (LH) 6. Luggage side lower finisher (LH)
7. Luggage rear plate 8. Luggage side lower finisher (RH) 9. Luggage side rear reinforcement (RH)
10. Luggage side front reinforcement (RH) 11. Luggage side upper finisher (RH) 12. Luggage side front cover (RH)
13. Luggage side clip 14. Luggage side rear cover (RH) 15. Luggage floor box
16. Luggage side rear cover (LH) 17. Luggage side front cover (LH) 18. Luggage floor trim
Pawl Metal clip Clip
Front
AWJIA1129ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

IN T - 3 4
< REMOVAL AND INSTALLATION >
LUGGAGE TRIM
LUGGAGE REAR PLATE : Removal and Installation
INFOID:0000000012431876
REMOVAL
1. Remove luggage floor board (if equipped).
2. Remove luggage floor trim.
3. Remove luggage rear plate clips (A).
4. Release luggage rear plate clips using a suitable tool (A) and remove luggage rear plate as shown.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing luggage rear plate, check that clips are securely placed into body holes.
LUGGAGE SIDE LOWER FINISHER
LUGGAGE SIDE LOWER FINISHER : Removal and InstallationINFOID:0000000012431877
REMOVAL
1. Partially remove rear body side welt. Refer to INT-24, "BODY SIDE WELT : Removal and Installation".
2. Remove luggage floor board (if equipped).
3. Remove luggage floor trim.
4. Remove seat back hinge. Refer to SE-27, "
SEATBACK HINGE : Removal and Installation".
5. Release rear parcel shelf finisher clips using a su itable tool and remove rear parcel shelf finisher (if
equipped).
6. Remove luggage side lower finisher pawls using a suitable tool.
AWJIA1127ZZ
AWJIA1128ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

LUGGAGE TRIMINT-35
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
: Pawl
7. Release the harness connector from cargo room lamp (RH only) and remove luggage side lower finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for defo rmation and damage during installation.
• When installing lu ggage side clip, press luggag e side clip so that upper side stamp mark faces
toward passenger room, and then completely engage luggage side clip pawls.
LUGGAGE SIDE UPPER FINISHER
LUGGAGE SIDE UPPER FINISHER : Removal and InstallationINFOID:0000000012431878
REMOVAL
1. Remove luggage side lower finisher. Refer to INT-34, "LUGGAGE SIDE LOWER FINISHER : Removal
and Installation".
2. Remove seat belt lower anchor bolt.
3. Release luggage side upper finisher clips using a suitable tool and remove luggage side upper finisher.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage during installation.
• When installing luggage side upper finisher, check that clips are placed in body holes.
AWJIA1095ZZ
AWJIA1097ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

INT-36
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
BACK DOOR TRIM
Exploded ViewINFOID:0000000012431879
BACK DOOR INNER FINISHER
BACK DOOR INNER FINISHER : Removal and InstallationINFOID:0000000012431880
REMOVAL
1. Release back door inner finisher clips using a suitable tool and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips for deformat ion and damage during installation.
• When installing back door inner finisher, check th at locate pin and clips are placed in body panel
holes.
BACK DOOR PULL HANDLE
BACK DOOR PULL HANDLE : Removal and InstallationINFOID:0000000012431881
REMOVAL
1. Release pawls using a suitable tool and remove.
INSTALLATION
1. Back door inner finisher 2. Back door panel 3. Back door pull handle
Clip Pawl
AWJIA1485ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BACK DOOR TRIMINT-37
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
Installation is in the reverse order of removal.
CAUTION:
• Visually check the pawls for deformation and damage during installation.
• When installing, confirm upper and lower orientat ion of back door pull handle, then install it.
• When installing back door pull handle, check that pawls are placed in body panel holes.
Revision: August 2015 2016 Versa Note

cardiagn.com

LAN
LAN-1
ELECTRICAL & POWER CONTROL
C
DE
F
G H
I
J
K L
B
SECTION LAN
A
O P
N
CONTENTS
LAN SYSTEM
CAN FUNDAMENTAL
HOW TO USE THIS MANU AL ......................
5
HOW TO USE THIS SECTION ....................... .....5
Information .......................................................... ......5
PRECAUTION ...............................................6
PRECAUTIONS .............................................. .....6
Precautions for Trouble Diagnosis ...................... ......6
Precautions for Harness Repair ................................6
SYSTEM DESCRIPTION . .............................7
SYSTEM ......................................................... .....7
CAN COMMUNICATION SYSTEM .............................7
CAN COMMUNICATION SYSTEM : System De-
scription ............................................................... ......
7
DIAG ON CAN ....................................................... ......7
DIAG ON CAN : System Description ........................7
TROUBLE DIAGNOSIS ......................................9
Component Description ....................................... ......9
Condition of Error Detection ......................................9
Symptom When Error Occurs in CAN Communi-
cation System ...................................................... ....
10
CAN Diagnosis with CONSULT ..............................12
Self-Diagnosis .........................................................13
CAN Diagnostic Support Monitor ............................13
How to Use CAN Communication Signal Chart ......15
BASIC INSPECTION ...................................16
DIAGNOSIS AND REPAIR WORKFLOW ..... ....16
Trouble Diagnosis Flow Chart ............................. ....16
CAN
HOW TO USE THIS MANU AL .....................
21
HOW TO USE THIS SECTION ....................... ....21
Information ........................................................... ....21
Abbreviation List ......................................................21
PRECAUTION ..............................................22
PRECAUTIONS .................................................22
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
22
Precautions for Trouble Diagnosis ..........................22
Precautions for Harness Repair ..............................22
SYSTEM DESCRIPTION .............................24
COMPONENT PARTS ......................................24
Component Parts Location .................................. ....24
SYSTEM ............................................................25
CAN COMMUNICATION SYSTEM ........................ ....25
CAN COMMUNICATION SYSTEM : System De-
scription ............................................................... ....
25
CAN COMMUNICATION SYSTEM : CAN Com-
munication Control Circuit .......................................
28
CAN COMMUNICATION SYSTEM : CAN System
Specification Chart ..................................................
29
CAN COMMUNICATION SYSTEM : CAN Com-
munication Signal Chart ..........................................
30
WIRING DIAGRAM ......................................33
CAN SYSTEM .. .................................................33
Wiring Diagram .................................................... ....33
BASIC INSPECTION ...................................39
DIAGNOSIS AND REPAIR WORKFLOW ........39
Interview Sheet .................................................... ....39
DTC/CIRCUIT DIAGNOSIS .........................40
MALFUNCTION AREA CHART ........................40
Main Line ............................................................. ....40
Revision: August 2015 2016 Versa Note

cardiagn.com

LAN-2
Branch Line ............................................................40
Short Circuit ............................................................40
MAIN LINE BETWEEN IPDM-E AND DLC
CIRCUIT .............................................................
41
Diagnosis Procedure ........................................... ...41
MAIN LINE BETWEEN IPDM-E AND AVM
CIRCUIT .............................................................
42
Diagnosis Procedure ........................................... ...42
MAIN LINE BETWEEN AVM AND DLC CIR-
CUIT ...................................................................
43
Diagnosis Procedure ........................................... ...43
ECM BRANCH LINE CIRCUIT ..........................44
Diagnosis Procedure ........................................... ...44
ABS BRANCH LINE CIRCUIT ..........................45
Diagnosis Procedure ........................................... ...45
IPDM-E BRANCH LINE CIRCUIT .....................46
Diagnosis Procedure ........................................... ...46
TCM BRANCH LINE CIRCUIT ..........................47
Diagnosis Procedure ........................................... ...47
AVM BRANCH LINE CIRCUIT ..........................48
Diagnosis Procedure ........................................... ...48
A-BAG BRANCH LINE CIRCUIT ......................49
Diagnosis Procedure ........................................... ...49
AV BRANCH LINE CIRCUIT .............................50
Diagnosis Procedure ........................................... ...50
DLC BRANCH LINE CIRCUIT ...........................51
Diagnosis Procedure ........................................... ...51
EPS BRANCH LINE CIRCUIT ...........................52
Diagnosis Procedure ........................................... ...52
M&A BRANCH LINE CIRCUIT ..........................53
Diagnosis Procedure ........................................... ...53
STRG BRANCH LINE CIRCUIT ........................54
Diagnosis Procedure ........................................... ...54
BCM BRANCH LINE CIRCUIT ..........................55
Diagnosis Procedure ........................................... ...55
CAN COMMUNICATION CIRCUIT ....................56
Diagnosis Procedure ........................................... ...56
CAN SYSTEM (TYPE 501)
DTC/CIRCUIT DIAGNOSIS ...................... ...
58
MAIN LINE BETWEEN IPDM-E AND DLC
CIRCUIT .......................................................... ...
58
Diagnosis Procedure ........................................... ...58
ECM BRANCH LINE CIRCUIT ..........................59
Diagnosis Procedure ........................................... ...59
ABS BRANCH LINE CIRCUIT ..........................60
Diagnosis Procedure ............................................ ...60
IPDM-E BRANCH LINE CIRCUIT .....................61
Diagnosis Procedure ............................................ ...61
A-BAG BRANCH LINE CIRCUIT ......................62
Diagnosis Procedure ............................................ ...62
DLC BRANCH LINE CIRCUIT ..........................63
Diagnosis Procedure ............................................ ...63
EPS BRANCH LINE CIRCUIT ...........................64
Diagnosis Procedure ............................................ ...64
M&A BRANCH LINE CIRCUIT ..........................65
Diagnosis Procedure ............................................ ...65
STRG BRANCH LINE CIRCUIT ........................66
Diagnosis Procedure ............................................ ...66
BCM BRANCH LINE CIRCUIT ..........................67
Diagnosis Procedure ............................................ ...67
CAN COMMUNICATION CIRCUIT ...................68
Diagnosis Procedure ............................................ ...68
CAN SYSTEM (TYPE 502)
DTC/CIRCUIT DIAGNOSIS ........................
70
MAIN LINE BETWEEN IPDM-E AND AVM
CIRCUIT .......................................................... ...
70
Diagnosis Procedure ............................................ ...70
MAIN LINE BETWEEN AVM AND DLC CIR-
CUIT ...................................................................
71
Diagnosis Procedure ............................................ ...71
ECM BRANCH LINE CIRCUIT ..........................72
Diagnosis Procedure ............................................ ...72
ABS BRANCH LINE CIRCUIT ..........................73
Diagnosis Procedure ............................................ ...73
IPDM-E BRANCH LINE CIRCUIT .....................74
Diagnosis Procedure ............................................ ...74
AVM BRANCH LINE CIRCUIT ..........................75
Diagnosis Procedure ............................................ ...75
A-BAG BRANCH LINE CIRCUIT ......................76
Diagnosis Procedure ............................................ ...76
AV BRANCH LINE CIRCUIT .............................77
Diagnosis Procedure ............................................ ...77
DLC BRANCH LINE CIRCUIT ..........................78
Diagnosis Procedure ............................................ ...78
EPS BRANCH LINE CIRCUIT ...........................79
Diagnosis Procedure ............................................ ...79
M&A BRANCH LINE CIRCUIT ..........................80
Revision: August 2015 2016 Versa Note

cardiagn.com