NISSAN NOTE 2016 Service Repair Manual

PB-8
< REMOVAL AND INSTALLATION >
PARKING BRAKE REAR CABLE
PARKING BRAKE REAR CABLE
Removal and InstallationINFOID:0000000012430692
REMOVAL
1. Remove the center console assembly. Refer to IP-18, "Removal and Installation".
2. Loosen the adjusting nut. Refer to PB-6, "
Exploded View".
NOTE:
It is not necessary to remove the parking brake front cable.
3. Separate the parking brake rear cables (RH/LH ) from the parking brake front cable. Refer to PB-6,
"Exploded View".
4. Remove the rear wheels and tires using power tool. Refer to WT-48, "
Exploded View".
5. Remove rear wheel sensors. Refer to BRC-143, "
REAR SENSOR ROTOR : Removal and Installation".
6. Remove the rear drum brake components. Refer to BR-41, "
Removal and Installation".
CAUTION:
Do not separate the brake tube from the wheel cylinders.
7. Remove the center muffler. Refer to EX-5, "
Exploded View".
8. Remove nuts (A) and remove center floor insulators.
9. Remove the bolts and remove the parking brake rear cables (RH/LH). CAUTION:
Do not excessively bend the parking brake cables.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the adjusting nut if the nut is removed.
• Inspect and adjust the rear brakes. Refer to BR-43, "
Inspection and Adjustment".
• Inspect and adjust the parking brake. Refer to PB-4, "
Inspection and Adjustment".
ALBIA1147ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

PARKING BRAKE SWITCHPB-9
< REMOVAL AND INSTALLATION >
C
DE
G H
I
J
K L
M A
B
PB
N
O P
PARKING BRAKE SWITCH
Removal and InstallationINFOID:0000000012430693
REMOVAL
1. Remove the center console assembly. Refer to PB-6, "Exploded View".
2. Disconnect the harness connector from the parking brake switch. Refer to PB-6, "
Exploded View".
3. Remove the screw and remove the parking brake switch. Refer to PB-6, "
Exploded View".
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the parking brake switch if it has been dropped or sustained an impact.
Adjust the parking brake cable if necessary. Refer to PB-4, "
Inspection and Adjustment".
Revision: August 2015 2016 Versa Note

cardiagn.com

PB-10
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Parking Brake ControlINFOID:0000000012430694
ItemStandard
Number of notches [under force of 196 N (20.0 kg-f, 44.1 lb-f)] 11 − 12 notches
Number of notches when brake warning light illuminates 1 notch
Revision: August 20152016 Versa Note

cardiagn.com

PCS
PCS-1
ELECTRICAL & POWER CONTROL
C
DE
F
G H
I
J
K L
B
SECTION PCS
A
O P
N
CONTENTS
POWER CONTROL SYSTEM
IPDM E/R
PRECAUTION ....... ........................................
3
PRECAUTIONS .............................................. .....3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
3
SYSTEM DESCRIPTION ..............................4
COMPONENT PARTS ................................... .....4
Component Parts Location .................................. ......4
SYSTEM ..............................................................5
RELAY CONTROL SYSTEM ................................ ......5
RELAY CONTROL SYSTEM : System Descrip-
tion ...................................................................... ......
5
RELAY CONTROL SYSTEM : Fail-safe ...................6
POWER CONSUMPTION CONTROL SYSTEM ... ......7
POWER CONSUMPTION CONTROL SYSTEM :
System Description ...................................................
8
DIAGNOSIS SYSTEM (IPDM E/R) ......................9
Diagnosis Description ......................................... ......9
CONSULT Function (IPDM E/R) .............................10
ECU DIAGNOSIS INFORMATION ..............13
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ............. ....
13
Reference Value ................................................. ....13
Fail-safe ..................................................................19
DTC Index ..............................................................20
WIRING DIAGRAM ......................................21
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ............. ....
21
Wiring Diagram ................................................... ....21
DTC/CIRCUIT DIAGNOSIS .........................26
U1000 CAN COMM CIRCUIT ...........................26
Description ........................................................... ....26
DTC Logic ................................................................26
Diagnosis Procedure ...............................................26
B2098 IGNITION RELAY ON STUCK ..............27
DTC Logic ................................................................27
Diagnosis Procedure ...............................................27
B2099 IGNITION RELAY OFF STUCK ............28
DTC Logic ................................................................28
Diagnosis Procedure ...............................................28
POWER SUPPLY AND GROUND CIRCUIT ....29
Diagnosis Procedure ...............................................29
REMOVAL AND INSTALLATION ...............30
IPDM E/R ...........................................................30
Exploded View ..................................................... ....30
Removal and Installation .........................................30
POWER DISTRIBUTION SYSTEM
PRECAUTION ...... ........................................
32
PRECAUTIONS .................................................32
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
32
SYSTEM DESCRIPTION .............................33
COMPONENT PARTS ......................................33
Component Parts Location .................................. ....33
SYSTEM ............................................................34
POWER DISTRIBUTION SYSTEM ........................ ....34
POWER DISTRIBUTION SYSTEM : System De-
scription ............................................................... ....
34
Fail-safe ...................................................................35
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS-2
DIAGNOSIS SYSTEM (BCM) ............................37
COMMON ITEM ..................................................... ...37
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) ....................................................
37
INTELLIGENT KEY ................................................ ...38
INTELLIGENT KEY : CONSULT Function (BCM -
INTELLIGENT KEY) ...............................................
38
ECU DIAGNOSIS INFORMATION ........... ...41
BCM, IPDM E/R .............................................. ...41
List of ECU Reference ......................................... ...41
WIRING DIAGRAM .....................................42
POWER DISTRIBUTION SYSTEM ................ ...42
Wiring Diagram .................................................... ...42
BASIC INSPECTION ...................................50
DIAGNOSIS AND REPAIR WORK FLOW ..... ...50
Work Flow ............................................................ ...50
PROCEDURE FOR TEMPORARILY DIS-
ABLING THE IGNITION BATTERY SAVER
SYSTEM .......................................................... ...
53
Description ........................................................... ...53
Work Procedure ......................................................53
DTC/CIRCUIT DIAGNOSIS ...................... ...54
U1000 CAN COMM CIRCUIT ......................... ...54
Description ........................................................... ...54
DTC Logic ...............................................................54
Diagnosis Procedure ..............................................54
U1010 CONTROL UNIT (CAN) .........................55
DTC Logic ............................................................ ...55
Diagnosis Procedure ..............................................55
B2614 ACC RELAY CIRCUIT ...........................56
DTC Logic ............................................................ ...56
Diagnosis Procedure ..............................................56
B2615 BLOWER RELAY CIRCUIT ...................58
DTC Logic ............................................................ ...58
Diagnosis Procedure ..............................................58
B2616 IGNITION RELAY CIRCUIT ...................60
DTC Logic ............................................................ ...60
Diagnosis Procedure ............................................ ...60
B2618 BCM .......................................................62
DTC Logic ............................................................ ...62
Diagnosis Procedure ...............................................62
B261A PUSH-BUTTON IGNITION SWITCH .....63
DTC Logic ............................................................ ...63
Diagnosis Procedure ...............................................63
B26F1 IGNITION RELAY ..................................65
DTC Logic ...............................................................65
Diagnosis Procedure ...............................................65
B26F2 IGNITION RELAY ..................................66
DTC Logic ...............................................................66
Diagnosis Procedure ...............................................66
B26F6 BCM .......................................................68
DTC Logic ............................................................ ...68
Diagnosis Procedure ...............................................68
PUSH-BUTTON IGNITION SWITCH .................70
Component Function Check ............................... ...70
Diagnosis Procedure ...............................................70
Component Inspection ............................................71
POWER SUPPLY AND GROUND CIRCUIT .....73
BCM ........................................................................ ...73
BCM : Diagnosis Procedure ....................................73
IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) ........................... ...
73
IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) : Diagnosis Pro-
cedure .....................................................................
73
SYMPTOM DIAGNOSIS ............................75
PUSH-BUTTON IGNITION SWITCH DOES
NOT OPERATE .............................................. ...
75
Description ........................................................... ...75
Diagnosis Procedure ...............................................75
REMOVAL AND INSTALLATION ..............76
BCM (BODY CONTROL MODULE) ............... ...76
Removal and Installation .........................................76
PUSH-BUTTON IGNITION SWITCH .............. ...77
Removal and Installation .........................................77
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS
PRECAUTIONSPCS-3
< PRECAUTION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental
Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012433266
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three mi nutes before performing any service.
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS-4
< SYSTEM DESCRIPTION >[IPDM E/R]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000012433267
1. IPDM E/R
A. Engine compartment (LH)
AWMIA1435ZZ
Revision: August 2015
2016 Versa Note

cardiagn.com

PCS
SYSTEMPCS-5
< SYSTEM DESCRIPTION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
SYSTEM
RELAY CONTROL SYSTEM
RELAY CONTROL SYSTEM
: System DescriptionINFOID:0000000012433268
SYSTEM DIAGRAM
DESCRIPTION
IPDM E/R activates the internal control circuit to perfo rm the relay ON-OFF control according to the input sig-
nals from various sensors and the request signals re ceived from control units via CAN communication.
CAUTION:
IPDM E/R integrated relays cannot be removed.
AWMIA1736GB
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS-6
< SYSTEM DESCRIPTION >[IPDM E/R]
SYSTEM
RELAY CONTROL SYSTEM : Fail-safe
INFOID:0000000012433269
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With ECM
If No CAN Communication Is Available With BCM
Control relay Input/outputTransmit unit Control part Reference page
• Headlamp low relay
• Headlamp high relay • Low beam request signal
• High beam request signal
BCM (CAN)
• Headlamp LO
• Headlamp HI EXL-8
Tail lamp relay
Position light request signal BCM (CAN) •Parking lamp
• Side marker lamp
• License plate lamp
• Tail lamp
EXL-11
Illuminations
INL-9
• Front wiper relay
• Front wiper high relayFront wiper request signal BCM (CAN)
Front wiper motorWW-8Front wiper stop position sig-
nal Front wiper motor
Starter control relay Starter control relay signal BCM (CAN)
Starter motorSTR-8
(without Intelli-
gent Key)
STR-9
(with Intelligent
Key)
Transmission range switch
signal (CVT models)
Transmission range
switch
Clutch interlock switch signal
(M/T models) Clutch interlock switch
• Cooling fan low relay
• Cooling fan high relay Cooling fan speed request sig-
nal
ECM (CAN)
Cooling fan EC-38
A/C relayA/C compressor request sig-
nal
ECM (CAN)A/C compressor
(Magnet clutch)
HAC-11
Ignition relay-1Ignition switch ON signal BCM (CAN)
Each control unit,
sensor, actuator and
relay (Ignition power
supply) EC-35Vehicle speed signal (Meter)
Combination meter
(CAN)
Push-button ignition switch
signal Push-button ignition
switch
Control part
Fail-safe operation
Cooling fan • The cooling fan relay turn ON when the ignition switch is turned ON (Cooling fan HI operation)
• The cooling fan relay turn OFF when the ignition switch is turned OFF
A/C compressor A/C relay OFF
Generator Outputs the power generation command signal (PWM signal) 0%
Control part Fail-safe operation
Headlamp • Turns ON the headlamp low relay when the ignition switch is turned ON
• Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
•Parking lamp
• Side marker lamp
• License plate lamp
• Illumination
• Tail lamp • Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
Revision: August 2015
2016 Versa Note

cardiagn.com

PCS
SYSTEMPCS-7
< SYSTEM DESCRIPTION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
IGNITION RELAY MALFUNCTION DETECTION FUNCTION
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
NOTE:
The tail lamp turns OFF when the ignition switch is turned ON.
FRONT WIPER CONTROL
IPDM E/R detects front wiper stop posit ion by a front wiper auto stop signal.
When a front wiper auto stop signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 second activation and 20 second stop five times.
NOTE:
This operation status can be confirmed on the IPDM E/ R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
POWER CONSUMPTIO N CONTROL SYSTEM
Front wiper motor • The status just before activation of fail-safe control is maintained until the ignition switch is
turned OFF while the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-safe control is activated while the front wiper is set in the INT mode and the front wiper motor is operating.
• Returns automatically wiper to stop position when ignition switch is turned ON if fail-safe control
is activated while front wiper motor is operated and wiper stop in the other position than stop
position.
Front fog lamp (if equipped) Front fog lamp relay OFF
Horn Horn OFF
Ignition relay The status just before activation of fail-safe is maintained.
Starter motor Starter control relay OFF
Control part
Fail-safe operation
DTCIgnition switch Ignition relayTail lamp relay
—O NON—
—O FFO FF—
B2098: IGN RELAY ON OFFONON (10 minutes)
B2099: IGN RELAY OFF ONOFF —
Ignition switch Front wiper switch Auto stop signal
ON OFF
Front wiper stop position signal cannot be
input 10 seconds.
ON The signal does not change for 10 seconds.
Revision: August 2015 2016 Versa Note

cardiagn.com