display NISSAN PATHFINDER 2012 R52 / 4.G 06IT Navigation Manual

OPERATING WITH THE BUTTONS ON
THE CONTROL PANEL
Push<ZOOM IN> or<ZOOM OUT> . A scale
appears on the left side of the screen.
To view the map in detail, push <ZOOM IN>.
To view a wider area, push <ZOOM OUT>.
The scale will automatically disappear when
neither <ZOOM IN> nor<ZOOM OUT> has
been pushed for several seconds.
If the scaling operation is not performed for a
specified period of time, the scale display
disappears.
INFO:
Free zoom:
Once the [Small Step Zoom by Dial] is set to ON
in the setting screen, the scale can be changed
in smaller steps when you push and hold
<ZOOM IN> or<ZOOM OUT> than when
you briefly push the button.
If you briefly push the button, the operation
returns to normal.
CHANGING THE SCALE OF A MAP
Map settings3-9

OPERATING WITH THE CENTER DIAL
1. Turn the center dial on the map screen. Themap scale is displayed.
2. Use the center dial to adjust the map scale.
&1Clockwise: Zoom in
&2Counterclockwise: Zoom out
INFO:
Free zoom:
Depending on the setting, using the center dial
to change the map scale may adjust the scale
normally, or it may engage the free zoom (finer
scale adjustment in smaller steps) .
“NAVIGATION SETTING” (page 8-4)
OPERATING WITH THE TOUCH OP-
ERATION
1. Touch.
Displays the scale.
2. Touch [ZOOM IN] or [ZOOM OUT] to
change the scale.
3-10Map settings

INFO:
Free zoom:
Once the [Small Step Zoom by Dial] is set to ON
in the setting screen, the scale can be changed
in smaller steps when you push and hold
[ZOOM IN] or [ZOOM OUT] than when you
briefly push the button.
If you briefly push the button, the operation
returns to normal.
Voice command
1. Push <TALK> located on the steering
switch.
2. After the tone sounds, speak a command.
To change the map scale:
“Zoom In” (Alternate command mode)
“Zoom Out” (Alternate command mode)
MAP SCALE
The following scales are available depending on
the map view. . In Plan View:
Widest (1/51,200,000) to the most detailed
(1/2,500)
. In Birdview
TM:
Widest (1/20,480,000) to the most detailed
(viewpoint height at 1/3,000)
Scale level of the Plan View display
Map scale Actual distance
Normal Map 1:51.2 million
400 miles
(640 km)
1:5.12 million 32 miles (64 km)
1:1.28 million 8 miles (16 km) 1:800,000 5 miles (10 km)
1:320,000 2 miles (4 km)
1:160,000 1 mile (2 km)1:80,000 1/2 mile (1 km)
1:40,000 1/4 mile (500 m)
1:20,000 1/8 mile (200 m)
1:10,000 300 ft (100 m)1:5,000 150 ft (50 m)
Building
footprint
graphics 1:5,000 150 ft (50 m)
1:2,500
75 ft (25 m)
Example: The most detailed level
Example: The widest level
Map settings3-11

Scale level of the BirdviewTMdisplay
Map scaleDistance be-
tween grids
Normal Map 1:20.48 million
160 miles
(256 km)
1:5.12 million 32 miles (64 km)
1:2.56 million 16 miles (32 km)
1:1.28 million 8 miles (16 km) 1:640,000 4 miles (8 km)
1:320,000 2 miles (4 km)
1:160,000 1 mile (2 km)1:80,000 1/2 mile (1 km)
1:40,000 1/4 mile (500 m)
1:25,000 1/6 mile (250 m)
3D building
graphics 1:6,000 180 ft (60 m)
1:3,000
90 ft (30 m)
Example: The most detailed level
Example: The widest level
INFO:
The traffic information icons are not displayed on
the map screen when the map scale is set to 1/4
mile (500 m) or higher in Plan View, to 1 mile (2
km) or higher in Birdview
TM, to the building
footprint graphics (Plan View) , or the 3D
building graphics (Birdview
TM).“Traffic information can be displayed in the
following scale levels” (page 7-8) Other settings are also available for the map
screen, such as switching the map view,
changing the map direction, splitting the screen,
etc.
SWITCHING THE MAP VIEW
The map view can be changed between Plan
View and BirdviewTM. The map can also be
displayed in the split screen mode.
1. Push <ENTER> while the current location
map screen is displayed.
OTHER SETTINGS FOR THE MAP
SCREEN
3-12Map settings

2. Highlight [Map Settings] and push<ENTER> .
3. Highlight [Change View] and push the right
button of the directional buttons.
4. Highlight the preferred map view and push <ENTER> . The indicator of the selected
map view illuminates.
5. Push <MAP>or touch [Back to Map] to
return to the current location map screen.
Available views
. Plan View:
Switches to Plan View.
. Birdview
TM:
Switches to BirdviewTM.
. Split (Plan View):
Changes to the split screen mode and both
halves display maps in Plan View.
. Split (Birdview
TM):
Changes to the split screen mode and the
left half displays the map in Plan View and
the right half displays the map in Birdview
TM.
INFO:
. When you select [Split (Plan View)] or [Split
(Birdview
TM)], [Left Settings] and [Right
Settings] become available. This is used to
operate the left/right screen.
“OPERATION WITH SPLIT SCREEN
DISPLAY” (page 3-18)
. If [Split (Plan View)] or [Split (Birdview
TM)] is
selected, the normal map scrolling and scale
adjustment are set in the right screen.
However, if you touch an icon before
adjusting the map direction or scale, then
each screen can be adjusted independently.
Split (Plan View)
Split (BirdviewTM)
Map settings3-13

Other settings
You can also set the map view using the
following procedure.
1) Push<SETTING> .
2) Highlight [Navigation] and push <ENTER>.
3) Highlight [Map Settings] and push <ENTER> .
Voice command
1. Push <TALK> located on the steering
switch.
2. After the tone sounds, speak a command. . To display a map in Plan View:
“Plan View map” (Alternate command mode)
. To display a map in Birdview
TM:
“Birdview map” (Alternate command mode) .
To display a split map in Plan View:
“Plan View Split Map” (Alternate command
mode)
. To display a split map in Birdview
TM:
“Birdview Split Map” (Alternate command
mode)
SETTINGS OF HEADING/LONG
RANGE MAP VIEW
You can change the map direction (orientation)
in Plan View or change the position of the
vehicle icon to view a wider area in the traveling
direction.
These settings are available only in the Plan
View or Split (Plan View) mode.
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map Settings] and push
<ENTER> .
3. Highlight [Settings] and push <ENTER>.
3-14Map settings

4. Highlight the preferred map orientation andpush <ENTER> . The indicator of the
selected map orientation illuminates.
5. Push <MAP>to return to the current
location map screen.
Available map orientations
. North Up:
North is set at the top of the map.
. Heading Up:
The traveling direction is set at the top of the
map.
. Long Range Map View:
The vehicle icon is located slightly lower
than the center of the screen. This offers a
wider view in the traveling direction.
. Map Scale:
A scale appears on the left side of the
screen. This changes the scale of a map. .
Birdview
TMAngle:
This changes the BirdviewTMangle.
INFO:
. [Long Range] is displayed only when you
select [Heading Up].
. [Birdview Angle] is displayed only when the
map view is set to the Birdview
TMor Split
(BirdviewTM) mode.
North Up
Heading Up
Long Range Map View
INFO:
If the map orientation is switched, the icon
displayed in the lower left corner is also
switched.
: North Up
: Heading Up
Map settings3-15

Other settings
You can also set the orientation of the map using
the following procedure.
1) Push<SETTING> .
2) Highlight [Navigation] and push <ENTER>.
3) Highlight [Map Settings] and push <ENTER> .
4) Highlight [Settings] and push <ENTER>.
INFO:
Touching the icon on the map can also change
the direction of the map.
Voice command
1. Push <TALK> located on the steering
switch.
2. After the tone sounds, speak a command.
To charge the map direction:
“North Up” (Alternate command mode)
“Heading Up” (Alternate command mode)
CHANGING THE BirdviewTMANGLE
This changes the BirdviewTMangle.
This setting is available only in the BirdviewTMor
Split (BirdviewTM) mode.
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map settings] and push
<ENTER> .
3. Highlight [Settings] and push <ENTER>.
3-16Map settings

OPERATION WITH SPLIT SCREEN
DISPLAY
When the split screen is displayed, you can
operate the left/right screen.
1. Push<ENTER> while the current location
map screen is displayed.
2. Highlight [Map Settings] and push <ENTER> .
3. Highlight [Left Settings] or [Right Settings]
and push <ENTER> .
4. Highlight the preferred map view and push
<ENTER> . The indicator of the selected
map view illuminates.
5. Push <MAP>to return to the current
location map screen.
Available map orientations
. North Up:
North is set at the top of the map.
. Heading Up:
The traveling direction is set at the top of the
map.
. Long Range:
The vehicle icon is located slightly lower
than the center of the screen. This offers a
wider view in the traveling direction.
. Map Scale:
A scale appears on the left side of the
screen. This changes the scale of a map.
. Birdview
TMAngle:
This changes the BirdviewTMangle.
3-18Map settings

Other settings
You can also change the scale of the left screen
using the following procedure.
1) Push<SETTING> .
2) Highlight [Navigation] and push <ENTER>.
3) Highlight [Map Settings] and push <ENTER> .
4) Highlight [Left Settings] or [Right Settings] and push <ENTER> . You can display icons on the map and view
information about destinations or landmarks.
DISPLAYING LANDMARK ICONS
This allows you to display or hide the landmark
icons by type.
Landmark icons that can be displayed
.Restaurant
.
Gas Station
.
Hotel
.
AT M
.
Rest Area
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Landmark Icons] and push <ENTER> .
LOOKING AT INFORMATION ON
THE MAP
Map settings3-19