NISSAN PICK-UP 1998 Repair Manual

SBT453
SEAT
Front Seat (Cont'd)
BT-31

Heated Seat
lWhen handling seat, be extremely careful not to scratch heating unit.
lTo replace heating unit, seat trim and pad should be separated.
lDo not use any organic solvent, such as thinner, benzene, alcohol, gasoline, etc. to clean trims.
Seatback heating unit removal & installation
.For Wiring Diagram, refer to ``HEATED SEAT'' in EL section.
SBF424H
SEAT
BT-32

Rear Seat
SBT454
SEAT
BT-33

Jump Seat
SBT637
SEAT
BT-34

SBT456
SUNROOF
BT-35

REMOVAL
After removing moldings, remove glass using piano wire or
power cutting tool and an inflatable pump bag.
WARNING:
When cutting the glass from the vehicle, always wear safety
glasses and heavy gloves to help prevent glass splinters
from entering your eyes or cutting your hands.
CAUTION:
lBe careful not to scratch the glass when removing.
lDo not set or stand the glass on its edge. Small chips
may develop into cracks.
INSTALLATION
lUse a genuine Nissan Urethane Adhesive Kit or equiva-
lent and follow the instructions furnished with it.
lWhile the urethane adhesive is curing, open a door win-
dow. This will prevent the glass from being forced out by
passenger compartment air pressure when a door is
closed.
lThe molding must be installed securely so that it is in
position and leaves no gap.
lInform the customer that the vehicle should remain sta-
tionary until the urethane adhesive has completely cured
(preferably 24 hours). Curing time varies with tempera-
ture and humidity.
WARNING:
lKeep heat and open flames away as primers and adhe-
sive are flammable.
lThe materials contained in the kit are harmful if
swallowed, and may irritate skin and eyes. Avoid contact
with the skin and eyes.
lUse in an open, well ventilated location. Avoid breathing
the vapors. They can be harmful if inhaled. If affected by
vapor inhalation, immediately move to an area with fresh
air.
lDriving the vehicle before the urethane adhesive has
completely cured may affect the performance of the
windshield in case of an accident.
CAUTION:
lDo not use an adhesive which is past its usable term.
Shelf life of this product is limited to six months after the
date of manufacture. Carefully adhere to the expiration
or manufacture date printed on the box.
lKeep primers and adhesive in a cool, dry place. Ideally,
they should be stored in a refrigerator.
lDo not leave primers or adhesive cartridge unattended
with their caps open or off.
lThe vehicle should not be driven for at least 24 hours or
until the urethane adhesive has completely cured. Cur-
ing time varies depending on temperature and humidi-
ties. The curing time will increase under higher tempera-
tures and lower humidities.
SBF034B
SBT472
SBT473
WINDSHIELD AND WINDOWS
BT-36

Windshield
REPAIRING WATER LEAKS FOR WINDSHIELD
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between urethane adhesive material and body or glass, determine the extent of
leakage. This can be done by applying water to the windshield area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
SBT457-A
WINDSHIELD AND WINDOWS
BT-37

Side Window
REMOVE Ð Side window
V1Remove screws.
V2Remove rear pillar finisher. Refer to ``Side and Floor Trim'' (King cab model) for details, BT-15.
V3Remove nuts securing side window, then remove side window assembly.
SBT638
WINDSHIELD AND WINDOWS
BT-38

Door MirrorCAUTION:
Be careful not to scratch door rearview mirror body.
.For Wiring Diagram, refer to ``POWER DOOR MIRROR'' in EL section.
REMOVAL Ð Door mirror
V1Remove door trim. Refer to ``Door Trim'' for details, BT-18.
V2Remove inner cover from front corner of door.
V3Disconnect door mirror harness connector.
V4Remove bolts securing door mirror, then remove door mirror assembly.
SBT458
MIRROR
BT-39

Removal
CAB BODY
lRemove the following parts in engine compartment at least.
(1) Main harness and other wiring harnesses
lDisconnect brake and clutch line in engine compartment.
lRemove the following parts from underbody at least.
(1) Transmission and transfer control levers
(2) Parking brake control lever and cables
(3) Main harness and other wiring harnesses
REAR BODY
lRemove the following parts at least.
(1) Rear combination lamp and license plate lamp harness
(2) Fuel filler tube fixing screws
SBF348C
ABT189
CAB AND REAR BODY
BT-40