Connector NISSAN TEANA 2003 Service Manual

BRC-78
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM

3. CHECK STOP LAMP SWITCH CIRCUIT
1. Turn ignition switch OFF and disconnect ABS actuator and elec-
tric unit (control unit) harness connectors.
2. Check voltage between the ABS actuator and electric unit (con-
trol unit) harness connector E241 terminal 23 and ground.
OK or NG
OK >> Connect connector securely and perform self-diagnosis again.
NG >> Stop lamp switch circuit malfunction. Repair the circuit.
ABS Actuator and Electric Unit (Control Unit) Power Supply and Ground Sys-
tem
BFS000EG
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Check the self-diagnostic results.
Is above displayed on self-diagnosis display?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Turn ignition switch OFF, disconnect the ABS actuator and electric unit (control unit) harness connector,
and check terminal for deformation, disconnection, looseness, and so on. If there is a malfunction, repair
or replace the terminal.
2. Securely reconnect connectors and perform self-diagnosis again.
OK or NG
OK >> Connector terminal contact is loose, damaged, open or shorted.
NG >> GO TO 3.
SFIA2104E
ABS actuator and electric unit (control unit) Ground Measurement condition Voltage
23 —Brake pedal depressedBattery voltage
(Approx. 12 V)
Brake pedal not depressed Approx. 0 V
Self-diagnostic results
BATTERY VOLTAGE [ABNORMAL]

TROUBLE DIAGNOSIS FOR SYSTEM
BRC-79
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

3. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER AND GROUND CIRCUIT
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector E241.
2. Check voltage between ABS actuator and electric unit (control
unit) harness connector E241 terminal 45 and ground with igni-
tion switch turned ON and OFF.
3. Check continuity between ABS actuator and electric unit (control
unit) harness connector E241 terminals 31, 46 and ground.
OK or NG
OK >> Check battery for loose terminal and low voltage mal-
function. Repair if there is a malfunction.
NG >> Corresponding harness circuit malfunction. Repair the
circuit.
SFIA2113E
ABS actuator and electric unit (control unit) Ground Measurement condition Voltage
45 —Ignition switch ONBattery voltage
(Approx. 12 V)
Ignition switch OFF Approx. 0 V
ABS actuator and electric unit (contorl unit) Ground Continuity
31, 46 — Yes
SFIA2114E

BRC-80
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM

Brake Fluid Level Switch SystemBFS000EH
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
1. Check fluid level in brake fluid reservoir tank. If the level is low, add brake fluid.
2. Check the self-diagnostic results.
Is above displayed on self-diagnosis display?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Turn ignition switch OFF, disconnect ABS actuator and electric unit (control unit) connector and brake fluid
level switch, and check terminal for deformation, disconnection, looseness, and so on. Repair or replace if
there is a malfunction.
2. Securely reconnect connectors and perform self-diagnosis again.
OK or NG
OK >> Connector terminal contact was loose, damaged, open or shorted.
NG >> GO TO 3.
3. CHECK HARNESS BETWEEN BRAKE FLUID LEVEL SWITCH AND ABS ACTUATOR AND ELEC-
TRIC UNIT (CONTROL UNIT)
1. Disconnect ABS actuator and electric unit (control unit) connec-
tor.
2. Check continuity between ABS actuator and electric unit (control
unit) harness connector E241 and brake fluid level switch con-
nector E52.
OK or NG
OK >> Connect connector securely and perform self-diagnosis
again.
NG >> If open or short in harness, repair or replace the har-
ness.
Self-diagnostic results
BR FLUID LEVEL LOW
ABS actuator and electric unit
(control unit)Brake fluid level switch Continuity
38 1 Yes
38 Ground No
Ground 2 Yes
SFIA2105E

TROUBLE DIAGNOSIS FOR SYSTEM
BRC-81
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

CAN Communication SystemBFS000EI
Inspection Procedure
1. CHECK CONNECTOR
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector and steer-
ing angle sensor connector. Check terminal for deformation, disconnection, looseness, and so on. If any
malfunction is found, repair or replace terminal.
2. Securely reconnect connectors and perform self-diagnosis.
Is above displayed in the self-diagnosis item?
YES >> Print out self-diagnostic results and go to LAN-49, "CAN System Specification Chart" .
NO >> Connector terminal connection is loose, damaged, open or shorted.
Component Parts InspectionBFS000EJ
VDC OFF SWITCH

Turn ignition switch OFF, and disconnect the VDC OFF switch
connector, and check continuity between terminals 1 and 2.
Self-diagnostic results
CAN COMM CIRCUIT
ST ANG SEN COM CIR
1 - 2 : Continuity should exist when pushing
switch.
Continuity should not exist when releasing
switch.
SFIA2519E

BRC-82
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYMPTOMS

TROUBLE DIAGNOSIS FOR SYMPTOMSPFP:00007
Excessive ABS Function Operation FrequentlyBFS000EK
1. CHECK START
Check longitudinal brake force distribution using a brake tester. Refer to BR-40, "
SERVICE DATA AND SPEC-
IFICATIONS (SDS)" .
OK or NG
OK >> GO TO 2.
NG >> Check brake system.
2. CHECK FRONT AND REAR AXLE
Make sure that there is no marked “play” in the front or rear axles. Refer to FA X - 5 , "
WHEEL BEARING
INSPECTION" (Front), RAX-3, "WHEEL BEARING INSPECTION" (Rear).
OK or NG
OK >> GO TO 3.
NG >> Repair.
3. CHECK WHEEL SENSOR AND SENSOR ROTOR
Check wheel sensor and sensor rotor for the following.

Sensor installation for damage

Sensor rotor installation for damage

Sensor connector connection

Sensor harness inspection
OK or NG
OK >> GO TO 4.
NG >>

Replace sensor or sensor rotor.

Repair harness.
4. CHECK ABS WARNING LAMP DISPLAY
Make sure that the warning lamp turns off approximately 1 second after the ignition switch is turned ON or
when driving.
OK or NG
OK >> Normal
NG >> Perform self-diagnosis. Refer to BRC-58, "
Self-Diagnosis" .

TROUBLE DIAGNOSIS FOR SYMPTOMS
BRC-83
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

Unexpected Pedal ReactionBFS000EL
1. CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to BR-6, "
Inspection and Adjustment" .
Is the stroke too big?
YES >>
Bleed air from the brake piping. Refer to BR-10, "Bleeding Brake System" .

Check brake pedal, brake booster, and master cylinder mount for play, looseness, and brake
system fluid leakage, etc. Repair if necessary. Refer to Brake pedal: BR-7, "
COMPONENTS" ,
brake booster and master cylinder: BR-22, "
COMPONENTS" .
NO >> GO TO 2.
2. CHECK FUNCTION
Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS. Check if braking force is
normal in this condition. Connect connector after inspection.
OK or NG
OK >> GO TO 3. Check Wheel Sensor and Sensor Rotor. Refer to BRC-82, "Excessive ABS Function
Operation Frequently" .
NG >> Check brake system.
Longer Stopping DistanceBFS000EM
CAUTION:
The stopping distance on slippery road surfaces might be longer with the ABS operating than when
the ABS is not operating.
1. CHECK FUNCTION
Turn ignition switch OFF. Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS.
In this condition, check stopping distance. After inspection, connect connector.
OK or NG
OK >> GO TO 3. Check Wheel Sensor and Sensor Rotor. Refer to BRC-82, "Excessive ABS Function
Operation Frequently" .
NG >>

Bleed air from the brake piping. Refer to BR-10, "Bleeding Brake System" .

Check brake system.

TROUBLE DIAGNOSIS FOR SYMPTOMS
BRC-85
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

Vehicle Jerks During VDC/TCS/ABS ControlBFS000EP
1. SYMPTOM CHECK
Check if the vehicle jerks during VDC/TCS/ABS control.
OK or NG
OK >> Normal
NG >> GO TO 2.
2. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnostic of ABS actuator and electric unit (control unit).
Are self-diagnostic results indicated?
YES >> Check the corresponding items, make repairs, and perform ABS actuator and electric unit (control
unit) self-diagnosis.
NO >> GO TO 3.
3. CHECK CONNECTOR
1. Turn ignition switch OFF, disconnect the ABS actuator and electric unit (control unit) connector and check
the terminal for deformation, disconnection, looseness, and so on. Repair or replace, if there is a malfunc-
tion.
2. Securely connect connectors. Perform ABS actuator and electric unit (control unit) self-diagnosis.
Are self-diagnostic results indicated?
YES >> If poor contact, damage, open or short circuit of connector terminal is found, repair or replace.
NO >> GO TO 4.
4. CHECK ECM AND TCM SELF-DIAGNOSTIC RESULTS
Perform ECM and TCM self-diagnosis.

ECM self-diagnosis: Refer to EC-394, "TROUBLE DIAGNOSIS" .

TCM self-diagnosis: Refer to AT- 3 4 , "TROUBLE DIAGNOSIS" or CVT-24, "TROUBLE DIAGNOSIS" .
Are self-diagnostic results indicated?
YES >> Check the corresponding items, make repairs.
NO >> Replace ABS actuator and electric unit (control unit).

BRC-88
[VDC/TCS/ABS]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)

ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)PFP:47660
Removal and InstallationBFS000ES
COMPONENTS
1. From master cylinder secondary side 2. To front RH caliper 3. To rear LH caliper
4. To rear RH caliper 5. To front LH caliper 6. From master cylinder primary side
7. Connector 8. ABS actuator and electric unit (con-
trol unit)9. Bracket
SFIA2515E

ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
BRC-89
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

REMOVAL
1. Disconnect ABS actuator and electric unit (control unit) connector.
2. Loosen brake tube flare nuts, then remove brake tubes from ABS actuator and electric unit (control unit).
3. Remove ABS actuator and electric unit (control unit) mounting nuts.
4. Remove ABS actuator and electric unit (control unit) from vehicle.
CAUTION:
Be careful of the following when removing ABS actuator and electric unit (control unit).

If the part number on the part number label (pasted on actuator upper surface) is the same, ABS
actuator and electric unit (control unit) cannot be used on another vehicle.
If it is used on another vehicle, ABS warning lamp, SLIP indicator lamp and VDC OFF indicator
lamp may turn ON or VDC/TCS/ABS may not operate normally.
When replacing ABS actuator and electric unit (control unit), must use new service parts.

Before servicing, disconnect battery cables.

To remove brake tube, use a flare nut torque wrench to prevent flare nuts and brake tube from
being damaged. To install, use a flare nut torque wrench (commercial service tool) and tighten
with the specified torque.

Do not apply excessive impact to actuator, such as dropping it.

Do not remove and install ABS actuator and electric unit (control unit) by holding harness.
INSTALLATION
Install is in the reverse order of the removal.
CAUTION:
Be careful of the following when installing ABS actuator and electric unit (control unit).

Tighten the mounting bolts and nuts with the specified torque.

After the work, bleed air from brake piping. Refer to BR-10, "Bleeding Brake System" .

After installing body harness connector in the actuator, make sure connector is securely locked

When replacing ABS actuator and electric unit (control unit), calibrate Steering angle sensor neu-
tral position. Refer to BRC-40, "
Adjustment of Steering Angle Sensor Neutral Position" .

BRC-90
[VDC/TCS/ABS]
G SENSOR

G SENSORPFP:47930
Removal and InstallationBFS000ET
REMOVAL
CAUTION:

Do not drop or strike G sensor, because it has little endurance to impact.

Do not power tool etc., because G sensor is weak for the impact.
1. Remove center console. Refer to IP-14, "
(J) Center Console" , “INSTRUMENT PANEL ASSEMBLY”.
2. Disconnect G sensor harness connector.
3. Remove G sensor mounting bolts. Then remove yaw rate/side/
decel G sensor.
INSTALLATION
Installation is the reverse order of the removal.
CAUTION:
Do not drop or strike G sensor, because it has little endurance to impact.
SFIA2108E