NISSAN TEANA 2003 Service Manual

HOOD
BL-13
C
D
E
F
G
H
J
K
L
MA
B
BL

HOODPFP:F5100
Fitting AdjustmentBIS000VP
LONGITUDINAL AND LATERAL CLEARANCE ADJUSTMENT
1. Remove hood lock, loosen the hood hinge nuts and close the hood.
2. Adjust the lateral and longitudinal clearance, and open the hood to tighten the mounting bolts to the spec-
ified torque.
3. Install the hood lock temporarily, and align the hood striker and lock so that the centers of striker and lock
become vertical viewed from the front, by moving the hood lock laterally.
4. Tighten hood lock mounting bolts to the specified torque.
FRONT END HEIGHT ADJUSTMENT
1. Remove the hood lock and adjust the height by rotating the bumper rubber until the hood becomes 1 to1.5
mm (0.04 to 0.059 in) lower than the fender.
2. Temporarily tighten the hood lock, and position it by engaging it with the hood striker. Check the lock and
striker for looseness, and tighten the hood lock mounting bolts to the specified torque.
CAUTION:
Adjust right/left clearance between hood and each part to the following specification.
1. Hood hinge 2. Nut 3. Hood stay
4. Hood lock 5. Bolt
PIIB1752E
Hood (B) - Headlamp (B) : Less than 1.5 mm (0.059 in)
Hood (C) - fender (C) : Less than 1.0 mm (0.039 in)

BL-14
HOOD

SURFACE HEIGHT ADJUSTMENT
1. Remove hood lock, and adjust the surface height difference of hood, fender and headlamp according to
the fitting standard dimension, by rotating RH and LH bumper rubbers.
2. Install hood lock temporarily, and move hood lock laterally until the centers of striker and lock become ver-
tical when viewed from the front.
3. Check that the hood lock secondary latch is properly engaged
with the secondary striker with hood's own weight.
4. Check that the hood lock primary latch is securely engaged with
the hood striker with hood's own weight by dropping hood from
approx. 200 mm (7.87) height.
CAUTION:
Do not drop hood from a height of 300 mm (11.81 in) or
more.
5. Move hood lockup and down until striker smoothly engages the
lock when the hood is closed.
6. When pulling the hood opener lever gently, make sure that front
end of the hood rises by approximately 20 mm (0.79) and that hood striker and hood lock primary latch is
disengaged. Also make sure that hood opener returns to the original position.
7. After adjustment, tighten lock bolts to the specified torque.
Removal and InstallationBIS000VQ
Hood (B) - Headlamp (B) : 0.75 ± 1.8 mm (0.030 ± 0.071 in)
Hood (C) - fender (C) : 0 ± 1.0 mm (0 ± 0.039 in)
PIIB0259E
1. Hood assembly 2. Hood stay 3. Hood hinge
4. Hood lock 5. Washer hose 6. Hood insulator
7. Radiator core seal rubber
PIIB0260E

HOOD
BL-15
C
D
E
F
G
H
J
K
L
MA
B
BL

REMOVAL
Hood Assembly
1. Support the hood striker with a proper material to prevent it from
falling.
WARNING:
Body injury may occur if no supporting rod is holding the
hood open when removing the hood stay.
2. Disconnect washer hose at the connecting point.
3. Remove the hood stays from the stud balls on the body side.
4. Remove hinge nuts on hood and remove hood assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
INSTALLATION

Install in the reverse order of removal.

Apply Anti-Corrosion or equivalent to the attaching portion of hood hinge, hood ledge, and hood assembly.

After installing, perform hood fitting adjustment. Refer to BL-13, "Fitting Adjustment" .
PIIB0261E
: 12.7 N·m (1.3 kg-m, 9 ft-lb)
PIIB0262E

BL-16
HOOD

Removal and Installation of Hood Lock ControlBIS000VR
REMOVAL
Hood Lock and Hood Lock Cable
1. Remove hood lock bolts.
2. Disconnect hood lock cable from hood lock.
3. Remove fender protector (LH). Refer to EI-23, "
FENDER PRO-
TECTOR" .
4. Remove hood lock cable clips, from radiator core upper support
and hood ledge.
5. Remove hood opener and grommet on lower dashboard.
6. Pull out hood lock cable toward passenger room.
CAUTION:
While pulling the cable, be careful not to damage (peel) outer surface of the cable on edges of
body through hole.
INSTALLATION
Install in the reverse order of removal.
1. Pull the hood lock cable through the panel hole to the engine
compartment.
CAUTION:
Be careful not to bend the cable too much, keeping the
radius 100 mm (3.94 in) or more.
2. Make sure that the cable is not offset from the positioning grommet, and push the grommet into the panel
hole securely.
3. Apply sealant (POS seal) to area on the grommet indicated with the * mark.
1. Hood lock cable 2. Hood lock
PIIB1753E
: 23.6N·m (2.4 kg-m, 18 ft-lb)
PIIB1754E
PIIA0173E

HOOD
BL-17
C
D
E
F
G
H
J
K
L
MA
B
BL

4. Install cable securely to the lock.
5. After installing, check hood lock adjustment and hood opener
operation.
6. After installing, perform hood fitting adjustment. Refer to BL-13,
"Fitting Adjustment" .
Hood Lock Control InspectionBIS000VS
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Make sure that the hood lock secondary latch is properly
engaged with the secondary striker with hood's own weight.
2. Make sure that the hood lock primary latch is securely engaged
with the hood striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
CAUTION:
Do not drop hood from a height of 300 mm (11.81) or more.
3. When pulling hood opener lever gently, make sure that front end of the hood rises by approximately 20
mm (0.79in) and that hood striker and hood lock primary latch are disengaged. Also make sure that hood
opener returns to the original position.
4. Confirm hood lock is properly lubricated. If necessary, apply
grease at the point shown in the figure.
PIIB1755E
PIIB0259E
PIIB1334E

BL-18
RADIATOR CORE SUPPORT

RADIATOR CORE SUPPORTPFP:62500
Removal and InstallationBIS000VT
REMOVAL
1. Remove front bumper. Refer to EI-14, "FRONT BUMPER" .
2. Remove head lamp (LH/RH). Refer to LT- 3 6 , "
Removal and Installation" (Xenon type), LT- 6 2 , "Removal
and Installation" (Conventional type)
3. Remove air duct clips, and then remove air duct.
4. Remove crash zone sensor. Refer to SRS-44, "
CRASH ZONE SENSOR" .
5. Remove hood lock assembly, and then hood lock cable. Refer to BL-16, "
Removal and Installation of
Hood Lock Control" .
6. Remove ambient sensor. Refer to ATC-109, "
AMBIENT SENSOR" .
7. Remove hydraulic piping clips and tabs. Refer to PS-39, "
HYDRAULIC LINE" .
8. Remove radiator core support lower harness clips and mounting bolts, and then remove radiator core sup-
port lower. Remove mounting bolts with power tool.
9. Disconnect horn connectors and remove harness clips.
10. Remove each harness clip and nuts of radiator core support. Remove nuts with power tool.
11. Remove condenser mounting bracket bolts.
1. Radiator core support side (RH) 2. Air guide (RH) 3. Bolt
4. Nut 5. Radiator core support lower 6. Nut
7. Radiator core support center 8. Bolt 9. Horn (High)
10. Horn (Low) 11. Clip 12. Air guide (LH)
13. Radiator core support side (LH) 14. Radiator core support upper 15. Nut
16. Bolt 17. Bolt
PIIB0266E

RADIATOR CORE SUPPORT
BL-19
C
D
E
F
G
H
J
K
L
MA
B
BL

12. Remove radiator core support upper, side, and center as a single piece. Remove mounting bolts and nuts
with power tool.
13. After removing radiator core support upper, side, and center as a single piece, separate the following
parts.

Horns (High/Low)

Air guides (LH/RH)

Radiator core support side (LH/RH)

Radiator core upper support

Radiator core support center
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installing, check the hood adjustment and hood opener operation. Refer to BL-17, "
Hood Lock
Control Inspection" .

BL-20
FRONT FENDER

FRONT FENDERPFP:63100
Removal and InstallationBIS000VU
REMOVAL
1. Remove the front bumper. Refer to EI-14, "FRONT BUMPER" .
2. Remove fender protector mounting clips and screws from out side. Refer to EI-23, "
FENDER PROTEC-
TOR" .
3. Remove center mud guard. Refer to EI-24, "
CENTER MUD GUARD" .
4. Remove bolts securing radiator core support side.
5. Remove hood hinge cover (rubber). Refer to EI-21, "
COWL TOP" .
6. Remove side turn signal lamp.
7. Remove bolts, and then remove front fender.
CAUTION:
While removing use a shop cloth to protect body from damaging.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

After installing, apply touch-up paint (the body color) onto the head of the front fender mounting
bolts.

After installing, check front fender adjustment. Refer to BL-13, "Fitting Adjustment" and BL-119,
"Fitting Adjustment" .
1. Bolt 2. Front fender
PIIB0267E

POWER DOOR LOCK SYSTEM
BL-21
C
D
E
F
G
H
J
K
L
MA
B
BL

POWER DOOR LOCK SYSTEMPFP:24814
Component Parts and Harness Connector LocationBIS000VV
1. BCM M3,M4,M5 2. Door lock and unlock switch D6,D7 3. Key switch M20
(with intelligent key)
Key switch M34
(without intelligent key)
4. Front door lock actuator D24
(Driver side)5. Rear door lock actuator (LH) D52 6. Front door switch B10
(Driver side)
PIIB8744E

BL-22
POWER DOOR LOCK SYSTEM

System DescriptionBIS000VW
Power is supplied at all times

through 50A fusible link (letter M , located in the fuse and fusible link box)

to BCM terminal 55.

through 15A fuse [No. 17, located in the fuse block (J/B)]

to BCM terminal 42.

to key switch terminal 1 (without intelligent key system)

through 15A fuse [No. 18, located in the fuse block (J/B)]

to key switch terminal 3 (with intelligent key system)
When key switch is ON (key is inserted in ignition key cylinder), power is supplied

through key switch terminal 4 (without intelligent key system) or 8 (with intelligent key system)

to BCM terminal 37.
Ground is supplied

to BCM terminal 52

through body grounds M71 and M72.

to power window main switch (door lock and unlock switch) terminal 17

through body grounds M71 and M72.

to front door lock assembly (driver side) (door unlock sensor) terminal 5

through body grounds M71 and M72.
LOCK OPERATION
When the door is locked with power window main switch (door lock and unlock switch)
Ground is supplied

to BCM terminal 60

through power window main switch (door lock and unlock switch) terminal 18

through power window main switch (door lock and unlock switch) terminal 17

through body grounds M71 and M72.
When the driver side door locked with hand or key cylinder
Ground is intercepted

to BCM terminal 7.
When you meet either the above-mentioned
Power is supplied

through BCM terminal 50

to each door lock actuators terminal 3
Ground is supplied

to each door lock actuators terminal 2

through BCM terminal 51.
Each door lock actuator locks the door lock.
UNLOCK OPERATION
When the door is unlocked with power window main switch (door lock and unlock switch)
Ground is supplied

to BCM terminal 61

through power window main switch (door lock and unlock switch) terminal 6

through power window main switch (door lock and unlock switch) terminal 17

through body grounds M71 and M72.
When the driver side door unlocked with hand or key cylinder
Ground is supplied

to BCM terminal 7

through front door lock assembly (driver side) (door unlock sensor) terminal 4

through front door lock assembly (driver side) (door unlock sensor) terminal 5