NISSAN TEANA 2008 Owner's Guide

AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-25
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
EXIT ASSIST FUNCTION : Component Parts LocationINFOID:0000000003859813
1. BCM M118, M119, M122, M123 2. Combination meter M34 3. Key slot M99
4. Seat memory switch D13 5. Front door switch (driver side) B34 6. Reclining motor (driver side) B454
7. Lifting motor (front) (driver side)
B4558. Driver seat control unit B451,B4529.Sliding motor (driver side) B461
JMJIA1811ZZ

ADP-26
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
EXIT ASSIST FUNCTION : Component Description
INFOID:0000000003759083
CONTROL UNITS
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
ENTRY ASSIST FUNCTION
10. Lifting motor (rear) (driver side) B45611. Power seat switch (driver side) B459
(sliding, lifting switch)12. Power seat switch (driver side) B459
(reclining switch)
13. TCM (transmission control module)
F2314. Control device (detention switch)
M5715. ABS actuator and electric unit (con-
trol unit) E36
A. Behind the combination meter B. View with seat cushion and seatback
pad removedC. Back side of the seat cushion
D. Engine room (LH) E. View with the center console assem-
bly removedF. Engine room (RH)
Item Function
Driver seat control unit  Operates the seat sliding motor for a constant amount
BCMRecognizes the following status and transmits them to the driver seat control unit
via CAN communication
 Door switch signal (front driver side)
 Key switch signal
 Ignition switch signal
IPDM E/RRecognizes the following status and transmits it to the driver seat control unit via
CAN communication
 Detente switch signal
Item Function
Front door switch (driver side) Detects front door (driver side) open/close status
Item Function
Sliding sensor Detects the front/rear position of seat
Item Function
Sliding motor Slides the seat frontward/rearward

AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
ENTRY ASSIST FUNCTION : System DiagramINFOID:0000000003759084
ENTRY ASSIST FUNCTION : System DescriptionINFOID:0000000003759085
OUTLINE
When the following condition is satisfied, the seat in the exiting position returns to the previous driving posi-
tion.
NOTE:
 This function is set to ON before delivery (initial setting).
 Further information for the system setting procedure. Refer to ADP-8, "
SYSTEM INITIALIZATION : Descrip-
tion".
OPERATION PROCEDURE
1. Turn the ignition switch to the ACC position.
2. Driver seat returns from the exiting position to entry position.
OPERATION CONDITION
Satisfy all of the following items. The entry assist function is not performed if any of these items are not satis-
fied.
DETAIL FLOW
JMJIA1816GB
Item Request status
SeatThe vehicle is not moved after performing the
exit assist function.
Switch inputs
 Power seat switch
 Set switch
 Memory switchOFF
(Not operated)

ADP-28
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
Order Input Output Control unit condition
1 Ignition switch —Driver seat control unit receives the signals of [ignition switch signal]
from BCM via CAN communication
2— Sliding motorDriver seat control unit operates the sliding motor when the operating
conditions are satisfied
Sliding sensor —Sliding sensor monitors the operating positions of seat, and then
stops the operation of sliding motor when the seat reaches the re-
corded address

AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-29
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
ENTRY ASSIST FUNCTION : Component Parts LocationINFOID:0000000003859814
1. BCM M118, M119, M122, M123 2. Combination meter M34 3. Key slot M99
4. Seat memory switch D13 5. Front door switch (driver side) B34 6. Reclining motor (driver side) B454
7. Lifting motor (front) (driver side)
B4558. Driver seat control unit B451,B4529.Sliding motor (driver side) B461
JMJIA1811ZZ

ADP-30
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
ENTRY ASSIST FUNCTION : Component Description
INFOID:0000000003759087
CONTROL UNITS
INPUT PARTS
Sensors
OUTPUT PARTS
INTELLIGENT KEY INTERLOCK FUNCTION
10. Lifting motor (rear) (driver side) B45611. Power seat switch (driver side) B459
(sliding, lifting switch)12. Power seat switch (driver side) B459
(reclining switch)
13. TCM (transmission control module)
F2314. Control device (detention switch)
M5715. ABS actuator and electric unit (con-
trol unit) E36
A. Behind the combination meter B. View with seat cushion and seatback
pad removedC. Back side of the seat cushion
D. Engine room (LH) E. View with the center console assem-
bly removedF. Engine room (RH)
Item Function
Driver seat control unitOperates the seat sliding motor for a certain amount depending on the ignition sig-
nal and door switch signal (driver side) from BCM
BCMRecognizes the following status and transmits it to the driver seat control unit via
CAN communication
 Ignition switch position: ACC/ON
Item Function
Sliding sensor Detect the front/rear position of seat
Item Function
Sliding motor Slides the seat frontward/rearward

AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-31
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
INTELLIGENT KEY INTERLOCK FUNCTION : System DiagramINFOID:0000000003759088
INTELLIGENT KEY INTERLOCK FUNCTION : System DescriptionINFOID:0000000003759089
OUTLINE
When unlocking doors by Intelligent Key or door request switch (driver side), the memory function is per-
formed first, the exit assist function is performed next and the entry assist function is performed last.
OPERATION PROCEDURE
1. Unlock doors by using Intelligent Key or door request switch (driver side).
2. The system performs exit assist operation and memory operation.
NOTE:
Further information for Intelligent Key interlock function. Refer to ADP-8, "
MEMORY STORING : Description".
OPERATION CONDITION
Satisfy all of the following items. The Intelligent Key interlock function is not performed if any of these items
are not satisfied.
DETAIL FLOW
JMJIA1815GB
Item Request status
Ignition positionOFF
Steering lock unitLOCK
Switch inputs
 Power seat switch
 Set switch
 Memory switchOFF
(Not operated)
Selector leverP position

ADP-32
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
Order Input Output Control unit condition
1 Door unlock signal
(CAN)
 Key ID signal (CAN)—Driver seat control unit receives the door unlock signal and the key
ID signal from BCM when unlocking the door with Intelligent Key or
driver side door request switch
2 — — Driver seat control unit performs the memory function
3 — — Driver seat control unit performs the exit assist function
4 — — Driver seat control unit performs the entry assist function

AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-33
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
INTELLIGENT KEY INTERLOCK FUNCTION : Component Parts LocationINFOID:0000000003859815
1. BCM M118, M119, M122, M123 2. Combination meter M34 3. Key slot M99
4. Seat memory switch D13 5. Front door switch (driver side) B34 6. Reclining motor (driver side) B454
7. Lifting motor (front) (driver side)
B4558. Driver seat control unit B451,B4529.Sliding motor (driver side) B461
JMJIA1811ZZ

ADP-34
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
INTELLIGENT KEY INTERLOCK FUNCTION : Component Description
INFOID:0000000003759091
CONTROL UNITS
10. Lifting motor (rear) (driver side) B45611. Power seat switch (driver side) B459
(sliding, lifting switch)12. Power seat switch (driver side) B459
(reclining switch)
13. TCM (transmission control module)
F2314. Control device (detention switch)
M5715. ABS actuator and electric unit (con-
trol unit) E36
A. Behind the combination meter B. View with seat cushion and seatback
pad removedC. Back side of the seat cushion
D. Engine room (LH) E. View with the center console assem-
bly removedF. Engine room (RH)
Item Function
Driver seat control unitPerforms memory function and entry/exit assist function after receiving the door un-
lock signal from BCM
BCMRecognizes the following status and transmits it to the driver seat control unit via
CAN communication
 Door lock: UNLOCK
(with Intelligent Key or driver side door request switch)
 Key ID signal
 Ignition switch signal