NISSAN TEANA 2014 Service Manual

ENGINE CONTROL SYSTEMEC-531
< SYMPTOM DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
1 - 6: The numbers refer to the order of inspection. Va l v e
mecha-
nism Timing chain
55555 55 5 EM-62
Camshaft
EM-47
Intake valve timing controlEM-62
Intake valve
3EM-78
Exhaust valve
Exhaust Exhaust manifold/Tube/Muf- fler/Gasket 55555 55 5 EM-33
, EX-6
Three way catalyst
Lubrica-
tion Oil pan/Oil strainer/Oil pump/
Oil filter/Oil gallery/Oil cooler 55555 55 5 EM-36
,
LU-9,
LU-11
, LU-7,
LU-17
Oil level (Low)/Filthy oil LU-9
Cooling Radiator/Hose/Radiator filler
cap
55555 55 45 CO-17
Thermostat 5
CO-22
Water pumpCO-20
Water galleryCO-7
Cooling fan
5CO-18
Coolant level (Low)/Contami-
nated coolant CO-11
NVIS (NISSAN Vehicle Immobilizer Sys-
tem — NATS) 11
SEC-63
SYMPTOM
Reference page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code A AAB AC AD AE AF AG AH AJ AK AL AM HA
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-532
< SYMPTOM DIAGNOSIS >[QR25DE]
INFORMATION DISPLAY IS MALFUNCTIONING
INFORMATION DISPLAY IS MALFUNCTIONING
Diagnosis ProcedureINFOID:0000000009462461
1.CHECK DTC WITH ECM
Check that DTC is not displayed.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Perform trouble diagnosis relevant to DTC indicated.
2.CHECK INFORMATION DISPLAY (ASCD)
Refer to EC-516, "Component Function Check"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace malfunctioning part.
3.CHECK INTERMITTENT INCIDENT
Refer to GI-43, "Intermittent Incident"
.
>> INSPECTION END
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

NORMAL OPERATING CONDITIONEC-533
< SYMPTOM DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000009462462
FUEL CUT CONTROL (AT NO LOAD AND HIGH ENGINE SPEED)
If the engine speed is above 2,000 rpm under no load (for ex
ample, the selector lever position is neutral and
engine speed is over 2,000 rpm) fuel will be cut off after some time. The exact time when the fuel is cut off var-
ies based on engine speed.
Fuel cut will be operated until the engine speed reaches 1,500 rpm, then fuel cut will be cancelled.
NOTE:
This function is different from deceleration contro l listed under Multiport Fuel Injection (MFI) System, EC-43,
"MULTIPORT FUEL INJECTION SYSTEM : System Description (w ith automatic air conditioner)" or EC-46,
"MULTIPORT FUEL INJECTION SYSTEM : System Description (with manual air conditioner)".
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-534
< PERIODIC MAINTENANCE >[QR25DE]
IDLE SPEED
PERIODIC MAINTENANCE
IDLE SPEED
InspectionINFOID:0000000009462463
1.CHECK IDLE SPEED
With CONSULT
Check idle speed in “DATA MONITOR” mode of “ENGINE” using CONSULT.
With GST
Check idle speed with Service $01 of GST.
>> INSPECTION END
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

IGNITION TIMINGEC-535
< PERIODIC MAINTENANCE > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
IGNITION TIMING
InspectionINFOID:0000000009462464
1.CHECK IGNITION TIMING
1. Attach timing light (A) to the ignition coil No.1 harness .
2. Check ignition timing. >> INSPECTION END
JPBIA5853ZZ
: Timing indicator
JPBIA5854ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-536
< PERIODIC MAINTENANCE >[QR25DE]
EVAPORATIVE EMISSION SYSTEM
EVAPORATIVE EMISSION SYSTEM
InspectionINFOID:0000000009462465
EVAP CANISTER
1.CHECK EVAP CANISTER
1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.
>> INSPECTION END
PBIB1212E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EVAP LEAK CHECKEC-537
< PERIODIC MAINTENANCE > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
EVAP LEAK CHECK
InspectionINFOID:0000000009462466
CAUTION:
• Do not use compressed air or a high pressure pump.
• Do not exceed 4.12 kPa (0.042 kg/cm
2, 0.6 psi) of pressure in EVAP system.
NOTE:
• Do not start engine.
• Improper installation of EVAP service port adapter [commercial service tool: (J-41413-OBD)] to the EVAP
service port may cause a leak.
1.EVAP LEAK CHECK
With CONSULT
1. Install EVAP service port adapter [commercial service tool: (J- 41413-OBD)] and pressure pump to EVAP service port.
2. Turn ignition switch ON.
3. Select the “EVAP SYSTEM CLOSE” in “WOR K SUPPORT” mode of “ENGINE” using CONSULT.
4. Touch “START”. A bar graph (Pressure indicating display) will appear on the screen.
5. Apply positive pressure to the EVAP system until t he pressure indicator reaches the middle of the bar
graph.
6. Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
7. Locate the leak using a leak detector [commercial service tool: (J-41416)]. Refer to EC-62, "EVAPORATIVE EMISSION SYS-
TEM : System Description".
Without CONSULT
1. Install EVAP service port adapter [commercial service tool: (J- 41413-OBD)] and pressure pump to EVAP service port.
SEF462UA
SEF200U
SEF462UA
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-538
< PERIODIC MAINTENANCE >[QR25DE]
EVAP LEAK CHECK
2. Apply battery voltage between the terminals of EVAP
canister vent control valve to make a closed EVAP
system.
3. To locate the leak, deliver positive pressure to the EVAP system until pressure gauge points reach 1.38 to
2.76 kPa (0.014 to 0.028 kg/cm
2, 0.2 to 0.4 psi).
4. Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
5. Locate the leak using a leak detector [commercial service tool: (J-41416)]. Refer to EC-62, "EVAPORATIVE EMISSION SYS-
TEM : System Description".
>> INSPECTION END
SEF200U
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POSITIVE CRANKCASE VENTILATIONEC-539
< PERIODIC MAINTENANCE > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
POSITIVE CRANKCASE VENTILATION
InspectionINFOID:0000000009462467
1.CHECK PCV VALVE
With engine running at idle, remove PCV valve from rocker cover. A
properly working valve makes a hissing noise as air passes through
it. A strong vacuum should be felt immediately when a finger is
placed over valve inlet.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace PCV valve. Refer to EC-21,
"Component Parts Location".
PBIB1589E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-540
< REMOVAL AND INSTALLATION >[QR25DE]
ECM
REMOVAL AND INSTALLATION
ECM
Removal and InstallationINFOID:0000000009462468
EXPLODED VIEW
REMOVAL
CAUTION:
Perform ADDITIONAL SERVICE WHEN REPLACING ECM. Refer to EC-174, "Work Procedure"
.
1. Remove battery. Refer to PG-73, "Removal and Installation (Battery)"
.
2. Disconnect ECM harness connectors.
3. Remove ECM mounting nuts, and then remove ECM.
INSTALLATION
Install in the reverse order of removal.
ECM bracket ECM
: Vehicle front
JPBIA5873ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM