PN switch NISSAN TIIDA 2009 Service Repair Manual

WW
N
O P
NOTE: This item is displayed, but cannot be monitored.
ACTIVE TEST
Display Item List
CONSULT-III Function (IPDM E/R) INFOID:0000000004306914
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
DATA MONITOR
All Signals, Main Signals, Selection From Menu
NOTE: FR WIPER INT “ON/OFF” Displays “FRONT WIPER INT (ON)/Other
(OFF)” status as judged from wiper switch signal.
FR WASHER SW “ON/OFF” Displays “FRONT WASHER Switch
(ON)/Other (OFF)” status as judged from wiper switch sig-
nal.
INT VOLUME “1 - 7” Displays intermittent operation dial position setting (1 - 7) as judged from wiper switch signal.
FR WIPER STOP “ON/OFF” Displays “Stopped (ON)/Operati ng (OFF)” status as judged from auto-stop signal.
VEHICLE SPEED “km/h” Displays vehicle speed stat us as judged from vehicle speed signal.
RR WIPER ON “ON/OFF” Displays “REAR WIPER (ON)/Other (O FF)” status as judged from wiper switch signal.
RR WIPER INT “ON/OFF” Displays “REAR WIPER INT (ON)/Other (OFF)” status as judged from wiper switch signal.
RR WASHER SW “ON/OFF” Displays “FRONT WASHER Switch
(ON)/Other (OFF)” status as judged from wiper switch sig-
nal.
RR WIPER STOP “ON/OFF” Displays “Stopp ed (ON)/Operating (OFF)” status as judged from auto-stop switch 1.
RR WIPER STP2 “ON/OFF” Displays “Stopp ed (ON)/Operating (OFF)” status as judged from auto-stop switch 2.
H/L WASH SW NOTE
“OFF” —
Monitor item Contents Test item Display on CONSULT-III screen Description
Front wiper LO output FR WIPER (LO) Front LO wiper can be operated by any ON-OFF operation.
Front wiper HI output FR WIPER (HI) Front HI wiper can be operated by any ON-OFF operation.
Front wiper INT output FR WIPER (INT) Front INT wiper can be operated by any ON-OFF operation.
Rear wiper output RR WIPER Rear wiper can be operated by any ON-OFF operation. IPDM E/R diagnostic Mode Description
SELF-DIAG RESULTS Displays IPDM E/R self-diagnosis results.
DATA MONITOR Displays IPDM E/R input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read. ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them. ALL SIGNALS Monitors all items.
MAIN SIGNALS Monitor the predetermined item.
SELECTION FROM MENU Selects items and monitors them. Item name
CONSULT-III
screen display Display or unit Monitor item selection
Description
ALL
SIGNALS MAIN
SIGNALS SELECTION
FROM MENU
FR wiper request FR WIP REQ STOP/1LOW/
LOW/HI × × ×
Signal status input from BCM
Wiper auto stop WIP AUTO STOP ACT P/STOP P × × ×Output status of IPDM E/R
Wiper protection WIP PROT OFF/BLOCK × × ×Control status of IPDM E/R

System Descrip-
tion " in “PG IPDM E/R” to make sure
that it is not in fail-safe status. Auto Active Test " .
Does front wiper operate normally? YES >> GO TO 2.
NO >> GO TO 4. Combination Switch Inspection " .
OK or NG OK >> GO TO 3.
NG >> Check combination switch (wiper switch). Refer to LT-63, " Combination Switch Inspection " .
- diagnosis results
NO DTC>>Replace BCM. Refer to
BCS-18, " Removal and Installation of BCM " .
CAN COMM CIRCUIT>>Check CAN communi cation line of BCM. Refer to BCS-17, " CAN Communication
Inspection Using CONSULT-III (Self-Diagnosis) " .
OK >> GO TO 5.
NG >> Repair or replace harness. Test item CONSULT-III screen display Description
Front wiper (HI, LO) output FRONT WIPER With a certain operation (OFF, HI ON,
LO ON), front wiper relay (Lo, Hi)
can be operated. Front wiper mo-
tor connector Terminal
GroundContinuity
E1 2 Yes

WW
N
O P
3. Check continuity between IPDM E/R connector (A) and front
wiper motor connector (B).
4. Check continuity between IPDM E/R harness connector (A) and ground.
OK or NG OK >> Replace front wiper motor. Refer to
WW-20, " Removal and Installation of Front Wiper Drive
Assembly " .
NG >> Repair or replace harness.
Only Front Wiper Low Does Not Operate INFOID:0000000004306917Auto Active Test " .
Does front wiper operate normally? YES >> Refer to
LT-63, " Combination Switch Inspection " .
NO >> GO TO 2. OK >> GO TO 3.
NG >> Repair or replace harness.

Auto Active Test " .
4. Check voltage between IPDM E/R connector and ground while front wiper LO is operating.
OK or NG OK >> Replace front wiper motor. Refer to
WW-20, " Removal and Installation of Front Wiper Drive
Assembly " .
NG >> Replace IPDM E/R. Refer to PG-27, " Removal and Installation of IPDM E/R " .
Only Front Wiper Hi gh Does Not Operate INFOID:0000000004306918Auto Active Test " .
Does front wiper operate normally? YES >> Refer to
LT-63, " Combination Switch Inspection " .
NO >> GO TO 2.

Combination Switch Inspection " .
OK or NG OK >> Replace BCM. Refer to
BCS-18, " Removal and Installation of BCM " .
NG >> Check combination switch (wiper switch). Refer to LT-63, " Combination Switch Inspection " .
Front Wiper Intermittent Operation S witch Position Cannot Be Adjusted INFOID:0000000004306920Combination Switch Inspection " .
OK or NG OK >> Replace BCM. Refer to
BCS-18, " Removal and Installation of BCM " .
NG >> Check combination switch (wiper switch). Refer to LT-63, " Combination Switch Inspection " .
Wiper Does Not Wipe Wh en Front Washer Operates INFOID:0000000004306921Combination Switch Inspection " .
OK or NG OK >> Replace BCM. Refer to
BCS-18, " Removal and Installation of BCM " .
NG >> Check combination switch (wiper switch). Refer to LT-63, " Combination Switch Inspection " .
Front Wiper Does Not Stop INFOID:0000000004306922Combination Switch Inspection " .
OK or NG OK >> Replace IPDM E/R. Refer to
PG-26, " IPDM E/R Power/Ground Circuit Inspection " .
NG >> Check combination switch (wiper switch). Refer to LT-63, " Combination Switch Inspection " .
Removal and Installation of Front Wiper Arms INFOID:0000000004306923
REMOVAL
1. Turn wiper switch on to operate wiper motor, and then turn wiper switch off (auto stop).
2. Open hood, remove wiper arm caps, and remove wiper arm nuts.
3. Raise wiper arm, and remove wiper arm from the vehicle.
INSTALLATION

WW
N
O P
1. Clean up the pivot area as shown. This will reduce possibility of
wiper arm looseness.
2. Prior to wiper arm installation, turn on wiper switch to operate wiper motor and then turn it off (auto stop).
3. Push wiper arm onto pivot shaft, paying attention to blind spline.
4. Lift the blade up and then set it down onto glass surface to set the blade center to clearance “L1” and “L2” immediately before
temporarily tightening the wiper arm nuts.
5. Spray washer fluid. Turn on wiper switch to operate wiper motor and then turn it off.
6. Make sure that wiper blades stop within clearance “L1” and “L2” and reposition as necessary.
7. Tighten wiper arm nuts to specification.
8. Attach wiper arm caps.
Adjustment of Wiper Arm Stop Location INFOID:0000000004306924
ADJUSTMENT To adjust the wiper arm stop location, the wiper arm must be removed and installed. Refer to WW-18," Removal and Installation of Front Wiper Arms " .

Removal and Installation of Front Wiper Arms " .
3. Remove cowl top cover. Refer to EI-22 .
4. Disconnect wiper motor connector.
5. Remove front wiper drive assembly bolts, and remove front wiper drive assembly.
INSTALLATION
1. Install front wiper drive assembly.
2. Connect wiper motor connector. Turn wiper switch on to operate wiper motor, then turn wiper switch off
(auto stop).
3. Install cowl top cover. Refer to EI-22 .
4. Install the wiper arms. Refer to WW-18, " Removal and Installation of Front Wiper Arms " .
Removal and Installation of Front Washer Nozzle INFOID:0000000004306926
REMOVAL
1. Remove cowl top cover. Refer to EI-22, " Removal and Installation " .
2. Remove washer tube. 1. Front RH wiper blade 2. Front RH wiper arm 3. Wiper arm cap
4. Front wiper drive assembly 5. Front LH wiper arm 6. Wiper arm cap
7. Front LH wiper blade

WW
N
O P
Removal and Installation of
Front Wiper and Washer Switch INFOID:0000000004306930
REMOVAL 1. Remove the steering column cover. Refer to IP-11 .
2. Disconnect the wiper and washer switch connector.
3. Pull wiper and washer switch (1) toward the passenger door while pressing pawls (A) in direction shown by the arrow, and
remove it from the base.
INSTALLATION Installation is in the reverse order of removal.
Inspection of Front Wiper and Washer Switch Circuit INFOID:0000000004306931
Refer to LT-63, " Combination Switch Inspection " .
Removal and Installation of Washer Tank INFOID:0000000004306932
REMOVAL 1. Remove the front grille. Refer to EI-21, " Removal and Installation " .
2. Remove clip (A) and pull washer tank inlet (1) out of washer tank.
• : Vehicle front
3. Remove the front bumper. Refer to EI-15, " Removal and Installation " .
4. Disconnect the washer motor connector and washer fluid level sensor connector.
5. Remove the washer tank screw (A). • : Vehicle front
6. Remove the washer tube (1), and remove washer tank (2) from the vehicle.
• : Vehicle front 1. Washer nozzle LH 2. Washer nozzle RH 3. Joint washer tube
4. Washer tube 5. Clip 6. Clamp
7. Washer tank

WW
N
O P
REAR WIPER AND WASHER SYSTEM
Component Parts and Har ness Connector Location INFOID:0000000004306934
System Description INFOID:0000000004306935
• The wiper switch (combination switch ) is composed of a combination of 5 output terminals and 5 input termi-
nals. Terminal combination status is read by the BCM (body control module) when switch is turned ON.
• The BCM controls rear wiper ON and INT (intermittent) operation.
Power is supplied at all times
• through 40A fusible link (letter g , located in fuse and fusible link box)
• to BCM terminal 70.
With the ignition switch in ON or START position, power is supplied
• through 15A fuse [No. 4, located in the fuse block (J/B)]
• to combination switch terminal 2
• through 10A fuse [No. 6, located in the fuse block (J/B)]
• to BCM terminal 38.
Ground is supplied
• to BCM terminal 67, and
• to combination switch terminal 12
• through grounds M57 and M61.
REAR WIPER OPERATION When the ignition switch is in the ON or START position, and the rear wiper switch is in the ON position, the
BCM detects a rear wiper ON request through the combi nation switch (wiper switch) reading function and con-
trols the rear wiper motor as follows.
Power is supplied
• through BCM terminal 55
• to rear wiper motor terminal 1.
Ground is supplied
• to rear wiper motor terminal 3

OK >> GO TO 4.
NG >> Repair or replace harness. OK >> GO TO 5.
NG >> Repair or replace harness. " CONSULT-III Function (IPDM E/R) " . When rear wiper is oper-
ating, check voltage between BCM harness connector and
ground.
OK or NG OK >> Replace rear wiper motor. Refer to
WW-32, " Removal and Installation " .
NG >> Replace BCM. Refer to BCS-18, " Removal and Installation of BCM " .
OK >> Replace BCM. Refer to
BCS-18, " Removal and Installation of BCM " .
NG >> Check the wiper switch. Refer to BCS-3, " System Description " .
Rear Wiper Stop Position Is Incorrect INFOID:0000000004306942