NISSAN X-TRAIL 2003 Service Repair Manual

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
EM-129
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting — Engine NoiseEBS00LR8
PBIC2311E

EM-130
[YD22DDTi]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

Use the Chart Below to Help You Find the Cause of the Symptom.EBS00LR9
1. Locate the area where noise occurs.
2. Confirm the type of noise.
3. Specify the operating condition of engine.
4. Check specified noise source.
If necessary, repair or replace these parts.
A: Closely related B: Related C: Sometimes related —: Not relatedLocation
of noiseType of
noiseOperating condition of engine
Source of
noiseCheck itemRefer-
ence page Before
warm-
upAfter
warm-
upWhen
start-
ingWhen
idlingWhen
racingWhile
driving
To p o f
engine
Rocker
cover
Cylinder
headTicking or
clickingCA—AB—Tappet
noiseValve clearanceEM-175
Rattle C A — A B CCamshaft
bearing
noiseCamshaft oil clearance
Camshaft runoutEM-172EM-171
Crank-
shaft pul-
ley
Cylinder
block
(Side of
engine)
Oil panSlap or
knock—A—BB—Piston pin
noisePiston to piston pin
clearance
Connecting rod bush-
ing oil clearanceEM-226
EM-228
Slap or
rapA ——BBAPiston
slap noisePiston to cylinder bore
clearance
Piston ring side clear-
ance
Piston ring end gap
Connecting rod bend
and torsionEM-230EM-227
EM-227
EM-228
Knock A B CBBBConnect-
ing rod
bearing
noiseConnecting rod bush-
ing oil clearance
Connecting rod bear-
ing oil clearance (Big
end)EM-228EM-232
Knock A B — A B CMain
bearing
noiseMain bearing oil clear-
ance
Crankshaft runoutEM-233EM-232
Front of
engine
Timin g
chain
caseTapping or
tickingA A —BBBTiming
chain and
chain ten-
sioner
noiseTiming chain cracks
and wear
Timing chain tensioner
operationEM-180
EM-185
Front of
engineSqueak-
ing or fizz-
ingAB—B—CDrive belts
(Sticking
or slip-
ping)Drive belts deflection
EM-131
Creaking A B A B A BDrive belts
(Slipping)Idler pulley bearing
operation
Squall
CreakA B —BABWater
pump
noiseWater pump operationCO-42,
"WATER
PUMP"

DRIVE BELTS
EM-131
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

DRIVE BELTSPFP:02117
Checking Drive BeltsEBS00LRA

Before inspecting engine, make sure engine has cooled down;
wait approximately 30 minutes after engine has been stopped.

Visually inspect all belts for wear, damage or cracks on contact-
ing surfaces and edge areas.

When measuring deflection, apply 98 N (10 kg, 22 lb) at the
marked point ( ).
CAUTION:

When checking belt deflection immediately after installa-
tion, first adjust it to the specified value. Then, after turn-
ing crankshaft two turns or more, re-adjust to the
specified value to avoid variation in deflection between
pulleys.

Tighten idler pulley lock nut by hand and measure deflection without looseness.
Belt Deflection:
*: When engine is cold.
Tension AdjustmentEBS00LRB

Adjust belts with the parts shown below.
CAUTION:

When a new belt is installed as a replacement, adjust it to the specified value under “New” value
because of insufficient adaptability with pulley grooves.

If the belt deflection of the current belt is out of the “Limit for re-adjusting”, adjust to the
“Adjusted” value.

When checking belt deflection immediately after installation, first adjust it to the specified value.
Then, after turning crankshaft two turns or more, re-adjust it to the specified value to avoid vari-
ation in deflection between pulleys.

Make sure the belts are fully fitted into the pulley grooves during installation.

Handle with care to avoid smearing the belts with engine oil or engine coolant.

Do not twist or bend the belts with strong force.
PBIC1251E
Applied beltBelt deflection with 98 N (10 kg, 22 lb) force applied* mm (in)
New Adjusted Limit for re-adjusting
A/C compressor belt 4 - 5 (0.16 - 0.20) 6 - 7 (0.24 - 0.28) 8.5 (0.335)
Alternator and water pump belt 9.0 - 10.5 (0.354 - 0.413) 11.0 - 12.5 (0.433 - 0.492) 16.5 (0.650)
Applied belt Belt adjustment method
A/C compressor belt Adjusting bolt on idler pulley
Alternator and water pump belt Adjusting bolt on alternator

EM-132
[YD22DDTi]
DRIVE BELTS

A/C COMPRESSOR BELT
1. Remove RH engine undercover.
2. Loosen idler pulley lock nut (A).
3. Turn adjusting bolt (B) to adjust. Refer to EM-131, "
Checking
Drive Belts" .
4. Tighten lock nut (A).
ALTERNATOR AND WATER PUMP BELT
1. Loosen adjusting lock nut (C).
2. Loosen alternator fixing bolts (D) (each on front and rear).
3. Turn adjusting bolt (E) to adjust. Refer to EM-131, "
Tension Adjustment" .
4. Tighten nut (C) and bolt (D) in this order.
Removal and InstallationEBS00LRC
REMOVAL
1. Loosen each belt. Refer to EM-131, "Tension Adjustment" .
2. Remove A/C compressor belt. Refer to EM-132, "
A/C COMPRESSOR BELT" .
3. Remove alternator and water pump belt. Refer to EM-132, "
ALTERNATOR AND WATER PUMP BELT" .
INSTALLATION
1. Install each belt on pulley in the reverse order of removal.
2. Adjust belt tension. Refer to EM-131, "
Tension Adjustment" .
3. Tighten nuts and bolts provided for adjustment to the specified torque.
4. Make sure again that each belt tension is as specified.Nut A:
: 31 - 39 N·m (3.1 - 4.0 kg-m, 23 - 28 ft-lb)
PBIC1252E
Nut C:
: 19 - 24 N·m (1.9 - 2.5 kg-m, 14 - 18 ft-lb)
Bolt D:
: 44 - 57 N·m (4.4 - 5.9 kg-m, 32 - 42 ft-lb)

AIR CLEANER AND AIR DUCT
EM-133
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

AIR CLEANER AND AIR DUCTPFP:16500
Removal and InstallationEBS00LRD
REMOVAL
1. Remove mass air flow sensor harness clamp.
2. Disconnect harness connector from mass air flow sensor.
3. Remove air duct, air cleaner case (upper)/ mass air flow sensor.

Add marks as necessary for easier installation.
4. Remove mass air flow sensor from air cleaner case (upper).
CAUTION:
Handle mass air flow sensor with following cares.

Do not shock it.

Do not disassemble it.

Do not touch its sensor.
5. Remove air cleaner case (lower) and air duct side.
INSTALLATION
Note the following, and install in the reverse order of removal.

Align marks. Attach each joint. Screw clamps firmly.
1. Air cleaner case (upper) 2. Clamp 3. Air duct
4. Mass air flow sensor 5. Grommet 6. Air duct side
7. Mounting rubber 8. Air cleaner case (lower) 9. Air cleaner filter
PBIC1235E

EM-134
[YD22DDTi]
AIR CLEANER AND AIR DUCT

CHANGING AIR CLEANER FILTER
Removal
1. Unfasten clips and lift up air cleaner case (upper).
2. Remove air cleaner filter.
Installation
Install in the reverse order of removal.

CHARGE AIR COOLER
EM-135
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

CHARGE AIR COOLERPFP:14461
Removal and InstallationEBS00LRE
REMOVAL
1. Remove charge air cooler cover.
2. Disconnect harness connector from turbocharger boost sensor.
3. Remove air inlet tube and air inlet hose.

Add marks as necessary for easier installation.
4. Remove charge air cooler.
5. Remove air inlet tube from charge air cooler.
6. Remove turbocharger boost sensor if necessary.
CAUTION:
When removing charge air cooler, close opening on turbocharger and on intake manifold with shop
cloth or other suitable material.
INSPECTION AFTER REMOVAL
Check air passages of charge air cooler core and fins for clogging, leaks or deformation. Clean or replace
charge air cooler if necessary.

Be careful not to deform core fins.

For cleaning procedure of charge air cooler core, refer to CO-35, "Checking Radiator".
INSTALLATION
Note the following, and install in the reverse order of removal.

Pay attention to identification mark color and direction when installing air inlet hose.

Align marks. Attach each joint. Screw clamps firmly.
1. Charge air cooler cover 2. Charge air cooler 3. Gasket
4. Air inlet tube 5. Clamp 6. Air inlet hose
7. Bottom bracket 8. Turbocharger boost sensor
PBIC2019E

EM-136
[YD22DDTi]
INTAKE MANIFOLD

INTAKE MANIFOLDPFP:14003
Removal and InstallationEBS00LRF
REMOVAL
WARNING:
To avoid the danger of being scalded, do not drain engine coolant when engine is hot.
1. Drain engine coolant. Refer to CO-31, "
Changing Engine Coolant" .
2. Remove air duct. Refer to EM-133, "
Removal and Installation" .
3. Remove charge air cooler. Refer to EM-135, "
Removal and Installation" .
4. Remove air inlet pipes. Refer to EM-141, "
Removal and Installation" .
5. Remove exhaust manifold insulator. Refer to EM-141, "
EXHAUST MANIFOLD AND TURBOCHARGER" .
1. Fuel gallery 2. Water hose 3. Air relief plug
4. Copper washer 5. Gasket 6. EGR passage
7. EGR volume control valve 8. Bracket 9. Washer
10. Water pipe 11. O-ring 12. EGR cooler
13. Exhaust manifold 14. Intake manifold 15. Cylinder head
16. Heater hose 17. Spill hose
PBIC2020E

INTAKE MANIFOLD
EM-137
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

6. Disconnect EGR volume control valve water hoses and wiring harness.
7. Disconnect heater hose.
8. Remove EGR Cooler.
9. Remove injection tube center. Refer to EM-157, "
Removal and Installation" .
CAUTION:
Be careful not to spill fuel in the engine component.
10. Remove water pipe.
11. Remove fuel hoses and fuel gallery.

To prevent fuel from flowing out, plug the opening of the hose with plug after disconnection.
CAUTION:
Be careful not to spill fuel in the engine component.
12. Loosen bolts and nuts in reverse order of that shown in the fig-
ure, and remove intake manifold.
CAUTION:
Cover engine openings to avoid entry of foreign materials.
13. Remove EGR volume control valve from intake manifold.
INSPECTION AFTER REMOVAL
Surface Distortion

Check distortion on the mounting surface with a straightedge
and feeler gauge.

If it exceeds the limit, replace intake manifold.
INSTALLATION
Following instructions below, install in the reverse order of removal.
1. Install EGR volume control valve.

Handle with care avoiding any shocks.

Do not disassemble.
2. Install intake manifold.

Tighten fixing bolts and nuts in numerical order as shown in the figure.

When stud bolts come off, install with the following torque.
PBIC0676E
Limit : 0.1 mm (0.004 in)
PBIC0677E
: 10 - 11 N·m (1.0 - 1.2 kg-m, 87 - 104 in-lb)

EM-138
[YD22DDTi]
INTAKE MANIFOLD

3. Install water hose.

Install water hose by referring to identification marks avoiding
twisting.

When an insert stopper is not provided with the pipe, insert
the hose up to dimension A. When the pipe is shorter than
dimension A, insert hose fully until it reaches the end.

When an insert stopper is provided on the pipe side, insert the
hose until it reaches the bulge.
4. Install remaining parts in the reverse order of removal.
5. Before starting engine, bleed air from fuel piping. Refer to FL-18, "
Air Bleeding" .
INSPECTION AFTER INSTALLATION
Start engine and increase engine speed to check for fuel leak.
CAUTION:
Do not touch the engine immediately after stopped as engine becomes extremely hot.
NOTE:
Use mirrors for checking at points out of clear sight.Dimension A : 25 - 30 mm (0.984 - 1.181 in)
PBIC2021E