NISSAN X-TRAIL 2003 Service Repair Manual

FRONT FOG LAMP
LT-53
C
D
E
F
G
H
I
J
L
MA
B
LT

Wiring Diagram — F/FOG — EKS003DG
TKWA1535E

LT-54
FRONT FOG LAMP

Aiming Adjustment EKS003DH
1. Set the distance between the screen and the center of the fog
lamp lens as shown at left.
2. Turn front fog lamps ON.
3. Insert a phillips screwdriver into the access hole and enage the
tip of the screwdriver with the gear of the adjuster as shown at
left. The aiming adjuster can now be turned by turning the
screwdriver.
4. Adjust front fog lamps so that the top edge of the high intensity
zone is 100 mm (4 in) below the height of the fog lamp centers
as shown at left.

When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
PKIA8619E
PKIA5558E
MEL328G

FRONT FOG LAMP
LT-55
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003DI
1. Remove fog lamp. Refer to LT- 5 5 , "Removal and Installation" .
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
4. Install in the reverse order of removal.
CAUTION:

Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.

Do not leave bulb out of fog lamp housing for a long time because dust, moisture smoke, etc. May
affect the performance of fog lamp. When replacing bulb, be sure to replace it with new one.
Removal and Installation EKS003DJ
REMOVAL
1. Remove fender protector. Refer to EI-21, "FENDER PROTECTOR" .
2. Disconnect fog lamp connector.
3. Remove fog lamp mounting nuts from fog lamp bracket.
4. Pull out fog lamp from vehicle and disconnect connector.
INSTALLATION

Install fog lamp in the reverse order of removal, observing the tightening torque shown below.Front fog lamp :12V 55W (H11)
PKIA5559E
PKIA5560E
Fog lamp mounting bolt
Tightening torque
: 5.5 N·m (0.56 kg-m, 49 in-lb)

LT-56
REAR FOG LAMP

REAR FOG LAMPPFP:26550
System Description EKS00ESB
DESCRIPTION
Power is supplied at all times to rear fog lamp relay terminal 3

through 10A fuse (No. 36, located in the fuse and fusible link box).
With the lighting switch in the 2ND position and LOW (“B”) position, power is supplied

through 10A fuse (No. 31, located in the fuse and fusible link box)

to lighting switch terminal 11

through lighting switch terminal 12

to fog lamp switch terminal 32

through fog lamp switch terminal 33

to rear fog lamp relay terminal 2.
FOG LAMP OPERATION
The front and rear fog lamp switch is built into the combination switch. The lighting switch must be in the 1st or
2nd position for rear fog lamp operation.
With the fog lamp switch in the ON position, ground is supplied

to rear fog lamp relay terminal 1

through the fog lamp switch and grounds E24 and E50.
The rear fog lamp relay is energized and power is supplied

from rear fog lamp relay terminal 5

to rear fog lamp terminal 1

to combination meter terminal 13.
Ground is supplied

to each fog lamp terminal 2 through grounds E24 and E50.
With power and ground supplied, the rear fog lamps illuminate.
Ground is supplied

to combination meter terminal 64 through grounds M27 and M70.

REAR FOG LAMP
LT-57
C
D
E
F
G
H
I
J
L
MA
B
LT

Wiring Diagram -R/FOG-/Without Front Fog LampEKS003BV
TKWA1536E

LT-58
REAR FOG LAMP

Wiring Diagram -R/FOG-/With Front Fog LampEKS003BW
TKWA1537E

REAR FOG LAMP
LT-59
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS0015L
1. Remove rear fog lamp. Refer to LT- 5 9 , "Removal and Installa-
tion" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS0015M
REMOVAL
1. Remove rear fog lamp mounting screws (2).
2. Take out rear fog lamp from bumper, then disconnect connector.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Rear fog lamp : 12V 21W
SKIA0052E
SKIA0090E
Rear fog lamp mounting screws
Tightening torque : 1.4 N·m (0.14 kg-m, 12 in-lb)

LT-60
CLEARANCE LAMP/TAIL LAMP

CLEARANCE LAMP/TAIL LAMPPFP:26010
Bulb Replacement (Clearance Lamp)EKS001UR
Refer to LT- 1 6 , "Bulb Replacement for Headlamp and Clearance lamp" .
Bulb Replacement (Tail lamp)EKS001US
Refer to LT- 6 3 , "Bulb Replacement" .
Removal and Installation of Clearance LampEKS001UT
Refer to LT- 1 7 , "Removal and Installation for Headlamp" .
Removal and Installation of Tail lampEKS001UU
Refer to LT- 6 3 , "Removal and Installation" .

HIGH-MOUNTED STOP LAMP
LT-61
C
D
E
F
G
H
I
J
L
MA
B
LT

HIGH-MOUNTED STOP LAMPPFP:26590
Bulb ReplacementEKS0034W
Refer to LT- 4 3 , "Bulb Replacement" .
Removal and InstallationEKS0034X
Refer to LT- 4 3 , "Removal and Installation" .

LT-62
REAR COMBINATION LAMP

REAR COMBINATION LAMP PFP:26554
Wiring Diagram —STOP/L— EKS003C6
TKWA0067E